View D1U-W-1200-12-HA1C_4514771.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

D1U-W-1200-12-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
PRODUCT OVERVIEW
The D1U-W-1200 is a 1200 Watt, power-factor-corrected (PFC) front-end power supply for hot-swapping redundant systems. The main output is 12V and standby output of either 5V or 3.3V. Packaged in 1U low profile, it is designed to deliver reliable bulk power to servers, workstations, storage systems or any 12V distributed power architecture systems requiring high power density. The highly efficient electrical and thermal design with internal cooling fans supports reliable operation conditions. The D1U-W-1200 is designed to auto-recover from over-temperature faults. Status information is provided with front panel LEDs, logic signals and I2C management interface. Three units can be packaged into an optional 19" 1U power shelf to provide up to 3.6kW of power. The S1U-X3 is a 1U x 19" EIA Rack Mount Power Shelf designed for holding three D1U Front End Power Supplies in current sharing applications. It is intended for distributed power architecture applications in the Servers, Storage Networking and Data Communications markets. There are two lug terminal connections for #2 AWG cabling for the DC output. System connection through the I2C bus reports the performance status of the power supplies within the power shelf. Two Power Shelves can operate in parallel by an optional Shelf-to-Shelf cable, doubling the power output to the maximum capability of 7.2kW for two 12V power shelves.
SELECTION GUIDE
FEATURES
RoHS compliant 1200W (220Vac), 900W (110Vac) Output power 12V Main output, 3.3V or 5V standby output 1U sized; dimensions 12" x 4.75" x 1.6" 13.2 Watts per cubic inch density N+1 redundancy capable, including hot-docking Active current sharing on main output Over-voltage, over-current, over-temperature protection Internal cooling fans IC Bus Interface with status indicators Optional 1U x 19" power-shelf
Part Number
D1U-W-1200-12-HC2C D1U-W-1200-12-HA2C D1U-W-1200-12-HC1C D1U-W-1200-12-HA1C
Power Output High Line AC
1200W 1200W 1200W 1200W
Power Output Low Line AC
900W 900W 900W 900W
Main Output
12V 12V 12V 12V
Standby Output
3.3V 5V 3.3V 5V
Airflow
Back to front Back to front Front to back Front to back
Part Number
S1U-3X-16-A-12-RC
Description
Power shelf for 12V D1U
INPUT CHARACTERISTICS
Parameter
Input Voltage Operating Range Input Frequency Turn-on Input Voltage Turn-off Input Voltage Maximum Input Current Inrush Current Power Factor
Conditions
Low Line AC High Line AC Ramp up Ramp down Low Line AC 90Vac High Line AC 180Vac Cold start between 0-1msec Output load >90% Output load >50%
Min.
90 180 47 78.5 70.5
Typ.
Max.
140 264 63 86.5 78 15 10 100
Units
Vac Hz Vac Arms Apk
50/60
95% 75%
OUTPUT VOLTAGE CHARACTERISTICS
Output Voltage Parameter
Voltage Set Point Accuracy Line and Load Regulation Ripple Voltage & Noise1 Output Current Load Capacitance Voltage Set Point Accuracy Line and Load Regulation Ripple Voltage & Noise1 Operating Range Load Capacitance Voltage Set Point Accuracy Line and Load Regulation Ripple Voltage & Noise1 Operating Range Load Capacitance
Conditions
Min.
11.75
Typ.
12.12
Max.
12.48 120 98.3 40000
Units
Vdc mV p-p A F Vdc mV p-p A F Vdc mV p-p A F
12V
20MHz Bandwidth 0 3.3 3.2 20MHz Bandwidth 0 5 4.85 20MHz Bandwidth 0
3.3Vsb
3.4 33 6 1530 5.15 50 4 1530
5Vsb
1 Ripple and noise are measured with 0.1 uF of ceramic capacitance and 2 x 270 uF of OSCON capacitance on each of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial cable with 50ohm scope termination is used. See Ripple Test Setup diagram.
www.murata-ps.com
Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232
CPS_D1U-W-1200-12-Hx.C06 Page 1 of 7
D1U-W-1200-12-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
OUTPUT CHARACTERISTICS
Parameter
Remote Sense Efficiency Output Rise Monotonicity Start-up Time
Conditions
Min.
Typ.
Max.
Units
mV % s ms mV
Transient Response
120 220Vac 90.6 Overshoot less than 10% for all outputs, no voltage negative between 10% to 95% during ramp up AC ramp up 1.5 PS_On activated 150 12V Ramp 1A/s, 50% load step 600 3.3Vsb Ramp 1A/s, 50% load step 165 5Vsb Ramp 1A/s, 50% load step 250 At 100% load All outputs within regulation Max. load, nominal Vin 10
Current sharing accuracy (up to 6 in parallel) Hot Swap Transients Hold-up Time
%
20
ms
GENERAL CHARACTERISTICS
Parameter
Storage Temperature Range Operating Temperature Range Operating Humidity Storage Humidity Shock Sinusoidal Vibration MTBF Acoustic Safety Approvals Input Fuse Material Flammability Switching Frequency Weight
Conditions
Non-condensing Non-condensing
Min.
-40 0 10 5
Typ.
Max.
70 50 90 90
Units
C %
30G non operating 0.5G, 5 - 500 Hz operating Calculated per Bellcore at Ta=30C 200 Demonstrated 200 ISO 7779-1999 c-CSA-us (CSA 60950-1-03/UL 60950-1, First Edition) TUV approval (Bauart) EN 60950-1:2001
60
Khrs Khrs dB LpAm
Power Supply has internal 20A/250V fast blow fuse on the AC line input UL 94V-0
90KHz for Boost PFC Converter 165KHz for Main Output Converter 200KHz for Standby Output Converter
2.1kg
PROTECTION CHARACTERISTICS
Output Voltage Parameter
Over-temperature Over Voltage Over Current Over Voltage Over Current Over Voltage Over Current
Conditions
Auto-restart Latching Latching Latching Latching Latching Latching
Min.
55 13 107 3.57 6.5 5.6 5
Typ.
Max.
65 14 122 4.02 8 6 7
Units
C V A V A V A
12V 3.3Vsb 5Vsb
ISOLATION CHARACTERISTICS
Parameter
Insulation Safety Rating / Test Voltage Isolation Material Flammability Grounding
Conditions
Min.
Typ.
Max.
Units
Input to Output - Reinforced 3000 Vrms Input to Chassis - Basic 1500 Vrms Output to Chassis Output to Output UL 94V-0 Main Output Return and Standby Output Return are connected internally. 100k resistor parallel with 100nF capacitor is connected between Return and power supply chassis. Main Output Return should be connected to the System Chassis.
www.murata-ps.com
Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232
CPS_D1U-W-1200-12-Hx.C06 Page 2 of 7
D1U-W-1200-12-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
CONTROL SIGNALS
Status
LED
Conditions
Off Flashing Yellow Flashing Green Green Status Output Fault 12V Output 12V Fan1 Monitor Fan2 Monitor
Description
No AC input to all PS Power Supply Failure Main Output Absent Power Supply Good PS-ON, PGOOD, ACOK, PS_BAD, FANFAIL, OT Warning & shutdown, AC Range 12V OV, 12V UV, 12V OC, Vsb Fail, Fan1 Fail, Fan2 Fail 8 bit scaled output voltage 8 bit scaled output current 8 bit scaled output current 8 bit scaled output current
I2C Registers
EMISSIONS AND IMMUNITY
Characteristic
Harmonics Voltage Fluctuation and Flicker Emission Conducted Emission Radiated ESD Electromagnetic Field Electrical Fast Transients/Burst Surge RF Conducted Immunity Magnetic Immunity Voltage dips, interruptions
Description
IEC/EN 61000-3-2 IEC/EN 61000-3-3 FCC 47 CFR Parts 15/CISPR 22/EN55022 FCC 47 CFR Parts 15/CISPR 22/EN55022 IEC/EN 61000-4-2 IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 61000-4-8 IEC/EN 61000-4-11
Criteria
Class A, 6dB margin Class A, 6dB margin 4kV contact discharge 8kV operational air discharge 15kV non-operational air discharge
1kV/2kV, Performance Criteria B 3 Vac, 80% AM, 1kHz, Performance Criteria A 3 A/m
RIPPLE TEST SETUP
0.1uF Ceramic 2x270uF OSCON Power Supply AC Phase
Load Box
AC Ground BNC to BNC Shielded Cable
General Notes: 1. Load the outputs at specified minimum output current. 2. Connect the probe as shown with the input tip and ground as short as possible. 3. Take all measurements 4. Repeat the measurements with the outputs at specified maximum output current.
Oscilloscope 20MHz BW
www.murata-ps.com
Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232
CPS_D1U-W-1200-12-Hx.C06 Page 3 of 7
D1U-W-1200-12-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
OUTPUT CONNECTOR AND SIGNAL SPECIFICATION
DC and Signal Connector: Tyco Part # 1-6450132-2, or FCI PowerBlade # 51732-021
P1 P2 P3 P4 P5 P6 P7 P8 x1 AC_OK x2 P_GOOD x3 V_SB RETURN V_SB RETURN I2C ADR1 x4 V_SB RETURN V_SB RETURN I2C ADR2 I2C CLOCK x5 V_SB +OUT V_SB +OUT PS_KILL x6 V_SB +OUT V_SB +OUT PS_ PRESENT PS_ON D
SPARE VOUT VOUT VRTN VRTN VRTN VRTN VOUT VOUT I_SHARE
SPARE
C
I2C ADR0
B
SENSE +
SENSE -
I2C DATA
SPARE
A
mate-last pins
Pin Assignment
P1, P2, P7, P8 P3, P4, P5, P6 A1 A2 C5, C6, D5, D6 C3, C4, D3, D4 B1 D1 D2 B5 B6 A6 A3 A4 B2 B3 B4
Signal Name
VOUT VRTN Sense + Sense V_SB V_SB Return I_Share AC_OK P_Good PS_Kill PS_Present PS_On I2C Data I2C Clock I2C Adr0 I2C Adr1 I2C Adr2
Description
Main output voltage Main output voltage, return VOUT remote sense, positive node input, connected to the +ve load point VOUT remote sense, negative node input, connected to the -ve load point Standby voltage output Standby voltage, return, tied internally to Output Return Active load sharing bus Input AC Voltage "OK" signal output (Internal pull up is 10k to Vsb) Power good signal output (Internal pull up is 10k to Vsb) Floating pin will turn off P/S (shorter pin, last-make and first-break contact for hot plugging). This signal overrides PS-On in disabling the Main Output Internally tied to Vsb return Internal 1K ohm pull-up to Vsb, (accepts open collector/ drain drive), This signal to be pulled low to turn-on power supply I2C serial data bus I2C serial clock bus Address input 0, internal pull-up to Vsb Address input 1, internal pull-up to Vsb Address input 2, internal pull-up to Vsb
High Level Low Level
I Max
0 - 8V >2.4V (active, OK) <0.4V >2.4V (active, Good) <0.4V >2.1V (open, or Vsb) <0.7V (active, PS:On) 0V >2.1V (open, or Vsb) <0.7V (active, PS:On) Vsb Vsb >2.1V, < Vsb <0.8V >2.1V, 2.1V, -4 mA / +5 mA +4 mA -2 mA +4 mA -2 mA N/A
-4 mA -1 mA
1 mA 1 mA 1 mA
D1U MATING CONNECTORS
12V D1U mating connector
MPS FCI Tyco
2
Press Fit Straight
N/A 51742-10802400CALF TBD N/A 51762-10802400CBLF TBD
Solder 2 Right Angle
N/A 51742-10802400AALF TBD
Straight
Right Angle
36-0430032-0 51762-10802400ABLF TBD
Solder connector recommended for board thickness of <0.090
www.murata-ps.com
Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232
CPS_D1U-W-1200-12-Hx.C06 Page 4 of 7
D1U-W-1200-12-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
CONNECTOR TO CUSTOMER SYSTEM
Signal Connector: MOLEX # 39-28-5204 OR TYCO # 281282-1 Mating Connector: MOLEX # 0039521204 Pin Assignment
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Signal Name
AC_OK11 P_Good12 PS_On13 NOT USED AC_OK01 P_Good02 PS_OnO3 NOT USED I2C Adr2 I C Clock I2C Data4 I_SHARE SENSE +5 SENSE -5 Vsb Vsb Vsb GND GND GND
2 4
Description
Input AC Voltage `OK' signal output for the 2nd shelf Power good signal output for the 2nd shelf Power enable for the 2nd shelf
High Level Low Level
open drain < 0.7V open drain < 0.7V > 2.1V (open, or Vsb) < 0.7V (active, PS:On) open drain < 0.7V open drain < 0.7V > 2.1V (open, or Vsb) < 0.7V (active, PS:On) > 2.1V, < Vsb < 0.8V Vsb Vsb
I Max
- 2 mA + 4 mA - 2 mA + 4 mA - 1 mA - 4 mA - 2 mA + 4 mA - 2 mA + 4 mA - 1 mA - 4 mA 1 mA
Input AC Voltage "OK" signal output for the local shelf Power good signal output for the local shelf Power enable for the local shelf
Address input 2 I C serial clock bus I2C serial data bus
2
Standby voltage output Standby voltage output Standby voltage output GROUND GROUND GROUND
All control signals are with respect to Ground. Negative currents exit the power supply.
1 2 3
Signal goes low when any one of the three power supplies loses AC Signal goes low when any one of the three power supplies fail In a standalone shelf (without I2C control) Pull this pin to GND to turn on three power supplies at the same time. With I2C control, leave this signal float and Use I2C to turn on one power supply at a time. 4 Recomended 10KOhm pull up resistor to host 3.3 or 5V rail 5 Short Sense+ to +Vout and Sens- to GND at the point of load
SHELF TO SHELF CONNECTION
Signal Connector: MOLEX # 39-28-5164 OR TYCO # 281281-1 Pin Assignment
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Signal Name
AC_OK11 P_Good12 PS_On13 NOT USED NOT USED I2C Clock4 I2C Data4 I_SHARE SENSE +5 SENSE -5 Vsb Vsb Vsb GND GND GND
Description
Input AC Voltage `OK' signal output for the 2nd shelf Power good signal output for the 2nd shelf Power enable for the 2nd shelf
High Level Low Level
open drain < 0.7V open drain < 0.7V > 2.1V (open, or Vsb) < 0.7V (active, PS:On)
I Max
- 2 mA + 4 mA - 2 mA + 4 mA - 1 mA - 4 mA
I2C serial clock bus I2C serial data bus
Vsb Vsb
Standby voltage output Standby voltage output Standby voltage output GROUND GROUND GROUND
www.murata-ps.com
Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232
CPS_D1U-W-1200-12-Hx.C06 Page 5 of 7
D1U-W-1200-12-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
MECHANICAL DIMENSIONS - D1U-W-1200-12-Hx
20,20 0,40 [ 0.795 0.015 ] 312,89 0,35 [ 12.318 0.013 ] 8,89 [ 0.350 ] REF 37,30 0,40 [ 1.468 0.015 ]
132,85 0,50 [ 5.230 0.019 ] 127,85 0,40 [ 5.033 0.015 ] 120,65 0,65 [ 4.750 0.025 ]
304,80 0,65 [ 12.000 0.025 ]
12,63 0,40 [ 0.497 0.015 ]
41.00040 [1.6140.015]
AC Input Connector: The AC input connector is standard IEC320 C14 (15A).
Dimensions: 12.00"L x 4.75" W x 1.6" H (40.7H x 120.6W x 304.90mm)
MECHANICAL DIMENSIONS - S1U Power Shelf
17.315 (439.80)
1.252 (31.80)
15.937 (404.80)
18.307 (465.00) 18.992 (482.40)
NOTES: 1. The DC output terminals are of terminal block style that will allow connection using crimp type right-angle lugs accepting up to AWG#2 wire, Panduit lug LCC2-14AWF-Q or equivalent is recommended. 2. Two M6 studs at 15.88 mm centre spacing are provided for connection to each pole. Hardware is provided for fastening the lugs/wires as well as terminal block covers
1.709 (43.40) 0.228 (5.80)
www.murata-ps.com
Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232
CPS_D1U-W-1200-12-Hx.C06 Page 6 of 7
D1U-W-1200-12-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
S1U PIN CONNECTORS - BACK VIEW
12V+ OUTPUT
PIN #1 PIN #1
12V+ OUTPUT
GND
GND J2 SIGNAL CONNECTOR FOR SHELF-TO-SHELF CONNECTION USE CABLE P/N 535-413-1537-1 J1 SIGNAL CONNECTOR TO CUSTOMER SYSTEM
SHELF TO SHELF CONNECTION
J1 SIGNAL CONNECTOR TO CUSTOMER SYSTEM J2 TO J1 RIBBON CABLE P/N 535-413-1537-1
( REPEAT THIS CONNECTION FOR ADDITIONAL SHELVES. )
OPTIONAL ACCESSORIES
Description
12V D1U output connector card Shelf to shelf cable
Part Number
D1U-12-CONC 535-413-1537-1
APPLICATION NOTES
Document Number
ACAN-27 ACAN-29
Description
Output Connector Card D1U Communication Protocol
USA: Canada: UK: France: Germany: Japan: China: Singapore:
Mansfield (MA), Tel: (508) 339-3000, email: sales@murata-ps.com Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com Munchen, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com
Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232
Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356
www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED
01/22/09
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. (c) 2009 Murata Power Solutions, Inc.
www.murata-ps.com
CPS_D1U-W-1200-12-Hx.C06 Page 7 of 7

▲Up To Search▲

Price & Availability of D1U-W-1200-12-HA1C

	To Download D1U-W-1200-12-HA1C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .