View RDR-131_1301024.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Title
Reference Design Report for 3 W NonIsolated Constant Current LED Driver Using LNK306DN
Specification 85-265 VAC Input, 10 V, 300 mA Output Application Author Document Number Date Revision LED Lighting / Bulb Retrofit Power Integrations Applications Department RDR-131 March 7, 2007 1.1
Summary and Features * * * * * * * Extremely small form factor, fits within GU10 lamp base Operates over the universal input voltage range (85 - 265 VAC) Meets EN55022 B conducted EMI requirements Drives LEDs in constant current (CC) mode Built-in, output overvoltage protection when unloaded * Allows supply to be tested without the load connected Low parts count, low-cost solution: only 25 components Non-isolated buck converter configuration allows use of off-the-shelf inductors (does not require a custom transformer)
The products and applications illustrated herein (including circuits external to the products and transformer construction) may be covered by one or more U.S. and foreign patents or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A complete list of Power Integrations' patents may be found at www.powerint.com.
Power Integrations 5245 Hellyer Avenue, San Jose, CA 95138 USA. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
Table of Contents
Introduction...............................................................................................................3 Power Supply Specification ......................................................................................5 Circuit Diagram.........................................................................................................6 Circuit Description ....................................................................................................7 4.1 Configuration and Assembly Details..................................................................7 4.2 AC Input Rectification ........................................................................................7 4.3 LinkSwitch-TN ...................................................................................................7 4.4 Output Feedback...............................................................................................7 5 Bill of Materials .......................................................................................................10 5.1 Filter Board Bill of Materials.............................................................................10 5.2 Converter Board Bill of Materials.....................................................................11 6 PI Xls Design Spreadsheet.....................................................................................12 7 Performance ...........................................................................................................14 7.1 Efficiency .........................................................................................................14 7.2 Output Current Regulation Vs. Line Voltage....................................................15 7.3 Output VI Characteristic ..................................................................................15 8 Waveforms .............................................................................................................16 8.1 Drain Voltage and Current, Normal Operation.................................................16 8.2 Output Current and Voltage.............................................................................16 8.3 Drain Current and Bulk Capacitor Voltage.......................................................17 8.4 Startup Drain Current and Bulk Capacitor Voltage ..........................................17 8.5 Startup Output Voltage and Current ................................................................18 8.6 Fault Conditions ..............................................................................................18 9 Thermal Measurements..........................................................................................19 10 Conducted EMI.......................................................................................................20 10.1 Competitive Product EMI.................................................................................21 11 Revision History......................................................................................................22 1 2 3 4
Important Note: This board has no safety isolation. Therefore, all testing should be performed using an isolation transformer to provide the AC input to the prototype board.
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 2 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
1 Introduction
This engineering report describes an LED driver power supply that uses a member of the LinkSwitch-TN family of devices, the LNK306DN. The circuit regulates its load current to 300 mA while developing about 10 V across three series HB-LEDs. The design provides no safety isolation between the AC input and DC output. Therefore the enclosure must be designed to provide isolation. The report contains the power supply specification, a circuit diagram, a complete bill of materials, the PI Xls spreadsheet results for the design, the printed circuit board layouts, and performance data.
Figure 1 - Photographs of (Top and Side views) Populated Circuit Board Assembly.
Page 3 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
Figure 2 - Mechanical Positioning of the Power Supply Assembly Inside the GU10 Bulb Socket Base.
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 4 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
2 Power Supply Specification
Description Input Voltage Frequency No-load Input Power (230 VAC) Output Output Voltage 1 Output Current 1 Total Output Power Continuous Output Power Efficiency Environmental Conducted EMI Safety Ambient Temperature TAMB Meets EN55022B/CISPR22B No input to output isolation 0 40
o
Symbol VIN fLINE
Min 85 47
Typ
Max 265 64 -
Units VAC Hz W V A
Comment
2 Wire - no P.E. Not applicable 10% at 25 C
o
50/60
VOUT1 IOUT1 POUT
10 0.3 3 62
W %
Measured at POUT (3 W), 25 C
o
C
Free convection, sea level
Page 5 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
3 Circuit Diagram
Figure 3a - Circuit Diagram of Filter Board.
Figure 3b - Circuit Diagram of Converter Board.
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 6 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
4 Circuit Description
4.1 Configuration and Assembly Details The power supply is configured as a non-isolated buck converter. Since it must fit in a GU10 lamp socket base, the supply was split into 2 interconnected boards. A Faraday shield (the third board) was sandwiched between the input rectification/EMI filter (bottom) board and the converter (top) board. The shield board is electrically connected to the converter board. This was necessary to meet the conducted EMI requirements. The shield consists of a single-sided, copper-clad PCB that is the same size as the input rectification/EMI filter board. 4.2 AC Input Rectification A 10 fusible resistor (RF1) will act as a fuse if a catastrophic failure occurs. The input voltage and current are rectified by a bridge rectifier (BR1) and smoothed by a pi filter circuit (C1, L1 and C2). The pi filter and RF1 also help attenuate the differential mode conducted EMI that is generated by the switching of the buck converter. 4.3 LinkSwitch-TN The PI Xls spreadsheet tool was used to design this converter. When powering the designated LED load, the converter operates in the continuous conduction mode (CCM). The buck converter stage consists of the integrated MOSFET switch within the LNK306DN (U1), a freewheeling diode (D3), an output inductor (L2) and an output capacitor (C3). An Ultrafast MURS160T3 was chosen for the freewheeling diode to minimize the amplitude of the MOSFET turn-on spike. The remaining components are involved in sensing the normal-load output current and the no-load output voltage and conveying that information back to the FEEDBACK (FB) pin of the LNK306DN. 4.4 Output Feedback The LinkSwitch-TN uses On/Off control to regulate the output of the supply. During each enabled switching cycle the drain current ramps to a fixed internal current limit level. When current into the FEEDBACK (FB) pin exceeds 49 A the next switching is disabled. By adjusting the number of enabled to disabled cycles the amount of energy delivered to the output can be varied to maintain regulation. The 49 A threshold is specified at a FB pin voltage of 1.65 V allowing this pin to be used as a voltage reference. In this design both current and voltage feedback is used. Current feedback limits the LED current during normal operation while voltage feedback limits the output voltage should the LED load be disconnected, for example during production testing. During the off time of U1, the voltage that appears across C2 is equal to the output voltage less a diode drop. In this design two 250 V rated diodes, D1 and D2, were used for space reasons, however a single 600 V diode could be used (in this case the voltage across C2 would be equal to the output voltage).
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 7 of 24
RDR-131 LED Driver - LNK306DN
7-Mar-07
This voltage is divided by R7 and R1 so the voltage at the FB pin is 1.65 V when the output voltage reaches ~12 V. Due to the interaction with the current sense circuit and the small output capacitor value the actual peak no-load voltage is limited to ~18 V. Current feedback is provided by sensing the voltage drop across R8 and R10, which is filtered by R4 and C6. Once the voltage drop exceeds the VBE of Q1, both Q1 and Q2 turn on, feeding additional current into the FB pin of U1 from C2. By adjusting the ratio of enabled to disabled cycles the average output current is controlled. As the VBE of Q1 varies with temperature the circuit exhibits a negative output current temperature coefficient. Resistor R11 provides a minimum load to ensure correct operation at zero load. This relatively complicated current sense can be simplified by using the FB pin directly to sense the voltage drop across the sense resistors. However as the FB pin has a voltage of 1.65 V this resulted in unacceptable dissipation (0.3 A x 1.65 V = 0.5 W) inside the GU10 enclosure. However in less thermally challenging designs this approach may be used.
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 8 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
Filter Board
Converter Board (Bottom and Top Side)
Figure 4 - Printed Circuit Board Layouts.
Page 9 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
5 Bill of Materials
The BOM for each board is presented separately. 5.1
Item 1 2 3 4 5 6
Filter Board Bill of Materials
Qty 1 2 3 0.08 Ft. 1 1 0.17 Ft. 0.07 Ft. 0.03 Ft. 0.07 Ft. 0.15 Ft. 0.06 Ft. Ref Des BR1 C1 C2 Value MB6S 4.7 F Description Mfg Part Number Mfg Comment
600 V, 0.5 A, Bridge MB6S Vishay Rectifier, SMD, TO-269AA 4.7 F, 380 V, Electrolytic, XX380VB4R7M8 Nippon X11LL Chemi-Con (8 x 11.5) N/A 298 SBC1-102-211 CRF253-4 10R N/A Alpha Tokin Vitrohm Solder wire in J1 Location (apply teflon tubing (SW1) over wire) Solder wire in J2 location (apply teflon tubing (SW2) over wire) Solder wire in J3 location (teflon tubing not required) Place over JP1 Place over W1 Place over W2
PCB PCB Terminal Hole, 22 J1 J2 J3 Terminal AWG 22 AWG Wire Jumper, NonJP1 insulated, 22 AWG, 0.6 in 1000 H, 0.21 A, 5.5 x L1 1000 H 10.5 mm 10 , 2.5 W, RF1 10 Fusible/Flame Proof Wire Wound W1 Wire Jumper, Noninsulated, 22 AWG Wire Jumper, Noninsulated, 22 AWG Wire Jumper, Noninsulated, 22 AWG
7
298
Alpha
8
W2
298
Alpha
9 10 11 12
W3 SJP1 SW1 SW2
298
Alpha Alpha Alpha Alpha
Teflon Tubing for 22 AWG TFT-200-22 wire Teflon Tubing for 22 AWG TFT-200-22 wire Teflon Tubing for 22 AWG TFT-200-22 wire
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 10 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
5.2
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Converter Board Bill of Materials
Qty Ref Des 3 1 2 1 2 1 1 1 2 3 1 1 1 1 1 Value Description 100 nF 25 V, Ceramic, X7R, 0603 2.2 uF, 25 V, Ceramic, X7R, 1206 Mfg Part Number ECJ-1VB1E104K ECJ-3YB1E225K Mfg Panasonic Panasonic Diode Inc. On Semi N/A ICE Components Diodes Inc Diodes Inc Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Power Integrations Alpha Solder wire in J2 Location (teflon tubing is not required) Comment
C1 C2 C6 100 nF C3 D1 D2 D3 J1 J2 L2 Q1 Q2 R1 R9 2.2 F BAV21WS-7-F MURS160T3 PCB Terminal 22 AWG 1000 H MMST3904 MMST3906 4.7 k
250 V, 0.2 A, Fast BAV21WS-7-F Switching, 50 ns, SOD-323 600 V, 1 A, Ultrafast Recovery, 35 ns, SMB Case PCB Terminal Hole, 22 AWG 1000 H, 0.3 A NPN, Small Signal BJT, 40 V, 0.2 A, SOT-323 PNP, Small Signal BJT, 40 V, 0.2 A, SOT-323 4.7 k, 5%, 1/10 W, Metal Film, 0603 10 k, 5%, 1/10 W, Metal Film, 0603 30 k, 5%, 1/10 W, Metal Film, 0603 2 , 5%, 1/4 W, Metal Film, 1206 12 , 5%, 1/10 W, Metal Film, 0603 1 k, 5%, 1/4 W, Metal Film, 1206 LinkSwitch-TN, LNK306D, SO-8 Wire jumper, non insulated, 22 AWG MURS160T3G N/A L03316-102-RM MMST3904-7-F MMST3906-7 ERJ-3GEYJ472V ERJ-3GEYJ103V ERJ-3GEYJ303V ERJ-8GEYJ2R0V ERJ-3GEYJ120V ERJ-8GEYJ102V LNK306D
R3 R4 R6 10 k R7 R8 R10 R11 U1 30 k 2 12 1 k LNK306D
16
0.17 W2 Ft.
298
17 18
1 1
J3 J4
CON1 CON1
Test Point, RED, Miniature 5000 THRU-HOLE MOUNT Test Point, BLK, Miniature 5001 THRU-HOLE MOUNT
Keystone Keystone
Page 11 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
6
PI Xls Design Spreadsheet
INPUT INFO OUTPUT UNIT LinkSwitch-TN_Rev_2-2.xls: LinkSwitch-TN Design Spreadsheet
ACDC_LinkSwitchTN_030906; Rev.2.2; Copyright Power Integrations 2006 INPUT VARIABLES VACMIN VACMAX FL VO IO EFFICIENCY (User Estimate) EFFICIENCY (Calculated Estimate) CIN Input Stage Resistance Ambient Temperature Switching Topology Input Rectification Type
85 265 50 12.00 0.330 0.72 0.78 9.40
Volts Volts Hertz Volts Amps
Customer Minimum AC Input Voltage Maximum AC Input Voltage Line Frequency Output Voltage Output Current Overall Efficiency Estimate (Adjust to match Calculated, or enter Measured Efficiency) Calculated % Efficiency Estimate
F
9.40 uF Input Filter Capacitor 0.00 ohms Input Stage Resistance, Fuse & Filtering 50 deg Operating Ambient Temperature (deg Celsius) C Buck Type of Switching topology F Choose H for Half Wave Rectifier and F for Full Wave Rectification
DC INPUT VARIABLES VMIN VMAX LinkSwitch-TN LinkSwitch-TN ILIMIT ILIMIT_MIN ILIMIT_MAX FSMIN VDS PLOSS_LNK DIODE VD VRR IF TRR Diode Recommendation OUTPUT INDUCTOR L_TYP
79.1 Volts Minimum DC Bus Voltage 374.8 Volts Maximum DC Bus Voltage
Auto
LNK306 0.482 Amps 0.450 Amps 0.515 Amps 62000 Hertz 6.2 Volts 0.51 Watts
Selected LinkSwitch-TN Typical Current Limit Minimum Current Limit Maximum Current Limit Minimum Switching Frequency Maximum On-State Drain To Source Voltage drop Estimated LinkSwitch-TN losses
0.70 Volts 600 Volts 1 Amps 35 ns BYV26C
Freewheeling Diode Forward Voltage Drop Recommended PIV rating of Freewheeling Diode Recommended Diode Continuous Current Rating Recommended Reverse Recovery Time Suggested Freewheeling Diode
941.6
L L_R OPERATING MODE KL_TOL K_LOSS ILRMS
1000 2.0 CCM 1.15 0.813 0.33
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
uH Required value of Inductance to deliver Output Power (Includes device and inductor tolerances) Choose next higher standard available value uH Output Inductor, Recommended Standard Value Ohm DC Resistance of Inductor s Continuous Conduction Mode (at VMIN) Inductor tolerance Factor. Accounts for basic (10% 20%) Manufacturing Tolerances 1.1 < KL_TOL < 1.2 See AN-37 for detailed explanation Loss factor. Accounts for "off-state" power loss to be supplied by inductor Calculated efficiency < K_LOSS < 1. See AN-37 for detailed explanation Amps Estimated RMS inductor current (at VMAX)
Page 12 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
OUTPUT CAPACITOR DELTA_V MAX_ESR I RIPPLE FEEDBACK COMPONENTS RBIAS RFB CFB C_SOFT_START
0.12 Volts Target Output Voltage Ripple 467 m- Maximum Capacitor ESR (milli-Ohms) Ohm s 0.26 Amps Output Capacitor Ripple current
kOhm s 11.86 kOhm s 10 uF 39092 uF
2.00
Bias Resistor. Use closest standard 1% value Feedback Resistor. Use closest standard 1% value Feedback Capacitor If the output Voltage is greater than 12 V, or total output and system capacitance is greater than 100 uF, a soft start capacitor between 1uF and 10 uF is recommended. See AN-37 for details
Note: The feedback components in the spreadsheet were not used on the power supply because a higher impedance was required by the CC feedback circuit.
Page 13 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
7 Performance
7.1 Efficiency Efficiency measured at different line voltages are collected in the table below.
VAC IN Efficiency 85 0.642 115 0.639 220 0.588 265 0.562 Table 1: Efficiency data measured at different AC input line voltages.
1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 70 120 170 220 270
Efficiency
VAC
Figure 5 - Efficiency vs. Input Voltage, Room Temperature.
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 14 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
7.2
Output Current Regulation Vs. Line Voltage
400 380 360
Output Current (mA
340 320 300 280 260 240 220 200 50 100 150 200 250 300
Input Voltage (VAC)
Figure 6 - Output Current vs. Input Voltage (stabilized, room temperature operation*).
7.3
Output VI Characteristic
16 14 12 85 VAC 265VAC
Output Voltage
10 8 6 4 2 0 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45
Output Current (mA)
Figure 7 - Output Current vs. Output Voltage.
Note: When driving a LED load operation at <6V would not occur, therefore current walkout behavior is acceptable. Page 15 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
8 Waveforms
8.1 Drain Voltage and Current, Normal Operation
Figure 7 - 85 VAC, Full Load. Upper: VDRAIN, 50 V / div. Lower: IDRAIN 0.20 A / div, 5 s / div.
Figure 8 - 265 VAC, Full Load Upper: VDRAIN, 100 V / div. Lower: IDRAIN 0.20 A / div, 5 s / div.
8.2
Output Current and Voltage
Figure 9 - 85 VAC, Full Load. Upper: VOUT, 5 V / div. Lower: IOUT, 100 mA, 20 s / div.
Figure 10 - 265 VAC, Full Load. Upper: VOUT, 5 V / div. Lower: IOUT, 100 mA, 20 s / div.
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 16 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
8.3
Drain Current and Bulk Capacitor Voltage
Figure 11 - 85 VAC, Full Load. Upper: VBULK, 100 V / div. Lower: IDRAIN, 200 mA, 5 ms / div.
Figure 12 - 265 VAC, Full Load. Upper: VBULK, 100 V / div. Lower: IDRAIN, 200 mA, 5 ms / div.
8.4
Startup Drain Current and Bulk Capacitor Voltage
Figure 13 - 85 VAC, Full Load. Upper: VBULK, 50 V / div. Lower: IDRAIN, 200 mA, 5 ms / div.
Figure 14 - 265 VAC, Full Load. Upper: VBULK, 200 V / div. Lower: IDRAIN, 200 mA, 5 ms / div.
Page 17 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
8.5
Startup Output Voltage and Current
Figure 15 - 85 VAC Full Load. Upper: Vout, 5 V / div. Lower: Iout, 200 mA / div, 5 ms / div.
Figure 16 - 265 VAC Full Load. Upper: Vout, 5 V / div. Lower: Iout, 200 mA / div, 5 ms / div.
8.6
Fault Conditions
Figure 17 - Drain Current with Output Shorted. 500 mA/div, 2 ms / div. Vin = 265 VAC Note: Peak drain current is 1.95 Amps.
Figure 18 - Output Voltage with No Load. 5 V/div, 1 ms / div. Vin = 265 VAC Note: Peak voltage is 18 Volts.
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 18 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
9 Thermal Measurements
The power supply assembly was installed into the lamp socket base and the temperature of the LNK306DN SOURCE pin was measured, while the room ambient temperature was 25 C. The power supply was driving the three load LEDs (delivering 3 watts). Vin (VAC) 85 115 230 265 Source Pin Temperature (C) 81 82 97 103
These results indicate that additional heatsinking may be required for example by arranging the LED heatsink to contact the top of the SO-8C package of U1.
Page 19 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
10 Conducted EMI
The measurements were taken with the power supply driving the 3 LEDs. The worstcase input voltage was at 230 VAC, where the margin to the test limits was about 7 dBV.
dBV
80
70 1 QP CLRWR 2 AV CLRWR
1 MHz LIMIT CHECK MARG LINE EN55022A MARG LINE EN55022Q MARG
10 MHz
SGL
EN55022Q
60
EN55022A
50
1
TDF
40
30
20
10
0
-10
-20
150 kHz
30 MHz
Figure 19 - Conducted EMI at 230 VAC.
,
dBV 100 90 1 QP CLRWR 2 AV CLRWR 80 70 EN55022Q 60 EN55022A 50 40 1 30 20 10 0 -10 -20 1 5 0 k Hz 30 MHz TDF 1 MHz LIMIT CHECK MARG LINE EN55022A MARG LINE EN55022Q MARG 10 MHz
SGL
Figure 20 - Conducted EMI at 115 VAC.
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 20 of 24
7-Mar-07 10.1 Competitive Product EMI
Power Integrations 01.Feb 07 08:52 Att 10 dB AUTO
dBV 100
RDR-131 LED Driver - LNK306DN
RBW 9 kHz MT 100 ms PREAMP OFF
Marker 1 [T1 ] 89.31 dBV 182.849162999 kHz 10 MHz
1
90 1 QP CLRWR 2 AV CLRWR
1 MHz LIMIT CHECK FAIL LINE EN55022A FAIL LINE EN55022Q FAIL
SGL
80
70
EN55022Q
60
TDF
EN55022A
50
40
30
20
10
0
-10 -20
150 kHz
30 MHz
Figure 21 - Conducted EMI at 115VAC of competitive product.
This result was taken to demonstrate the poor EMI performance of similarly rated LED drivers on the market.
Page 21 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
11 Revision History
Date
02/16/2007 03/7/2007
Author
JAJ
Revision
1.0 1.1
Description & changes
Initial publication Updated pictures
Reviewed
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 22 of 24
7-Mar-07
RDR-131 LED Driver - LNK306DN
Notes
Page 23 of 24
Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
RDR-131 LED Driver - LNK306DN
7-Mar-07
For the latest updates, visit our website: www.powerint.com
Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability. Power Integrations does not assume any liability arising from the use of any device or circuit described herein. POWER INTEGRATIONS MAKES NO WARRANTY HEREIN AND SPECIFICALLY DISCLAIMS ALL WARRANTIES INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. PATENT INFORMATION The products and applications illustrated herein (including transformer construction and circuits external to the products) may be covered by one or more U.S. and foreign patents, or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A complete list of Power Integrations' patents may be found at www.powerint.com. Power Integrations grants its customers a license under certain patent rights as set forth at http://www.powerint.com/ip.htm. The PI Logo, TOPSwitch, TinySwitch, LinkSwitch, DPA-Switch, PeakSwitch, EcoSmart, Clampless, E-Shield, Filterfuse, StackFET, PI Expert and PI FACTS are trademarks of Power Integrations, Inc. Other trademarks are property of their respective companies. (c)Copyright 2007 Power Integrations, Inc.
Power Integrations Worldwide Sales Support Locations
WORLD HEADQUARTERS 5245 Hellyer Avenue San Jose, CA 95138, USA. Main: +1-408-414-9200 Customer Service: Phone: +1-408-414-9665 Fax: +1-408-414-9765 e-mail: usasales@powerint.com GERMANY Rueckertstrasse 3 D-80336, Munich Germany Phone: +49-89-5527-3910 Fax: +49-89-5527-3920 e-mail: eurosales@powerint.com JAPAN 1st Bldg Shin-Yokohama |2-12-20 Kohoku-ku, Yokohama-shi, Kanagawa ken, Japan 222-0033 Phone: +81-45-471-1021 Fax: +81-45-471-3717 e-mail: japansales@powerint.com KOREA RM 602, 6FL Korea City Air Terminal B/D, 159-6 Samsung-Dong, Kangnam-Gu, Seoul, 135-728, Korea Phone: +82-2-2016-6610 Fax: +82-2-2016-6630 e-mail: koreasales@powerint.com SINGAPORE 51 Newton Road, #15-08/10 Goldhill Plaza, Singapore, 308900 Phone: +65-6358-2160 Fax: +65-6358-2015 e-mail: singaporesales@powerint.com TAIWAN 5F, No. 318, Nei Hu Rd., Sec. 1 Nei Hu Dist. Taipei, Taiwan 114, R.O.C. Phone: +886-2-2659-4570 Fax: +886-2-2659-4550 e-mail: taiwansales@powerint.com
CHINA (SHANGHAI) Rm 807-808A, Pacheer Commercial Centre, 555 Nanjing Rd. West Shanghai, P.R.C. 200041 Phone: +86-21-6215-5548 Fax: +86-21-6215-2468 e-mail: chinasales@powerint.com
INDIA #1, 14th Main Road Vasanthanagar Bangalore-560052 India Phone: +91-80-41138020 Fax: +91-80-41138023 e-mail: indiasales@powerint.com
UNITED KINGDOM 1st Floor, St. James's House East Street, Farnham Surrey, GU9 7TJ United Kingdom Phone: +44 (0) 1252-730-140 Fax: +44 (0) 1252-727-689 e-mail: eurosales@powerint.com
CHINA (SHENZHEN) Room 2206-2207, Block A, Elec. Sci. Tech. Bldg. 2070 Shennan Zhong Rd. Shenzhen, Guangdong, China, 518031 Phone: +86-755-8379-3243 Fax: +86-755-8379-5828 e-mail: chinasales@powerint.com
ITALY Via De Amicis 2 20091 Bresso MI - Italy Phone: +39-028-928-6000 Fax: +39-028-928-6009 e-mail: eurosales@powerint.com
APPLICATIONS HOTLINE World Wide +1-408-414-9660 APPLICATIONS FAX World Wide +1-408-414-9760
Power Integrations, Inc. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com
Page 24 of 24

▲Up To Search▲

Price & Availability of RDR-131

	To Download RDR-131 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .