View AP230_4633947.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MMIC
Product Features
AP230
Applications
* Satellite * Repeater * Base Station * Converter * CATV * SMATV
* Small size * NO matching circuit needed * High efficiency * Dual supply voltage * Higher linearity * Higher productivity * Lower manufacturing cost * GaAs MMIC * 3MHz - 2150MHz * -63dBc CSO 135 Channels@ output Level +37dBmV * -60dBc CTB 135 Channels@ output Level +37dBmV * -70dBc CSO 8 Channels@ output Level +45dBmV * -73dBc CTB 8 Channels@ output Level +45dBmV
Package : SOIC-8
Descriptions
The power amplifier is designed for base stations and repeater systems. GaAs MMIC is used and attached on a copper carrier of 8 pin air cavity package with dual supply voltage
Operating Ranges
PARAMETER Device Voltage Case Temperature PARAMETER Device Voltage Device Current RF Input Power Storage Temperature UNIT VDC UNIT VDC mA dBm -40 -40 MIN MIN TYP +5 MAX +5.3 +85 MAX +5.5 +320 +10 +150 T=25, Vcc=5.0V, 75 system
Units
M Hz V mA dB dB dB dB dB dB m dB m dB dB dB m dB m dB dB c dB c dB c dB c dB c dB c 20 0
Absolute Minimum and Maximum Ratings
Specifications
P arame ter
Frequ ency R an ge Sup ply Vo ltage Sin gle En d ed CATV Evalu ation Circui t Cu rren t S21 -Gain S21 -Gain S21 -Gain S11 -In pu t Retu rn Los s S2 2-Outp u t R eturn L oss No ise Figu re OIP3 OIP1 S11 -In pu t Retu rn Los s S2 2-Outp u t R eturn L oss OIP3 OIP1 No ise Figu re C SO C TB 5 0 - 8 7 0M Hz XM D C SO 3 - 15 0M Hz C TB XM D
M inimum
Typical
3M Hz~2.1 5GHz 5
Max imum
C ondition
Vcc= 5V
2 20 16 15 14 Reverse ( 3 ~ 2 00 M Hz ) -16 -16 5.5 43 21 Forward ( 5 0 ~ 87 0M Hz ) -11 -11 37 21 4 -63 -60 -55 -70 -73 -70
2 50 3 M Hz 50 M Hz 2 15 0M Hz
+5 d Bm /2 to ne separated b y 1M Hz At 10 0M Hz
+5 d Bm /2 to ne separated b y 1M Hz At 80 0M Hz 1 3 5 chan n els ,+ 37 dB mV/ch ,Sing le 1 3 5 chan n els ,+ 37 dB mV/ch ,Sing le 1 3 5 chan n els ,+ 37 dB mV/ch ,Sing le 8 ch ann els,+4 5d Bm V/ch,Sin gle 8 ch ann els,+4 5d Bm V/ch,Sin gle 8 ch ann els,+4 5d Bm V/ch,Sin gle
Tel : 82-31-250-5011 rfsales@rfhic.com
All specifications may change without notice. Version 6.0
MMIC
AP230
Evaluation Board Layout 50-870MHz
Application 1 : Forward (50MHz ~ 2150MHz)
Vcc 10nF 4.7uF/16V 100nF 1nF RF IN 10nF 1.8nH 680 ohm L1 10nF 10nF 240 ohm 560nH 10nF D32212 10nF
RF OUT
AP230
240 ohm
10nF
0.5pF 560nH 1nF 100nF
10nF
Vcc
4.7uF/16V
The transformers L1 and L2, used on the RFHIC evaluation board are hand wound baluns with following spec[L1=3.5turn, ferrite core (Ferronics 12-340-k), L2=3.5 turn, ferrite core(TDK,L6 RID 3*3*3 H1.2)] was used. 0.12 1UEW wire was used. An SMT transformer (D32212,D31766), can also be used.
S-Parameters
20 15 10 Magnitude(dB) 5 0 -5 -10 -15 -20 -25 -30 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2
6 5.5 5
Noise Figure
S21
Noise Figure(dB)
4.5 4 3.5
S11
S22
3 2.5 50 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
Frequency(GHz)
Frequency(MHz)
25
P1dB
45 40
OIP3
20
35
Noise Figure(dB)
50 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
30 25 20 15 10 5
P1dB(dBm)
15
10
5
0
0 50 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
Frequency(MHz)
Frequency(MHz)
Level: +37dBmV FRQ 55.25 77.25 109.25 211.25 331.25 445.25 547.25 637.25 745.25 859.25
Tilt: 135CH FLAT CTB_RAW 69.4 68.7 66.4 66.2 65.6 66.2 66.7 66.2 65.5 65.1 CTB_COR 69.5 68.8 66.4 66.2 65.6 66.2 66.8 66.3 65.6 65.3 N-FLR 84.7 85.1 84.9 83.8 82.7 83.4 81.7 82.3 81.4 80.3 CSU_RAW 83.8 69.3 82.9 80.9 76.9 76.5 74.8 75.4 73.4 72 CSU_COR 88.1 69.5 87.2 83.9 78.2 77.6 75.7 76.5 74.2 72.8 CSU_FRQ 56 78 109.99 212.49 332.49 446.5 548.5 638.5 746.49 860.49 CSL_RAW 68.7 84.5 69.1 68.7 69.3 71.7 72.5 75.2 76.1 75.8 CSL_COR 68.8 88.8 69.2 68.8 69.5 72 73 76.2 77.5 78 CSL_FRQ 54 76.51 107.99 209.99 329.99 443.99 545.98 635.99 743.98 857.99
XMD(NCTA) 59.8 59.9 60.1 60.4 60.4 61.2 62.9 63.4 64.5 64.8
Tel : 82-31-250-5011 rfsales@rfhic.com
All specifications may change without notice. Version 6.0
MMIC
AP230
Application 2 : Reverse (3MHz ~ 200MHz)
Vcc 4.7uF/16V 100pF 1nF RF IN 100pF 1uF R0 10 ohm 7.5pF 22nF 4.7uH 1nF 100pF 4.7uF/16V 22nF 4.7uH 3.3uF
Evaluation Board Layout 5-200MHz
RF OUT D31250 1uF
AP230
3.3uF
Vcc
The transformers L1 and L2, used on the RFHIC evaluation board are hand wound baluns with following spec[L1=6 turn, ferrite core (TAIYO-YUDEN BF56 1.9*3.4*2.0), L2=3.5 turn, ferrite core(TDK,L6 RID 3*3*3 H1.2)] was used. 0.12 1UEW wire was used. An SMT transformer (D31044,D31766), can also be used.
S-Parameters
30 20
8
Noise Figure
10 0 -10 -20 -30
Noise Figure(dB)
180 210 240 270 300
S21
7
Magnitude(dB)
6
5
S22 S11
0
5
4
3
30 60 90 120 150
Frequency(MHz)
5
50
100
150
200
250
Frequency(MHz)
P1dB
25 20 15 10 5 0 5 50 100 150 200 250
OIP3
50 45
OIP3(dBm)
40 35 30 25 20 15 5 50 100 150 200 250
dBm
Frequency(MHz)
Frequency(MHz)
Level: +45dBmV FRQ 7 31 49 XMD(NCTA)
Tilt: 8CH FLAT CTB_RAW 79.9 78.6 79.8 CTB_COR 80.1 78.8 80.1 N-FLR 93.6 92.1 91.8 CSU_RAW 92.4 78.1 78.2 CSU_COR 96.7 78.4 78.4 CSU_FRQ 7.63 32 49.99 CSL_RAW 71.7 76.6 90.5 CSL_COR 71.7 76.8 94.8 CSL_FRQ 5.99 29.99 48.31
72.2 72.8 72.1
Tel : 82-31-250-5011 rfsales@rfhic.com
All specifications may change without notice. Version 6.0
MMIC
ESD Protection
AP230
For a safe use in all situations, it is recommended to have proper ESD control techniques while the device is being handled. Here are some recommended precautions; - Person at a workbench should be earthed via a wrist strap and a resistor. - All mains-powered equipment should be connected to the mains via an earth-leakage switch. - Equipment cases should be grounded. - Relative humidity should be maintained between 40% and 50%. - An ionizer is recommended. - Keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench
Package : SOIC-8 Type
Block Diagram
PIN No
1 5 4 8 2, 3, 6, 7 Exposed slug
Description
RF IN(2) RF OUT(1) RF IN(1) RF OUT(2) GND GND
1 2 3 4 AMP2
8 7 6 5
AMP1
Package Dimensions (Type: SOIC-8)
Recommended Pattern
RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC's liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC.
Tel : 82-31-250-5011 rfsales@rfhic.com
All specifications may change without notice. Version 6.0

▲Up To Search▲

Price & Availability of AP230

	To Download AP230 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .