 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 74ALVCR162245 LOW VOLTAGE CMOS 16-BIT TRANSCEIVER (3-STATE) WITH 3.6V TOLERANT INPUTS AND OUTPUTS I I 3.6V TOLERANT INPUTS AND OUTPUTS HIGH SPEED: tPD = 3.0 ns (MAX.) at VCC = 3.0 to 3.6V tPD = 3.7 ns (MAX.) at VCC = 2.3 to 2.7V tPD =6 ns (MAX.) at VCC = 1.65V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 12mA (MIN) at VCC = 3.0V |IOH| = IOL = 6mA (MIN) at VCC = 2.3V |IOH| = IOL = 2mA (MIN) at VCC = 1.65V OPERATING VOLTAGE RANGE: VCC(OPR) = 1.65V to 3.6V 26 SERIE RESISTORS IN BOTH A AND B PORT OUTPUTS PIN AND FUNCTION COMPATIBLE WITH 74 SERIES R162245 LATCH-UP PERFORMANCE EXCEEDS 300mA (JESD 17) ESD PERFORMANCE: HBM > 2000V (MIL STD 883 method 3015); MM > 200V TSSOP I I Table 1: Order Codes PACKAGE TSSOP T&R 74ALVCR162245TTR I I Figure 1: Pin Connection I I I DESCRIPTION The 74ALVCR162245 is a low voltage CMOS 16 BIT BUS TRANSCEIVER fabricated with sub-micron silicon gate and five-layer metal wiring C2MOS technology. It is ideal for low power and very high speed 1.65 to 3.6V applications; it can be interfaced to 3.6V signal environment for both inputs and outputs. This IC is intended for two-way asynchronous communication between data busses; the direction of data transmission is determined by DIR input. The enable input G can be used to disable the device so that the busses are effectively isolated. Bus hold on data inputs is provided in order to eliminate the need for external pull-up or pull-down resistor. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. February 2005 Rev. 1 1/11 74ALVCR162245 Figure 2: Input And Output Equivalent Circuit Table 2: Pin Description PIN N 1 2, 3, 5, 6, 8, 9, 11, 12 13, 14, 16, 17, 19, 20, 22, 23 24 25 36, 35, 33, 32, 30, 29, 27, 26 47, 46, 44, 43, 41, 40, 38, 38 48 4, 10, 15, 21, 28, 34, 39, 45 7, 18, 31, 42 SYMBOL NAME AND FUNCTION Figure 3: IEC Logic Symbols 1DIR Directional Control 1B1 to 1B8 Data Inputs/Outputs 2B1 to 2B8 Data Inputs/Outputs 2DIR Directional Control 2G Output Enable Input 2A1 to 2A8 Data Inputs/Outputs 1A1 to 1A8 Data Inputs/Outputs 1G GND VCC Output Enable Input Ground (0V) Positive Supply Voltage Table 3: Truth Table INPUTS G L L H DIR L H X FUNCTION A BUS B BUS OUTPUT Yn A=B B=A Z OUTPUT INPUT INPUT OUTPUT Z Z Z : High Impedance X : Don`t Care 2/11 74ALVCR162245 Table 4: Absolute Maximum Ratings Symbol VCC VI VO VO IIK IOK IO Supply Voltage DC Input Voltage DC Output Voltage (OFF State) DC Output Voltage (High or Low State) (note 1) DC Input Diode Current DC Output Diode Current (note 2) DC Output Current Parameter Value -0.5 to +4.6 -0.5 to +4.6 -0.5 to +4.6 -0.5 to VCC + 0.5 - 50 - 50 50 100 400 -65 to +150 300 Unit V V V V mA mA mA mA mW C C ICC or IGND DC VCC or Ground Current per Supply Pin Power Dissipation PD Tstg TL Storage Temperature Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) IO absolute maximum rating must be observed 2) VO < GND, VO > VCC Table 5: Recommended Operating Conditions Symbol VCC VI VO VO IOH, IOL IOH, IOL IOH, IOL Top dt/dv Supply Voltage Input Voltage Output Voltage (OFF State) Output Voltage (High or Low State) High or Low Level Output Current (VCC = 3.0 to 3.6V) High or Low Level Output Current (VCC = 2.3 to 2.7V) High or Low Level Output Current (VCC = 1.65V) Operating Temperature Input Rise and Fall Time (note 1) Parameter Value 1.65 to 3.6 -0.3 to 3.6 0 to 3.6 0 to VCC 12 6 2 -55 to 125 0 to 10 Unit V V V V mA mA mA C ns/V 1) VIN from 0.8V to 2V at VCC = 3.0V 3/11 74ALVCR162245 Table 6: DC Specifications Test Condition Symbol Parameter VCC (V) 1.65 to 1.95 2.3 to 2.7 2.7 to 3.6 1.65 to 1.95 2.3 to 2.7 2.7 to 3.6 1.65 to 3.6 1.65 2.3 2.3 3.0 2.7 3.0 VOL Low Level Output Voltage 1.65 to 3.6 1.65 2.3 2.3 3.0 2.7 3.0 II Ioff IOZ Input Leakage Current Power Off Leakage Current High Impedance Output Leakage Current Quiescent Supply Current ICC incr. per Input 3.6 0 3.6 IO=-100 A IO=-2 mA IO=-4 mA IO=-6 mA IO=-6 mA IO=-8 mA IO=-12 mA IO=100 A IO=2 mA IO=4 mA IO=6 mA IO=6 mA IO=8 mA IO=12 mA VI = 0 or 3.6V VI or VO = 3.6V VI = VIH or VIL VO = 0 to VCC VI = VCC or GND IO= 0 VIH = VCC - 0.6V -40 to 85 C Min. 0.65 Vcc 1.7 2.0 0.35 Vcc 0.7 0.8 VCC-0.2 1.2 1.9 1.7 2.4 2.0 2.0 0.2 0.45 0.4 0.55 0.55 0.6 0.8 5 10 5 VCC-0.2 1.2 1.9 1.7 2.4 2.0 2.0 0.2 0.45 0.4 0.55 0.55 0.6 0.8 5 20 10 A A A A A V V Max. Value -55 to 125 C Min. 0.65 Vcc 1.7 2.0 0.35 Vcc 0.7 0.8 Max. Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage VIL V VOH ICC ICC 3.6 3.0 to 3.6 20 500 40 750 4/11 74ALVCR162245 Table 7: AC Electrical Characteristics Test Condition Symbol Parameter VCC (V) 1.65 to 1.95 2.3 to 2.7 2.7 3.0 to 3.6 1.65 to 1.95 2.3 to 2.7 2.7 3.0 to 3.6 1.65 to 1.95 2.3 to 2.7 2.7 3.0 to 3.6 CL (pF) 30 30 50 50 30 30 50 50 30 30 50 50 RL () 500 500 500 500 500 500 500 500 500 500 500 500 ts = tr (ns) 2.0 2.0 2.5 2.5 2.0 2.0 2.5 2.5 2.0 2.0 2.5 2.5 -40 to 85 C Min. 1 1 1 1 1 1 1 1 1 1 1 1 Max. 8.6 4.3 4.8 3.9 9.8 5.7 6.2 4.7 8.6 4.8 5.3 4.6 Value -55 to 125 C Min. 1 1 1 1 1 1 1 1 1 1 1 1 Max. 8.6 4.3 4.8 3.9 9.8 5.7 6.2 4.7 8.6 4.8 5.3 4.6 Unit tPLH tPHL Propagation Delay Time tPZL tPZH Output Enable Time ns tPLZ tPHZ Output Disable Time 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|) 2) Parameter guaranteed by design Table 8: Capacitive Characteristics Test Condition Symbol Parameter VCC (V) 3.3 3.3 3.3 2.5 3.3 2.5 VIN =VCC or GND VIN =VCC or GND fIN = 10MHz CL=50pF VIN = 0 or VCC Value TA = 25 C Min. Typ. 4 8 29 22 5 4 Max. pF pF Unit CIN CI/O CPD CPD Input Capacitance Control Inputs Input Capacitance A or B ports Power Dissipation Capacitance Output enabled (note 1) Power Dissipation Capacitance Output disabled (note 1) pF 1) CPD is defined as the value of the IC's internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/16 (per circuit) 5/11 74ALVCR162245 Figure 4: Test Circuit TEST tPLH, tPHL tPZL, tPLZ (VCC = 3.0 to 3.6V) tPZL, tPLZ (VCC = 2.3 to 2.7V) tPZH, tPHZ RT = ZOUT of pulse generator (typically 50) SWITCH Open 6V 2VCC GND Table 9: Test Circuit And Waveform Symbol Value Symbol 3.0 to 3.6V VIH VM VX VY CL RL=R1 tr = tr 2.7V 1.5V VOL +0.3V VOH -0.3V 50pF 500 <2.5ns 2.7V 2.7V 1.5V VOL +0.3V VOH -0.3V 50pF 500 <2.5ns VCC 2.3 to 2.7V VCC VCC/2 VOL +0.15V VOH -0.15V 30pF 500 <2.0ns 1.65 to 1.95V VCC VCC/2 VOL +0.15V VOH -0.15V 30pF 1000 <2.0ns 6/11 74ALVCR162245 Figure 5: Waveform - Propagation Delays (f=1MHz; 50% duty cycle) Figure 6: Waveform - Output Enable And Disable Time (f=1MHz; 50% duty cycle) 7/11 74ALVCR162245 TSSOP48 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0 0.45 6.0 0.5 BSC 8 0.75 0 0.018 0.17 0.09 12.4 8.1 BSC 6.2 0.236 0.0197 BSC 8 0.030 0.05 0.9 0.27 0.20 12.6 0.0067 0.0035 0.488 0.318 BSC 0.244 TYP MAX. 1.2 0.15 0.002 0.035 0.011 0.0079 0.496 MIN. TYP. MAX. 0.047 0.006 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 7065588D 8/11 74ALVCR162245 Tape & Reel TSSOP48 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 8.7 13.1 1.5 3.9 11.9 12.8 20.2 60 30.4 8.9 13.3 1.7 4.1 12.1 0.343 0.516 0.059 0.153 0.468 TYP MAX. 330 13.2 0.504 0.795 2.362 1.197 0.350 0.524 0.067 0.161 0.476 MIN. TYP. MAX. 12.992 0.519 inch 9/11 74ALVCR162245 Table 10: Revision History Date 25-Feb-2005 Revision 1 First Release. Description of Changes 10/11 74ALVCR162245 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners (c) 2005 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 11/11 |
Price & Availability of 74ALVCR162245TTR
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |