View EN5336QI_4600468.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EN5336QI
3A Voltage Mode Synchronous Buck PWM DC-DC Converter with Integrated Inductor
External Feedback Output Voltage Programming Description
The EN5336QI is a Power System on Silicon DCDC converter. It is specifically designed to meet the precise voltage and fast transient requirements of present and future highperformance, low-power processor, DSP, FPGA, memory boards and system level applications in a distributed power architecture. Advanced circuit techniques, ultra high switching frequency, and very advanced, high-density, integrated circuit and proprietary inductor technology deliver highquality, ultra compact, non-isolated DC-DC conversion. Operating this converter requires only small value input and output ceramic capacitors, a soft-start capacitor and a resistor divider for voltage feedback to set the output voltage to the desired value. The Enpirion solution significantly helps in system design and productivity by offering greatly simplified board design, layout and manufacturing requirements. In addition, a reduction in the number of vendors required for the complete power solution helps to enable an overall system cost savings. All Enpirion products are RoHS compliant and lead-free manufacturing environment compatible. Typical Application Circuit
Features
* * * * * * * * * * * * *
*
Integrated INDUCTOR, MOSFETS, Controller Footprint 1/3rd that of competing solutions. Minimum external components. Up to 10W continuous output power. 5MHz operating frequency. High efficiency, up to 93%. VOUT accuracy 3% over line, load and temp. Wide input voltage range of 2.375V to 5.5V. External resistor divider for voltage feedback and output voltage selection. Output enable pin and Power OK signal. Programmable soft-start time. Programmable over-current protection. Thermal shutdown, short circuit, and UVLO RoHS compliant, MSL level 3, 260C reflow.
Applications
* * * * * * Point of load regulation for low-power processors, network processors, DSPs, FPGAs, and ASICs Notebook computers, servers, workstations Broadband, networking, LAN/WAN, optical Low voltage, distributed power architectures with 2.5V, 3.3V or 5V rails DSL, STB, DVR, DTV, iPC Ripple sensitive applications
VIN 22F
PVIN AVIN
POK
VOUT
VOUT
Ordering Information
XOV
SS AGND
47F
XFB PGND
15 nF
Part Number EN5336QI-T EN5336QI-E
Temp Rating ( C) Package -40 to +85 44-pin QFN T&R QFN Evaluation Board
Figure 1. Simple Layout.
1
www.enpirion.com
Rev 1.2 October 2008
EN5336QI
Pin Configuration
Below is a top view diagram of the EN5336QI package. NOTE: NC pins are not to be electrically connected to each other or to any external signal, ground, or voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage.
Figure 2. Pin-out diagram, top view.
Enpirion 2008 all rights reserved, E&OE
2
www.enpirion.com
Rev 1.2 October 2008
EN5336QI
Pin Descriptions
PIN 1-3 4-6 7 8-14 15 16 17-20 21-24 25-26 27 28 29 30-31 32 33 34 35 36 37 38 39 40 41 42-44 NAME NC NC(SW) NC VOUT NC(SW) NC PGND PVIN NC ROCP AVIN AGND NC XFB XOV NC POK NC SS EAIN EAOUT COMP ENABLE NC FUNCTION NO CONNECT - Do not electrically connect these pins to each other or to PCB. No Connect. These pins are internally connected to the switch node of the internal MOSFETs. NC(SW) pins are not to be electrically connected to any external signal, ground, or voltage. No connect - Do not electrically connect these pins to each other or to PCB. Regulated converter output. Connect these pins to the load and place output capacitor from these pins the PGND pins 17-18 No Connect. These pins are internally connected to the switch node of the internal MOSFETs. NC(SW) pins are not to be electrically connected to any external signal, ground, or voltage. No connect - Do not electrically connect these pins to each other or to PCB. Output power ground. Connect these pins to the ground electrode of the output filter capacitors. Refer to layout guideline section. Input power supply. Connect to input power supply. Decouple with input capacitor to PGND (pins 19-20). No connect - Do not electrically connect these pins to each other or to PCB. Optional Over Current Protection adjust pin. Place ROCP resistor between this pin and AGND (pin 40) to increase the over current trip point by 50%. Analog voltage input for the controller circuits. Connect this pin to the input power supply. Analog ground for the controller circuits. No connect - Do not electrically connect these pins to each other or to PCB. Voltage Feedback pin for external voltage divider network. Optional Over-Voltage Programming Feedback pin. No connect - Do not electrically connect these pins to each other or to PCB. Power OK is an open drain transistor for power system state indication. POK is a logic high when VOUT is with -10% to +20% of VOUT nominal. No connect - Do not electrically connect these pins to each other or to PCB. Soft-Start node. The soft-start capacitor is connected between this pin and AGND. The value of this resistor determines the startup timing. Optional Error Amplifier input. Allows for customization of the control loop. Optional Error Amplifier output. Allows for customization of the control loop. Optional Error Amplifier Buffer output. Allows for customization of the control loop. Input Enable. Applying a logic high, enables the output and initiates a softstart. Applying a logic low disables the output. No connect - Do not electrically connect these pins to each other or to PCB.
Enpirion 2008 all rights reserved, E&OE
3
www.enpirion.com
Rev 1.2 October 2008
EN5336QI
Block Diagram
POK PVIN
UVLO Thermal Limit ROCP Current Limit
power Good Logic
Over Voltage
VOUT
XOV
Over Voltage P-Drive VOUT (-) PWM Comp (+) N-Drive PGND
Sawtooth Generator
Compensation Network
(-) Error Amp ENABLE (+)
Voltage Selector
XFB
SS
Soft Start
Reference Voltage selector
Bandgap Reference
EAOUT
EAIN
COMP
Figure 3. System block diagram.
Absolute Maximum Ratings
CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond recommended operating conditions is not implied. Stress beyond Absolute maximum ratings may cause permanent damage to the device. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. Maximum Electrical Ratings
Voltages on: VIN, VOUT Voltages on XFB Voltages on: ENABLE -0.3V -0.3V -0.3V -40 C -65 C
Min
Max
7.0V 2.5V VIN + 0.3V +85 C +150 C +260 C
Maximum Thermal Ratings
Ambient operating range Storage Temperature Range Reflow Peak Body Temperature MSL3 (10 Sec)
Enpirion 2008 all rights reserved, E&OE
4
www.enpirion.com
Rev 1.2 October 2008
EN5336QI
Recommended Operating Conditions
PARAMETER Input Voltage Range EN5336QI Operating Ambient Temperature EN5336QI Operating Ambient Temperature Operating Junction Temperature SYMBOL VIN TA TA TJ MIN 2.375 0 -40 -40 MAX 5.5 +70 +85 +125 UNITS V C C C
Thermal Characteristics
SYMBOL PARAMETER TYP UNITS Thermal Shutdown TSD 150 C Thermal Shutdown Hysteresis TSDH 15 C Thermal Resistance: Junction to Case (0 LFM) (Note 1) 3 C/W JC Thermal Resistance: Junction to Ambient (0 LFM) 25 C/W JA Note 1: Based on a four-layer board and proper thermal design in line with JEDEC EIJ/JESD 51 Standards.
Electrical Characteristics
NOTE: VIN=5.5V over operating temperature range unless otherwise noted. Typical values are at TA = 25 C. PARAMETER
Operating Input Voltage Feedback Pin Voltage Drop out voltage Shut-Down Supply Current Switching Frequency
SYMBOL
VIN VFB VIN - VOUT IS FOSC VOUT
TEST CONDITIONS
MIN
2.375
TYP
0.75
MAX
5.5 600
UNITS
V V mV A MHz
Drop out voltage at full load ENABLE=0V 100 5 Over line, load and temperature -3.0
VOUT
Output Voltage Regulation Over Current Trip Piont 3.0 %
Maximum Continuous Output Current
IOCP Max voltage to ensure the converter is disabled 2.375V VIN 5.5V 5.5V < VIN VIN = 5.5V Threshold voltage for Logic Low Threshold voltage for Logic High (internally pulled high; can be left floating to achieve logic high) 1.8 4.5 A
Enable Operation
Disable Threshold Enable Threshold Enable Pin Current VSX Logic Low Threshold VSX Logic High Threshold VDISABLE VENABLE IENABLE VSX-Low VSX-High 0.8 1.8 2.0 50 0.8 VIN V V A V V
Voltage Select Operation
Enpirion 2008 all rights reserved, E&OE
5
www.enpirion.com
Rev 1.2 October 2008
EN5336QI SYMBOL
IVSX
PARAMETER
VSX Pin Current
TEST CONDITIONS
(VIN = 5.5V) VSx = GND VSx = VIN VSx = Open IPOK = 4mA (sink current)
MIN
TYP
50 0 0
MAX
UNITS
A
Power OK Operation
POK low voltage Max POK Voltage VPOK VPOK 0.4 VIN V V
Enpirion 2008 all rights reserved, E&OE
6
www.enpirion.com
Rev 1.2 October 2008
EN5336QI
Typical Performance Characteristics
VIN=5.0V
95 90 85
VIN=3.3V
V OUT = 3.3V V OUT = 2.5V
95 90 VOUT = 2.5V VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.8V 85 80 75 70 65 60 55 50 0.1 0.3 0.5 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9
Lo a d C urre nt ( A )
80 75 70 65 60 55 50
V OUT = 1.8V V OUT = 1.5V V OUT = 1.2V
0.1
0.3
0.5
0.7
0.9
1.1
1.3
1.5
1.7
1.9
2.1
2.3
2.5
2.7
2.9
Lo a d C urre nt ( A )
Efficiency versus Load, VIN = 5.0V
Efficiency versus Load, VIN = 3.3V
Load transient, 0 - 3A, VIN/VOUT = 5.5V/1.2V
Load transient, 0 - 3A, VIN/VOUT = 5.5V/3.3V
Start-up waveform, VIN/VOUT = 5.5V/1.2V
Shut-down waveform, VIN/VOUT = 5.5V/1.2V
Efficiency (%)
Efficiency (%)
Enpirion 2008 all rights reserved, E&OE
7
www.enpirion.com
Rev 1.2 October 2008
EN5336QI voltage:
Ra1 = (Vout - 0.75V ) * Rb1 0.75V
Theory of Operation
Synchronous Buck Converter
The EN5336QI is a synchronous, pin programmable power supply with integrated power MOSFET switches and integrated inductor. The nominal input voltage range is 2.45.0V. The output can be set to any voltage between 0.75V and VIN - 600mV. The feedback control loop is a type III voltage-mode and the part uses a low-noise PWM topology. Up to 3A of output current can be drawn from this converter. The 5MHz operating frequency enables the use of small-size output capacitors. The power supply has the following protection features: * Over-current protection (to protect the IC from excessive load current) * Thermal shutdown with hysteresis * Over-voltage protection * Under-voltage lockout circuit to disable the converter output when the input voltage is less than approximately 2.2V Additional features include: * * Soft-start circuit, limiting the in-rush current when the converter is powered up Power good circuit indicating whether the output voltage is within 90% - 120% of the programmed voltage
If over-voltage protection is desired, use the following equation to set the resistor Ra2 for the desired OVP trip-point:
Ra 2 = (OVPtrip - 0.90V ) * Rb 2 0.90V
By design, if both resistor dividers are the same, the OV trip-point will be 20% above the nominal output voltage.
VIN
PVIN
POK
VOUT
VOUT Ra2 Ra1
47F
22F
AVIN XOV SS XFB AGND PGND
CSS
Rb2
Rb1
Figure 4. VOUT and OVP resistor divider networks.
NOTE: if no OVP divider is present, there will be no over-voltage protection and POK will remain "high" as long as VOUT remains above 90% of the nominal VOUT setting.
Input Capacitor Selection
The EN5336QI requires about 20uF of input capacitance. Low-cost, low-ESR ceramic capacitors should be used as input capacitors for this converter. The dielectric must be X5R or X7R rated. In some applications, lower value capacitors are needed in parallel with the larger, capacitors in order to provide high frequency decoupling. It is recommended to use 10V rated MLCC capacitors. Table 2 lists some recommended part numbers for input capacitors.
Output Voltage Programming
The EN5336QI output voltage is programmed using a simple resistor divider network. Figure 4 shows the resistor divider configuration. The EN5336QI output voltage and over voltage thresholds are determined by the voltages presented at the XFB and XOV pins respectively. These voltages are set by way of resistor dividers between VOUT and AGND with the midpoint going to XFB and XOV. It is recommended that Rb1 and Rb2 resistor values be ~2k. Use the following equation to set the resistor Ra1 for the desired output
Enpirion 2008 all rights reserved, E&OE
8
www.enpirion.com
Rev 1.2 October 2008
EN5336QI
Table 2. Recommended input capacitors.
Description
10uF, 10V, 10% X7R, 1206 (2 capacitors needed) 22uF, 10V, 10% X5R, 1210 (1 capacitor needed)
Enable Operation
The ENABLE pin provides a means to shut down the device, or enable normal operation. A logic high will enable the converter into normal operation. When the ENABLE pin is asserted, the device will undergo a normal soft start. A logic low will disable the converter and cause it to shut down. When Enable goes low, circuitry internal to the device continue to operate to ensure the output voltage is gradually returned to zero and the circuits turn off subsequently. A short low going pulse on Enable is ignored.
MFG
Murata Taiyo Yuden Murata Taiyo Yuden
P/N
GRM31CR71A106KA01L LMK316B7106KL-T GRM32ER71A226KE20L LMK325B7226KM-T
Output Capacitor Selection
The EN5336QI has been optimized for use with approximately 50F of output capacitance. Low ESR ceramic capacitors are required with X5R or X7R rated dielectric formulation. Y5V or equivalent dielectric formulations must not be used as these lose capacitance with frequency, temperature and bias voltage. Output ripple voltage is determined by the aggregate output capacitor impedance. Output impedance, denoted as Z, is comprised of effective series resistance, ESR, and effective series inductance, ESL: Z = ESR + ESL. Placing output capacitors in parallel reduces the impedance and will hence result in lower ripple voltage.
1 Z Total = 1 1 1 + + ... + Z1 Z 2 Zn
Soft-Start Operation
Soft start is a method to reduce in-rush current when the device is enabled. The output voltage is ramped up slowly upon start-up. The output rise time is controlled by choice of a soft-start capacitor, which is placed between the SS pin (pin 37) and the AGND pin (pin 29). Rise Time: TR = Css* 75K During start-up of the converter, the reference voltage to the error amplifier is gradually increased from zero to its final level by an internal current source of typically 10uA. Typical soft-start rise time is 1mS to 3mS. The rise time is measured from the time when AVIN > VUVLO and the Enable signal crosses its logic high threshold. Typical SS capacitor values are in the range of 15nF to 50 nF.
Typical ripple versus capacitance is given below:
Output Capacitor Configuration 1 x 47 uF 3 x 22 uF Typical Output Ripple (mVp-p) (as measured on EN5336QI Evaluation Board) 30 15
Power-up Sequencing
The sequencing of AVIN, PVIN and ENABLE should meet the following requirements:
1. ENABLE should not be asserted before PVIN. 2. PVIN should not be applied before AVIN.
Table 3. Recommended output capacitors.
Description
22uF, 6.3V, 10% X5R, 1206 (3 capacitors needed) 47uF, 10V, 10% X5R, 1210 47uF, 6.3V, 10% X5R, 1210 (1 capacitor needed)
MFG
Murata Taiyo Yuden Murata AVX
P/N
GRM31CR60J226KE19L JMK316BJ226KL-T GRM32ER61A476KE20L 12106D476KAT2
Note that tying AVIN, PVIN and ENABLE together and brought up at the same time does meet these requirements.
POK Operation
The POK signal is an open drain signal from the converter indicating the output voltage is within the specified range. The POK signal will be a logic high when the output voltage is above 90%
Enpirion 2008 all rights reserved, E&OE
9
www.enpirion.com
Rev 1.2 October 2008
EN5336QI stops, the lower N-MOSFET is turned on and the POK signal goes low. When the output voltage drops below 95% of the programmed output voltage, normal PWM operation resumes and POK returns to its high state.
of VOUT and below the user programmed OVP trip-point. If the output voltage goes outside of this range, the POK signal will be a logic low until the output voltage has returned to within this range. In the event of an over-voltage condition the POK signal will go low and will remain in this condition until the output voltage has dropped to 95% of the programmed output voltage before returning to the high state. NOTE: If no over voltage protection is used, POK will remain "high" as long as VOUT remains above 90% of the nominal VOUT setting.
Thermal Overload Protection
Thermal shutdown will disable operation once the Junction temperature exceeds approximately 150C. Once the junction temperature drops by approx 25C, the converter will re-start with a normal soft-start.
Over-Current Protection
The current limit function is achieved by sensing the current flowing through the sense PMOSFET. When the sensed current exceeds the current limit, both NFET and PFET switches are turned off. If the over-current condition is removed, the over-current protection circuit will enable the PWM operation. This circuit is designed to provide high noise immunity. The nominal over current trip point is set to 4.5A. It is possible to increase the over-current set point by about 50% by connecting a 7.5k resistor between ROCP (pin 27) and GND. The typical voltage at the ROCP pin is 0.75V. In some cases, such as the start-up of FPGA devices, it is desirable to blank the over-current protection feature. In order to disable overcurrent protection, the ROCP pin should be tied to any voltage between 2.5V and PVIN.
Input Under-voltage Lock-out
Circuitry is provided to ensure that when the input voltage is below the specified voltage range, the converter will not start-up. Circuits for hysteresis, input de-glitch and output leading edge blanking are included to ensure high noise immunity and prevent false tripping.
Compensation
The EN5336QI is internally compensated through the use of a type 3 compensation network and is optimized for use with about 50uF of output capacitance and will provide excellent loop bandwidth and transient performance for most applications. (See the section on Capacitor Selection for details on recommended capacitor types.) Voltage mode operation provides high noise immunity at light load. In some cases modifications to the compensation may be required. For more information, contact Enpirion Applications Engineering support.
Over-Voltage Protection
When the output voltage exceeds 120% of the programmed output voltage, the PWM operation
Enpirion 2008 all rights reserved, E&OE
10
www.enpirion.com
Rev 1.2 October 2008
EN5336QI
Design Considerations for Lead-Frame Based Modules
Exposed Metal on Bottom of Package
Lead frame offers many advantages in thermal performance, in reduced electrical lead resistance, and in overall foot print. However, they do require some special considerations. In the assembly process lead frame construction requires that, for mechanical support, some of the lead-frame cantilevers be exposed at the point where wire-bond or internal passives are attached. This results in several small pads being exposed on the bottom of the package. Only the large thermal pad and the perimeter pads are to be mechanically or electrically connected to the PC board. The PCB top layer under the EN5336QI should be clear of any metal except for the large thermal pad. The "grayed-out" area in Figure 5 represents the area that should be clear of any metal (traces, vias, or planes), on the top layer of the PCB. Figure 6 shows the recommended PCB footprint for this device.
Figure 5. Lead-Frame exposed metal. Grey area highlights exposed metal that is not to be mechanically or electrically connected to the PCB.
Enpirion 2008 all rights reserved, E&OE
11
www.enpirion.com
Rev 1.2 October 2008
EN5336QI
Figure 6. Recommended PCB footprint.
Enpirion 2008 all rights reserved, E&OE
12
www.enpirion.com
Rev 1.2 October 2008
EN5336QI
Package Dimensions
Figure 7. Package dimensions.
Contact Information
Enpirion, Inc. 685 Route 202/206 Suite 305 Bridgewater, NJ 08807 Phone: 908-575-7550 Fax: 908-575-0775
Enpirion reserves the right to make changes in circuit design and/or specifications at any time without notice. Information furnished by Enpirion is believed to be accurate and reliable. Enpirion assumes no responsibility for its use or for infringement of patents or other third party rights, which may result from its use. Enpirion products are not authorized for use in nuclear control systems, as critical components in life support systems or equipment used in hazardous environment without the express written authority from Enpirion.
Enpirion 2008 all rights reserved, E&OE
13
www.enpirion.com

▲Up To Search▲

Price & Availability of EN5336QI

	To Download EN5336QI Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .