|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
ADVANCED PRODUCT INFORMATION - Rev 0.0 HELP PCS/CDMA 3.4V/28dBm Linear Power Amplifier Module TM AWT6138 FEATURES High InGaP HBT Technology Efficiency: 38% at +28 dBm 20% at +16 dBm 1.5% at 0 dBm Low Quiescent Current: 20 mA Low Leakage Current in Shutdown Mode: <1 mA VREF = +2.85 V (+2.7 V min over temp) Low Profile Surface Mount Package: 1.56mm Max CDMA 1XRTT and 1xEV-DO Compliant APPLICATIONS PCS CDMA Wireless Handsets Dual Band CDMA Wireless Handsets M7 Package 10 Pin 4mm x 4mm Surface Mount Module handset. The device has mode-switching to take advantage of its high efficiency operation over a wide range of output powers. Higher low power efficiency is achieved without an external DAC or DC-DC converter. The integrated power amplifier module employs a proprietary bias control and temperature compensation circuit that assures stable operation, even at extreme temperature conditions. The self contained 4mm x 4mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50[ohm] system making it easy to incorporate the device into BOTH new and existing designs. GND at slug (pad) PRODUCT DESCRIPTION The AWT6138 PCS CDMA Power Amplifier is a high performance CDMA2000/ 1XRTT amplifier designed specifically for PCS wireless applications. This rugged, easy to use InGaP HBT design delivers state of the art efficiency and temperature stability with very low DC power consumption. The AWT6138 PA module has the lowest CDG currents available to handset manufacturers today. A combination of low idle current and mode switching enables the AWT6138 to deliver unparalleled CDMA average power efficiencies. This bias feature allows the AWT6138 to significantly increase the battery usage time of a mobile VCC RFIN GND 1 2 3 Bias Control 10 VCC 9 8 7 6 GND RFOUT GND GND VMODE 4 VREF 5 Figure 1: Block Diagram 09/2003 AWT6138 GND VCC RFIN GND VMODE VREF 1 2 3 4 5 GND 10 VCC 9 8 7 6 GND RFOUT GND GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description PIN 1 2 3 4 5 6 7 8 9 10 NAME V CC RFIN GND VMODE VREF GND GND RFOUT GND V CC DESCRIPTION Supply Voltage RF Input Ground Mode Control Voltage Reference Voltage Ground Ground RF Output Ground Supply Voltage 2 ADVANCED PRODUCT INFORMATION - Rev 0.0 09/2003 AWT6138 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER Supply Voltage (VCC) Mode Control Voltage (VMODE) Reference Voltage (VREF) RF Input Power (PIN) Storage Temperature (TSTG) MIN 0 0 0 -40 MAX +5 +3.5 +3.5 +10 +150 UNIT V V V dB m C Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PAR AME T E R Operating Frequency (f) Supply Voltage (VCC) Reference Voltage (VREF) Mode Control Voltage (VMODE) RF Output Power (POUT) Case Temperature (TC) MIN 1850 +3.2 +2.7 0 +2.5 0 +27.5(1) -30 T YP +3.4 +2.85 +2.8 +28.0 M AX 1910 +4.2 +2.95 +0.5 +3.1 +0.5 +85 U N IT MHz V V V dBm C PA "on" PA "shut down" Low Bias Mode High Bias Mode C OMME N T S The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at TC = +85 C and VCC = +3.2 V, POUT is derated by 0.5 dB. ADVANCED PRODUCT INFORMATION - Rev 0.0 09/2003 3 AWT6138 Table 4: Electrical Specifications (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, 50 W system) PARAMETER Gain Adjacent Channel Power (1) at 1.25 MHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz Adjacent Channel Power (1) at 2.25 MHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz Power-Added Efficiency Quiescent Current (Icq) Reference Current Mode Control Current Leakage Current Noise in Receive Band Harmonics 2fo 3fo, 4fo Input Impedance (1) MIN - TYP 26 15 MAX - UNIT dB COMMENTS POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V - -50 -52 - dB POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V - -60 -60 38 20 1.5 20 6 1.3 <1 -137 -40 -50 - 9 2.5 5 -30 -30 2:1 dB POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V POUT = 0 dBm, VMODE = +2.85 V VMODE = +2.85 V through VREF pin through VMODE pin, VMODE = +2.85 V VCC = +4.2 V, VREF = 0 V VMODE = 0 V % mA mA mA A dBm/Hz 1930 MHz to 1990 MHz dB c VSWR POUT < +28 dBm In-band load VSWR < 8:1 Out-of-band load VSWR < 8:1 Applies over all voltage and temperature operating ranges VCC = +5.0 V, PIN = +5 dBm Applies over full operating temperature range Spurious Output Level (all spurious outputs) - - -65 dB c Load mismatch stress with no permanent degradation or failure 8:1 - - VSWR Notes: 1. PAE and ACP limit applies at 1880 MHz 4 ADVANCED PRODUCT INFORMATION - Rev 0.0 09/2003 AWT6138 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic levels (see Operating Ranges table) to the VMODE Voltage. The Bias Control table lists the recommended modes of operation for various applications. Table 5: Bias Control AP P L IC AT ION CDMA - low power CDMA - hi gh power Shutdown P OU T LEVELS <+16dBm >+16 dBm B IAS MOD E Low Hi gh Shutdown V R EF V MOD E +2.85 V +2.85 V +2.85 V 0V 0V 0V VCC1 VCC2 C1 0.01F RF IN VMODE VREF 1 2 3 4 5 VCC RFIN GND VMODE VREF VCC GND RFOUT GND GND GND at slug 10 9 8 7 6 C3 0.01F C4 2.2F ceramic RF OUT C2 0.01F Figure 3: Application Circuit Schematic ADVANCED PRODUCT INFORMATION - Rev 0.0 09/2003 5 AWT6138 PACKAGE OUTLINE Figure 4: M7 Package Outline - 10 Pin 4mm x 4mm Surface Mount Module Figure 5: Branding Specification 6 ADVANCED PRODUCT INFORMATION - Rev 0.0 09/2003 AWT6138 COMPONENT PACKAGING Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions PACKAGE TYPE 4mm X 4mm TAPE WIDTH 12mm POCKET PITCH 8mm REEL CAPACITY 2500 MAX REEL DIA 13" ADVANCED PRODUCT INFORMATION - Rev 0.0 09/2003 7 AWT6138 ORDERING INFORMATION OR D E R N U MB E R T E MP E R AT U R E R AN GE -30 oC to +110 oC PAC K AGE D E S C R IP T ION 10 Pin 4mm x 4mm Surface Mount Module C OMP ON E N T PAC K AGIN G AWT6138M7P8 Tape and Reel, 2500 pieces per Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a products formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. WARNING 8 ADVANCED PRODUCT INFORMATION - Rev 0.0 09/2003 |
Price & Availability of AWT6138M7P8 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |