 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TSV611, TSV612 Rail-to-rail input/output 11 A, 120 kHz CMOS operational amplifiers Preliminary data Features Rail-to-rail input and output Low power consumption: 11 A typ at 5 V Low supply voltage: 1.5 to 5.5 V Gain bandwidth product: 120 kHz typ Unity gain stable Low input offset voltage: 1 mV max (A version) Low input bias current: 1 pA typ Temperature range: -40 to +85 C TSV611ILT - TSV611ICT In+ 1 VDD 2 In- 3 5 VCC + _ 4 Out SOT23-5 / SC70-5 TSV612IST - TSV612ID/DT Out1 In1In1+ VCC1 2 3 4 _ + _ + 8 7 6 5 VCC+ Out2 In2In2+ Applications Battery-powered applications Portable devices Signal conditioning Active filtering Medical instrumentation MSO8 / SO8 Description The TSV61x family of single and dual operational amplifiers offers low voltage, low power operation and rail-to-rail input and output. The devices also feature an ultra-low input bias current as well as a low input offset voltage. The TSV61x have a gain bandwidth product of 120 kHz while consuming only 11 A at 5 V. These features make the TSV61x family ideal for sensor interfaces, battery-supplied and portable applications, as well as active filtering. May 2009 Doc ID 15768 Rev 1 1/16 www.st.com 16 This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. Absolute maximum ratings and operating conditions TSV611, TSV612 1 Absolute maximum ratings and operating conditions Table 1. Symbol VCC Vid Vin Tstg Supply voltage (1) (2) Absolute maximum ratings Parameter Value 6 VCC VCC- -0.2 to VCC++0.2 -65 to +150 (4)(5) Unit V V V C Differential input voltage Input voltage (3) Storage temperature Thermal resistance junction to ambient SC70-5 205 250 250 125 150 4 300 1.5 200 C kV V kV mA model(6) model(8) C/W Rthja SOT23-5 MiniSO-8 SO-8 Tj ESD Maximum junction temperature HBM: human body MM: machine model(7) CDM: charged device Latch-up immunity 1. All voltage values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. Vcc-Vin must not exceed 6 V. 4. Short-circuits can cause excessive heating and destructive dissipation. 5. Rth are typical values. 6. Human body model: 100 pF discharged through a 1.5 k resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 7. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 ), done for all couples of pin combinations with other pins floating. 8. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to ground. Table 2. Symbol VCC Vicm Toper Operating conditions Parameter Supply voltage Common mode input voltage range Operating free air temperature range Value 1.5 to 5.5 VCC- -0.1 to VCC+ +0.1 -40 to +85 Unit V V C 2/16 Doc ID 15768 Rev 1 TSV611, TSV612 Electrical characteristics 2 Electrical characteristics Table 3. Electrical characteristics at VCC+ = +1.8 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25 C, and RL connected to VCC/2 (unless otherwise specified) Parameter Conditions Min. Typ. Max. Unit Symbol DC performance TSV61x TSV61xA Vio Offset voltage Tmin. < Top < Tmax. TSV61x Tmin. < Top < TmaxTSV61xA Input offset voltage drift Input offset current (Vout = Vcc/2) Input bias current (Vout = Vcc/2) Common mode rejection ratio 20 log (Vic/Vio) 2 1 Tmin. < Top < Tmax. 1 1 Tmin. < Top < Tmax. 0 V to 1.8 V, Vout = 0.9 V Tmin. < Top < Tmax. , RL = 10 k Vout = 0.5 V to 1.3 V Tmin. < Top < Tmax. VOH VOL High level output voltage Low level output voltage Isink Iout Isource Supply current (per operator) RL = 10 k Tmin. < Top < Tmax. RL = 10 k Tmin. < Top < Tmax. Vo = 1.8 V Tmin. < Top < Tmax. Vo = 0 V Tmin. < Top < Tmax. No load, Vout = Vcc/2 Tmin. < Top < Tmax. 5 5 5 5 tbd tbd 35 50 3 3 10 87 55 1 5 1 mV 6 2 V/C 10 100 10 100 pA pA pA pA dB dB dB dB mV 35 50 mV DVio Iio Iib CMR Avd Large signal voltage gain mA 10 8 12 12 A A ICC AC performance GBP Fu m Gm Gain bandwidth product Unity gain frequency Phase margin Gain margin RL = 10 k CL = 20 pF, , f = 100 kHz, Av = 1 RL = 10 k CL = 20 pF, , Av = 1 RL = 10 k, CL = 20 pF, Av = 1 RL = 10 k, CL = 20 pF, Av = 1 105 100 45 tbd kHz kHz Degrees dB Doc ID 15768 Rev 1 3/16 Electrical characteristics Table 3. TSV611, TSV612 Electrical characteristics at VCC+ = +1.8 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25 C, and RL connected to VCC/2 (unless otherwise specified) (continued) Parameter Slew rate Equivalent input noise voltage Conditions RL = 10 k, CL = 20 pF Av = 1, TSV61x f = 1 kHz tbd Min. Typ. 0.03 156 tbd Max. Unit V/s nV ----------Hz Symbol SR en THD+en Total harmonic distortion % 4/16 Doc ID 15768 Rev 1 TSV611, TSV612 Table 4. Symbol DC performance TSV61x TSV61xA Vio Offset voltage Tmin Parameter Min. Typ. Max. Unit 5 1 mV 6 2 2 1 10 100 10 100 V/C pA pA pA pA dB DVio Iio 1 1 Iib 1 60 CMR Avd VOH VOL tbd 35 50 93 3 3 35 50 dB mV mV 15 15 20 mA 20 10 14 14 A A ICC AC performance GBP Fu m Gm SR Gain bandwidth product Unity gain frequency Phase margin Gain margin Slew rate , RL = 10 k CL = 20 pF, f = 100 kHz, Av = 1 RL = 10 k, CL = 20 pF, Av = 1 RL = 10 k, CL = 20 pF, Av = 1 RL = 10 k, CL = 20 pF, Av = 1 , RL = 10 k CL = 20 pF, AV = 1 110 100 tbd tbd 0.032 kHz kHz Degrees dB V/s Doc ID 15768 Rev 1 5/16 Electrical characteristics Table 4. Symbol en THD TSV611, TSV612 VCC+ = +3.3 V, VCC- = 0 V, Vicm = VCC/2, Tamb = 25 C, RL connected to VCC/2 (unless otherwise specified) (continued) Parameter Equivalent input noise voltage Total harmonic distortion f = 1 kHz tbd Min. Typ. 156 tbd Max. Unit nV ----------Hz % 6/16 Doc ID 15768 Rev 1 TSV611, TSV612 Table 5. Symbol DC performance TSV61x TSV61xA Vio Offset voltage Tmin Parameter Min. Typ. Max. Unit 5 1 mV 6 2 2 1 10 100 10 100 V/C pA pA pA pA dB DVio Iio 1 1 Iib 1 60 CMR SVR Avd VOH VOL Vcc = 1.8 to 5 V RL = 10 k Vout = 0.5 V to , 4.5 V RL = 10 k Tmin. < Top < Tmax. RL = 10 k Tmin. < Top < Tmax. Vo = 5 V Vo = 0 V No load, Vout = 2.5 V Tmin. < Top < Tmax. 75 tbd 35 50 96 96 3 3 35 50 dB dB mV mV tbd tbd 20 mA 20 11 14 tbd A A ICC AC performance GBP Fu m Gm SR Gain bandwidth product Unity gain frequency Phase margin Gain margin Slew rate RL = 10 k CL = 20 pF, , f = 100 kHz, Av = 1 RL = 10 k, CL = 20 pF, Av = 1 RL = 10 k, CL = 20 pF, Av = 1 RL = 10 k, CL = 20 pF, Av = 1 RL = 10 k CL = 20 pF, , AV = 1 120 109 53 14 0.034 kHz kHz Degrees dB V/s Doc ID 15768 Rev 1 7/16 Electrical characteristics Table 5. Symbol en THD TSV611, TSV612 VCC+ = +5 V, VCC- = 0 V, Vicm = VCC/2, Tamb = 25 C, RL connected to VCC/2 (unless otherwise specified) (continued) Parameter Equivalent input noise voltage Total harmonic distortion f = 1 kHz fin = 1 kHz, Av = 1, Vout = 2 Vpp Min. Typ. 156 0.1 Max. Unit nV ----------Hz % 8/16 Doc ID 15768 Rev 1 TSV611, TSV612 Package information 3 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Doc ID 15768 Rev 1 9/16 Package information TSV611, TSV612 3.1 SOT23-5 package information Figure 1. SOT23-5L package mechanical drawing Table 6. SOT23-5L package mechanical data Dimensions Ref. Min. A A1 A2 B C D D1 e E F L K 2.60 1.50 0.10 0 degrees 0.90 0.35 0.09 2.80 0.90 Millimeters Typ. 1.20 Max. 1.45 0.15 1.05 0.40 0.15 2.90 1.90 0.95 2.80 1.60 0.35 3.00 1.75 0.60 10 degrees 0.102 0.059 0.004 1.30 0.50 0.20 3.00 0.035 0.013 0.003 0.110 Min. 0.035 Inches Typ. 0.047 Max. 0.057 0.006 0.041 0.015 0.006 0.114 0.075 0.037 0.110 0.063 0.013 0.118 0.069 0.023 0.051 0.019 0.008 0.118 10/16 Doc ID 15768 Rev 1 TSV611, TSV612 Package information 3.2 SC70-5 (or SOT323-5) package information Figure 2. SC70-5 (or SOT323-5) package mechanical drawing SIDE VIEW DIMENSIONS IN MM GAUGE PLANE COPLANAR LEADS SEATING PLANE TOP VIEW Table 7. SC70-5 (or SOT323-5) package mechanical data Dimensions Ref Min A A1 A2 b c D E E1 e e1 L < 0.26 0 0.80 0.15 0.10 1.80 1.80 1.15 0.80 Millimeters Typ Max 1.10 0.10 0.90 1.00 0.30 0.22 2.00 2.10 1.25 0.65 1.30 0.36 0.46 8 0.010 2.20 2.40 1.35 0.315 0.006 0.004 0.071 0.071 0.045 Min 0.315 Inches Typ Max 0.043 0.004 0.035 0.039 0.012 0.009 0.079 0.083 0.049 0.025 0.051 0.014 0.018 0.087 0.094 0.053 Doc ID 15768 Rev 1 11/16 Package information TSV611, TSV612 3.3 SO-8 package information Figure 3. SO-8 package mechanical drawing Table 8. SO-8 package mechanical data Dimensions Ref. Min. A A1 A2 b c D E E1 e h L L1 k ccc 1 0.25 0.40 0.10 1.25 0.28 0.17 4.80 5.80 3.80 Millimeters Typ. Max. 1.75 0.25 0.004 0.049 0.48 0.23 4.90 6.00 3.90 1.27 0.50 1.27 1.04 8 0.10 1 0.010 0.016 5.00 6.20 4.00 0.011 0.007 0.189 0.228 0.150 Min. Inches Typ. Max. 0.069 0.010 0.019 0.010 0.193 0.236 0.154 0.050 0.020 0.050 0.040 8 0.004 0.197 0.244 0.157 12/16 Doc ID 15768 Rev 1 TSV611, TSV612 Package information 3.4 MiniSO-8 package information Figure 4. MiniSO-8 package mechanical drawing Table 9. MiniSO-8 package mechanical data Dimensions Ref. Min. A A1 A2 b c D E E1 e L L1 L2 k ccc 0 0.40 0 0.75 0.22 0.08 2.80 4.65 2.80 Millimeters Typ. Max. 1.1 0.15 0.85 0.95 0.40 0.23 3.00 4.90 3.00 0.65 0.60 0.95 0.25 8 0.10 0 0.80 0.016 3.20 5.15 3.10 0 0.030 0.009 0.003 0.11 0.183 0.11 Min. Inches Typ. Max. 0.043 0.006 0.033 0.037 0.016 0.009 0.118 0.193 0.118 0.026 0.024 0.037 0.010 8 0.004 0.031 0.126 0.203 0.122 Doc ID 15768 Rev 1 13/16 Ordering information TSV611, TSV612 4 Ordering information Table 10. Order codes Temperature range Package Packing Marking K12 SOT23-5 TSV611AILT Tape & reel TSV611ICT SC70-5 TSV611AICT -40 C to 85 C TSV612ID/DT SO-8 TSV612AID/DT TSV612IST MSO-8 TSV612AIST Tape & reel K115 Tube & Tape & reel V612AI K113 V612I K11 K12 K11 Order code TSV611ILT 14/16 Doc ID 15768 Rev 1 TSV611, TSV612 Revision history 5 Revision history Table 11. Date 28-May-2009 Document revision history Revision 1 Initial release. Changes Doc ID 15768 Rev 1 15/16 TSV611, TSV612 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16 Doc ID 15768 Rev 1 |
Price & Availability of TSV611
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |