 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DATA SHEET NEC's L, S-BAND SPDT SWITCH UPG168TB FEATURES * SWITCH CONTROL VOLTAGE: Vcont (H) = 2.5 to 5.3 V (3.0 V TYP.) Vcont (L) = -0.2 to +0.2 V (0 V TYP.) LOW INSERTION LOSS: LINS1 = 0.30 dB TYP. @ f = 0.5 to 1.0 GHz, Vcont = 3.0 V/0 V LINS2 = 0.40 dB TYP. @ f = 2.0 GHz, Vcont = 3.0 V/0V LINS3 = 0.90 dB MAX. @ f = 2.0 to 2.5 GHz, Vcont = 3.0 V/0 V HIGH ISOLATION: ISL1 = 27 dB TYP. @ f = 0.5 to 2.0 GHz, Vcont = 3.0 V/0 V ISL2 = 18 dB MIN. @ f = 2.0 to 2.5 GHz, Vcont = 3.0 V/0 V * MIDDLE POWER: Pin (1 dB) = +26.5 dBm TYP. @ f = 1.0 GHz, Vcont = 3.0 V/0 V * HIGH-DENSITY SURFACE MOUNTING: 6-pin super minimold package (2.0 x 1.25 x 0.9 mm) DESCRIPTION NEC's UPG168TB is GaAs MMIC for L, S-band SPDT (Single Pole Double Throw) switch which were developed for mobile phone and another L, S-band application. This device can operate frequency from 0.5 to 2.5 GHz, having the low insertion loss and high isolation. This device is housed in a 6-pin super minimold package. And this package is able to high-density surface mounting. * * APPLICATION * L-band digital cellular or cordless telephone * PCS, W-LAN, WLL and BluetoothTM etc. ORDERING INFORMATION PART NUMBER UPG168TB-E4 PACKAGE 6-pin super minimold MARKING G2T SUPPLYING FORM * Embossed tape 8 mm wide * Pin 4, 5, 6 face the perforation side of the tape * Qty 3 kpcs/reel Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: UPG168TB Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. California Eastern Laboratories UPG168TB PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM (Top View) 1 2 3 61 52 43 (Top View) 66 55 44 (Bottom View) 1 2 3 PIN NO. 1 2 3 4 5 6 PIN NAME OUTPUT2 GND OUTPUT1 Vcont1 INPUT V cont2 TRUTH TABLE Vcont1 Low High Vcont2 High Low INPUT-OUTPUT1 ON OFF INPUT-OUTPUT2 OFF ON ABSOLUTE MAXIMUM RATINGS (TA =+25C, unless otherwise specified) PARAMETER Switch Control Voltage Input Power Power Dissipation Operating Ambient Temperature Storage Temperature SYMBOL Vcont Pin PD TA Tstg RATINGS -6.0 to +6.0 Note 1 +28 150 Note 2 -45 to +85 -55 to +150 UNIT V dBm mW C C Notes 1. Mounted on double-sided copper-clad 50 x 50 x 1.6 mm epoxy glass PWB, TA = +85C 2. | Vcont1 - Vcont2 | 6.0 V RECOMMENDED OPERATING RANGE (TA =+25C, unless otherwise specified) PARAMETER Switch Control Voltage (H) Switch Control Voltage (L) SYMBOL Vcont (H) Vcont (L) MIN. 2.5 -0.2 TYP. 3.0 0 MAX. 5.3 0.2 UNIT V V G2T UPG168TB ELECTRICAL CHARACTERISTICS (TA = +25C, Vcont = 3.0 V/0 V, DC blocking capacitors = 51 pF, unless otherwise specified) PARAMETER Insertion Loss 1 Insertion Loss 2 Insertion Loss 3 Isolation 1 Isolation 2 Input Return Loss 1 Input Return Loss 2 Output Return Loss 1 Output Return Loss 2 1 dB Gain Compression Input Power Note Switch Control Speed Switch Control Current SYMBOL LINS1 LINS2 LINS3 ISL1 ISL2 RLin1 RLin2 RLout1 RLout2 Pin (1 dB) tSW Icont TEST CONDITIONS f = 0.5 to 1.0 GHz f = 2.0 GHz f = 2.0 to 2.5 GHz f = 0.5 to 2.0 GHz f = 2.0 to 2.5 GHz f = 0.5 to 2.0 GHz f = 2.0 to 2.5 GHz f = 0.5 to 2.0 GHz f = 2.0 to 2.5 GHz f = 1.0 GHz MIN. - - - 22 18 13 11 13 11 +22.0 - - TYP. 0.30 0.40 - 27 - 19 - 19 - +26.5 50 0.5 MAX. 0.55 0.65 0.90 - - - - - - - 200 10 UNIT dB dB dB dB dB dB dB dB dB dBm ns A Note Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear range. STANDARD CHARACTERISTICS FOR REFERENCE (TA = +25C, Vcont = 3.0 V/0 V, DC cut capacitors = 51 pF, unless otherwise specified) PARAMETER 0.1 dB Gain Compression Input Power Note SYMBOL Pin (0.1 dB) TEST CONDITIONS f = 1.0 GHz MIN. - TYP. +23.0 MAX. - UNIT dBm Note Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear range. Caution This device is used it is necessary to use DC cut capacitors. The value of DC blocking capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with actual board of your system. The range of recommended DC cut capacitor value is less than 100 pF. UPG168TB EVALUATION CIRCUIT (Vcont = 3.0 V/0 V, DC blocking capacitors = 51 pF) Vcont2 INPUT Vcont1 1000 pF 6 51 pF 1000 pF 4 5 1 2 3 51 pF 51 pF OUTPUT2 OUTPUT1 This application circuit and its parameters are for reference only. UPG168TB ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD VDD 6Pin SMM SPDT SW VC 1 OUTPUT1 OUT 1 C2 C 1 C 5 C1 C1 G2T INPUT IN C3 C1 C 4 C 2 C2 OUT 2 OUTPUT2 VC 2 Vcont USING THE NEC EVALUATION BOARD SYMBOL C1, C2, C3 C4, C5 VALUES 51 pF 1000 pF UPG168TB PACKAGE DIMENSIONS 6-PIN SUPER MINIMOLD (UNIT:mm) 2.10.1 1.250.1 2.00.2 1.3 0.65 0.65 0.1 MIN. 0.90.1 0.7 0 to 0.1 0.15+0.1 -0.05 0.2+0.1 -0.05 UPG168TB RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220C or higher Preheating time at 120 to 180C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Peak temperature (package surface temperature) Time at temperature of 200C or higher Preheating time at 120 to 150C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Peak temperature (molten solder temperature) Time at peak temperature Preheating temperature (package surface temperature) Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Peak temperature (pin temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260C or below : 10 seconds or less : 60 seconds or less : 12030 seconds : 3 times : 0.2%(Wt.) or below : 215C or below : 25 to 40 seconds : 30 to 60 seconds : 3 times : 0.2%(Wt.) or below : 260C or below : 10 seconds or less : 120C or below : 1 time : 0.2%(Wt.) or below : 350C or below : 3 seconds or less : 0.2%(Wt.) or below Condition Symbol IR260 VPS VP215 Wave Soldering WS260 Partial Heating HS350 Caution Do not use different soldering methods together (except for partial heating). Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 03/15/2005 A Business Partner of NEC Compound Semiconductor Devices, Ltd. |
Price & Availability of UPG168TB-E4
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |