 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MPE-25S Series Si l O Single Output, 25W 2 Compact, Enclosed AC/DC Power Supplies Electrical Specifications Key Features: * 25W Output Power * Universal 85-264 AC Input * EN60950 Approved * Four Single Output Models * Meets EN55022 * >325 kHour MTBF * Compact Metal Enclosure Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Input Voltage Range Input Frequency Input Current Inrush Current Safety Ground Leakage Current Conditions Min. Typ. 85 120 47 See Model Selection Guide Cold Start, 115 VAC 15.0 Cold Start, 230 VAC 30.0 115 VAC 230 VAC Universal Max. 264 370 63 Units VAC VDC Hz A Pk 0.45 0.75 Max. mA Units Output Parameter Output Voltage Output Current Output Voltage Adjustment Output Voltage Tolerance, See Note 1 Ripple & Noise (20 MHz) , See Note 2 Conditions Min. Typ. See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide 115 VAC 12 230 VAC 80 115 VAC 800 230 VAC 300 115 VAC 50 230 VAC 50 0.02 Continuous (Autorecovery) See Note 3 115 See Note 4 135 Conditions Input to Output Input to Ground Output to Ground 500 VDC Conducted Electrostatic Discharge (ESD) RF Field Susceptibility Electrical Fast Transients/Bursts On Mains Surge Min. 3,000 1,500 500 Typ. RoHS Compliant Hold-Up Time Set-Up Time Rise Time Temperature Coefficient Short Circuit Protection Over Voltage Protection Overload Protection mSec mSec mSec %/C 135 165 Max. % Vout % Iout Units VAC General Parameter Isolation Voltage Isolation resistance EMI/RFI MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com EMC Compliance Switching Frequency 100 M EN 55022; EN 61000-3-2, -3 IEC/EN 61000-4-2, -6, -8, -11 IEC/EN61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 56 kHz Units C C % Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Min. Typ. Max. -10 +25 +60 -20 +85 Free Air Convection (See Derating Curve) RH, Non-condensing 20 90 Ambient Physical Case Size Case Material Weight 3.90 x 3.82 x 1.42 Inches (99.0 x 97.0 x 36.0 mm) Vented Metal Enclosure 13.7 Oz (0.39 kg) Conditions Min. Typ. Max. Units MIL HDBK 217F, 25C, Gnd Benign 325 kHours IEN 60950, IEC 60950 10~500 Hz, 2G 10 min/1 Cycle. Period of 60 min each along X, Y &Z Axis Reliability Specifications Parameter MTBF Safety Standards Vibration Model Selection Guide Input Model Number MPE-25S-05 MPE-25S-12 MPE-25S-15 MPE-25S-24 Current (A) 115 VAC 0.6 0.6 0.6 0.6 230 VAC 0.35 0.35 0.35 0.35 Voltage (VDC) Rated 5.0 12.0 15.0 24.0 Adjust 4.75 - 5.5 10.8 - 13.2 13.5 - 16.5 21.6 - 26.4 Output Current (A) Rated 5.0 2.1 1.7 1.1 Range 0 to 5.0 0 to 2.1 0 to 1.7 0 to 1.1 Output Voltage Tolerance (%) 2.0 1.0 1.0 1.0 Ripple & Noise (mV p-p) Efficiency (%, Typ) 50 100 100 100 72 76 77 80 Notes: 1. Output voltage tolerance includes the the effects of set point accuracy, line regulation and load regulation. 2. Ripple and noise is measured at 20 MHz bandwidth using a 12 inch twisted pair wire to connect to the power supply terminals. A 0.1 F and a 47 F capacitor are connected in parallel as close to the power supply terminals as possible. 3. Overvoltage protection is provided by a "hiccup mode" circuit. The unit recovers automatically when the fault condition is removed. 4. Overload protection is provided by foldback current limiting. The unit recovers automatically when the fault condition is removed. 5. Efficiency is measured with a 115 VAC input. 6. It is recommended that a fuse be used on the input of a power supply for protection. For the MPE-25S series, a 2.5A/250 VAC slow blow should be used. Mechanical Dimensions Pin Connections Pin 1 2 3 4 5 Function -Vout +Vout AC-Ground AC-Line AC-Neutral Notes: * All dimensions are typical in inches (mm) * Tolerance x.xx = 0.01 (0.25) Derating Curve Static Characteristics (24 Vout) MicroPower Direct www.micropowerdirect.com * 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 * FAX: (781) 344-8481 * E-Mail: sales@micropowerdirect.com |
Price & Availability of MPE-25S
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |