 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TA8200AH TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic TA8200AH Dual Audio Power Amplifier The TA8200AH is dual audio power amplifier for consumer applications. This IC provides an output power of 13 watts per channel (at VCC = 28 V, f = 1 kHz, THD = 10%, RL = 8 ). It is suitable for power amplifier of TV and home stereo. Features * * High output power: Pout = 13 W/channel (Typ.) (VCC = 28 V, RL = 8 , f = 1 kHz, THD = 10%) Low noise: Vno = 0.14 mVrms (Typ.) (VCC = 28 V, RL = 8 , GV = 34dB, Rg = 10 k, BW = 20 Hz~20 kHz) * * * * Very few external parts Built in audio muting circuit Built in thermal shut down protector circuit Operating supply voltage range: VCC (opr) = 10~37 V (Ta = 25C) Weight: 4.04 g (typ.) 1 2002-02-13 TA8200AH Block Diagram VCC 6 Ripple Filter 9 VCC IN1 IN1 4 AMP1 5 3 1 OUT1 7 RL 400 W Pre-GND 400 W 20 kW PW-GND 10 20 kW AMP2 12 RL OUT2 IN2 2 IN2 8 11 Application Information 1. Voltage gain The closed loop voltage gain is determined by R1, R2. GV R + R2 = 20 log 1 (dB) R2 20 kW + 400 W = 20log = 34(dB) 400 W Input 4/2 5/1 R2 400 W R1 20 kW 7/12 Output = 34 (dB) Amplifier with gain < 34dB G V = 20 log R1 + R 2 + R 3 (dB) R2 + R3 Figure 1 When R3 = 220 W GV ~ 30 (dB) is given. Input 4/2 R3 5/1 R2 400 W R1 20 kW 7/12 Output Figure 2 2 2002-02-13 TA8200AH 2. Muting (1) Audio muting This IC is possible to make audio muting operation by using 11 pin muting terminal. In Fig. 3, the equivalent circuit in the muting circuit section is shown. By means of reducing the voltage of 11 pin down to 2.8 V or less in Fig. 3, Q1 is turned ON and the base voltage of Q2 in the differential circuit fabricated with Q2 and Q3. Therefore, with the voltage reduction of 11 pin, the input circuits of dummy of input terminal and that in the doted line operate and cut-off the input signal. After muting, the bias circuit continues is operation and the power supply current of quiescent time. 8 pin, the capacitor terminal for reducing the pop noise can reduce the pop noise through making the time constant longer by means of inserting the capacitor externary. In the care this terminal is not used, short 8 pin with 11 pin. The voltage of 11 pin set up to 4 V or more. IC internal muting at VCC OFF When VCC = 8 V or less at VCC off, the detection circuit at VCC off is operated. And the base voltage of Q1 is reduced and the muting operation is mode. (2) 9 Reference voltage The detection circuit at VCC (R) OFF Q1 100 W 1 kW Q2 Q3 I1 I2 I3 I4 I5 I6 VCC Q6 D1 D2 Q4 Q5 20 kW 7/12 OUT 11 Mute 8 2/4 IN Figure 3 Cautions This IC is not proof enough against a strong E-M field by CRT which may cause malfunction such as leak. Please set the IC keeping the distance from CRT. 400 W 1/5 NF 3 2002-02-13 TA8200AH Standard PCB (Bottom view) 4 2002-02-13 TA8200AH Maximum Ratings (Ta = 25C) Characteristics Supply voltage Output current (Peak/ch) Power dissipation Operating temperature Storage temperature Symbol VCC IO (peak) PD (Note) Topr Tstg Rating 37 2.5 25 -20~75 -55~150 Unit V A W C C Note: Derated above Ta = 25C in the proportion of 200 mW/C. Electrical Characteristics Characteristics Quiescent current Output power Total harmonic distortion Voltage gain Input resistance Ripple rejection ratio Output noise voltage Cross talk Muting threshold voltage (unless otherwise specified, VCC = 28 V, RL = 8 9, Rg = 600 9, f = 1 kHz, Ta = 25C) Symbol ICCQ Pout (1) Pout (2) THD GV RIN R.R. Vno C.T. Vth 11 Test Circuit 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 Vin = 0 THD = 10% THD = 1% Pout = 2 W Vout = 0.775 Vrms (0dBm) 3/4 Rg = 0, fripple = 100 Hz Vripple = 0.775 Vrms (0dBm) Rg = 10 kW, BW = 20 Hz~20 kHz Rg = 10 kW, Vout = 0.775 Vrms (0dBm) 3/4 Test Condition Min 3/4 10 3/4 3/4 32.5 3/4 -40 3/4 3/4 2.6 Typ. 50 13 10 0.04 34.0 30 -50 0.14 -70 2.8 Max 105 3/4 3/4 0.2 35.5 3/4 3/4 0.3 3/4 3/4 Unit mA W % dB kW dB mVrms dB V Typ. DC Voltage of Each Terminal (VCC = 28 V, Ta = 25C) Terminal No. DC voltage (V) 1 1.6 2 20m 3 GND 4 20m 5 1.6 6 9.4 7 13.0 8 5.0 9 VCC 10 GND 11 2.8 12 13.0 5 2002-02-13 TA8200AH Test Circuit 47 mF 1000 mF VCC 6 Ripple Filter IN1 2.2 mF 47 mF 47 mF 4 IN1 AMP1 5 3 1 400 W Pre-GND 400 W 20 kW AMP2 2.2 mF 2 IN2 20 kW 9 OUT1 2.2 W 7 1000 mF RL PW-GND 10 2.2 W 0.12 mF 0.12 mF RL IN2 OUT2 12 1000 mF 8 *2 11 *1 Vth ~ 2.8 V - *1: Mute on at 11 pin low Vth 11 = 2.8 V (typ.) (VCC = 28 V, Ta = 25C) *2: The capacitor for reducing POP noise at mute ON. 6 2002-02-13 TA8200AH THD - Pout 20 THD - Pout 20 (%) (%) 10 5 3 VCC = 28 V RL = 8 W 10 5 3 f = 1 kHz RL = 8 W THD THD VCC = 22 V 28 1 0.5 0.3 37 Total harmonic distortion 1 0.5 0.3 f = 10 kHz 0.1 0.05 0.03 0.1 0.3 0.5 1 3 5 10 30 50 100 100 Hz 1 kHz Total harmonic distortion 0.1 0.05 0.03 0 0.1 0.3 0.5 1 3 5 10 30 50 100 Output power Pout (W) Output power Pout (W) THD - f 5 80 VCC = 28 V Pout = 1 W RL = 8 W 70 3 GV - f VCC = 28 V f = 1 kHz RL = 8 W (%) THD Total harmonic distortion 0.3 Gv Voltage gain 30 50 100 300 500 1k 3k 5k 10k 30k 50k 100k 0.5 (dB) 1 60 50 40 30 20 10 0.1 0.05 0.03 0.01 0 30 50 100 300 500 1k 3k 5k 10k 30k 50k 100k Frequency f (Hz) Frequency f (Hz) R.R. - f 0 -10 -20 -30 -40 -50 -60 -70 -80 VCC = 28 V RL = 8 W Rg = 0 W Vripple = 0.775 Vrms (0dBm) 0 -10 -20 -30 -40 -50 -60 -70 -80 R.R. - Rg VCC = 28 V RL = 8 W Vripple = 0.775 Vrms (0dBm) fripple = 100 Hz Ripple rejection ratio R.R. (dB) 30 50 100 300 500 1k 3k 5k 10k 30k 50k 100k Ripple rejection ratio R.R. (dB) 30 50 100 300 500 1k 3k 5k 10k 30k 50k 100k Frequency f (Hz) Signal source resistance Rg (W) 7 2002-02-13 TA8200AH C.T. - f 0 -10 VCC = 28 V f = 1 kHz Vout = 0.775 Vrms (0dBm) RL = 8 W Rg = 10 kW 0 -10 C.T. - Rg VCC = 28 V f = 1 kHz RL = 8 W Vout = 0.775 Vrms (0dBm) C.T. (dB) -30 -40 -50 -60 -70 -80 C.T. (dB) Cross talk -20 -20 -30 -40 -50 -60 -70 -80 Cross talk 30 50 100 300 500 1k 3k 5k 10k 30k 50k 100k 30 50 100 300 500 1k 3k 5k 10k 30k 50k 100k Frequency f (Hz) Signal source resistance Rg (W) Vno - Rg 1.6 24 VCC = 28 V RL = 8 W f = 1 kHz RL = 8 W/4 W THD = 10 % Pout - VCC (mVrms) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 20 Pout (W) Output power Output noise voltage Vno 16 12 RL = 4 W 8 8 4 30 50 100 300 500 1k 3k 5k 10k 30k 50k 100k 0 10 14 18 22 26 30 34 38 42 Signal source resistance Rg (W) Supply voltage VCC (V) ICCQ, VOUT - VCC 240 Vin = 0 32 VCC = 28 V f = 1 kHz Pout = 2 W RL = 8 W DUAL Ope. THD - Ta Heat sink 80 80 2 mm A (7C/W) ICCQ (mA) (V) (%) Total harmonic distortion THD 0.2 0.1 0.05 0.03 0.01 -40 Quiescent current 120 16 VOUT 60 ICCQ 8 0 0 Output DC voltage VOUT 180 24 8 16 24 32 40 -20 0 20 40 60 80 100 Supply voltage VCC (V) Ambient temperature Ta (C) 8 2002-02-13 TA8200AH ICCQ - Ta (mVrms) 80 Heat sink 80 80 2 mm A (7C/W) VCC = 28 V RL = 8 W 0.5 Vno - Ta Heat sink 80 80 2 mm A (7C/W) VCC = 28 V RL = 8 W Rg = 10 kW ICCQ (mA) 70 0.4 50 Output noise volltage Quiescent current 60 Vno 0.3 0.2 40 0.1 30 -40 -20 0 20 40 60 80 100 0 -40 -20 0 20 40 60 80 100 Ambient temperature Ta (C) Ambient temperature Ta (C) PD - Pout (W) 24 24 PD MAX - VCC f = 1kHz RL = 8 W 20 Maximum power dissipation PD MAX 32 (W) VCC = 37 V THD = 1% 10% 20 PD 16 16 Power dissipation 12 28 V 23 V f = 1kHz RL = 8 W DUAL OPE. 4 8 12 16 20 24 28 12 8 8 4 4 0 0 0 8 12 16 20 24 28 32 36 40 Output power Pout (W) Supply voltage VCC (V) PD MAX - Ta (W) 30 1: Infinite heat sink 25 1 2: 4.1C/W heat sink 3: 9.5C/W heat sink Allowable power dissipation PD MAX 20 2 15 3 10 5 0 0 25 50 75 100 125 150 175 Ambient temperature Ta (C) 9 2002-02-13 TA8200AH Package Dimensions Weight: 4.04 g (typ.) 10 2002-02-13 TA8200AH RESTRICTIONS ON PRODUCT USE 000707EBF * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * This product generates heat during normal operation. However, substandard performance or malfunction may cause the product and its peripherals to reach abnormally high temperatures. The product is often the final stage (the external output stage) of a circuit. Substandard performance or malfunction of the destination device to which the circuit supplies output may cause damage to the circuit or to the product. * The products described in this document are subject to the foreign exchange and foreign trade laws. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. * The information contained herein is subject to change without notice. 11 2002-02-13 |
Price & Availability of TA8200AH02
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |