View MN101D08E_991713.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MN101D08E
Type ROM (x8-bit) x RAM (x 8-bit) x Package Minimum Instruction Execution Time Interrupts
With main clock operated When sub-clock operated MN101D08E 80 K 2K LQFP080-P-1414A *Lead-free
VTR Servo
0.1397 s (at 4.0 V to 5.5 V, 14.32 MHz) 71.5 s (at 2.7 V to 5.5 V fixed to 14.32 MHz internal frequency division) 61 s (at 2.5 V to 5.5 V, 32.768 kHz)
* RESET * Runaway * External 0, 1, 2, 3, 4 * Timer 0 * Timer 1 * Timer 2 * Timer 3 * Timer 6 * Capstan FG * Control * HSW * Cylinder FG * Servo VSYNC * Synchronous output * OSD * XDS * Serial 1 * Serial 2 * PWM 4 * OSDVSYNC Timer counter 0: 8-bit x 1 (timer function) Clock source ********************* 1/4, 1/16 of system clock frequency Interrupt source **************** overflow of timer counter 0 Timer counter 1: 8-bit x 1 (timer function, linear timer counter function) Clock source ********************* 1/4 of system clock frequency; CTL signal Interrupt source **************** overflow of timer counter 1 Timer counter 2: 16-bit x 1 (timer function, input capture (DCTL specified edge), duty judgment of DCTL signal) Clock source ********************* 1/4, 1/16, 1/24 of system clock frequency Interrupt source **************** overflow of timer counter 2; input of DCTL specified edge; underflow of timer 2 shift register 4-bit counter; coincidence of timer 2 shift register with timer 2 shift register compare register Timer counter 3: 16-bit x 1 (timer function, detection of serial indexing, generation of remote control output carrier frequency) Clock source ********************* 1/4, 1/16 of system clock frequency Interrupt source **************** overflow of timer counter 3 Timer counter 5: 19-bit x 1 (watchdog, stable oscillation waiting function) Clock source ********************* system clock Watchdog interrupt source ** 1/216, 1/219 of timer counter 5 frequency Clear by stable oscillation ** after 256 counts by timer counter 5 (2 18 counts of OSC oscillation clock) Timer counter 6: 16-bit x 1 (clock function [max. 2 s]) Clock source ********************* 1/512 of OSC oscillation clock frequency; XI oscillation clock; 1/8, 1/128 of system clock frequency Interrupt source **************** 1/213, 1/214, 1/215 overflow of timer counter 6
Timer Counter
Serial Interface
Serial 1: 8-bit x 1 (synchronous type/remote control transmission/simple remote control receive) (transfer direction of MSB/LSB selectable, start condition function) Clock source ********************* 1/8, 1/16, 1/32, 1/64, 1/128, 1/256 of system clock frequency; SBT1 pin input Serial 2: 8-bit x 1 (I2 C) (master transmission/reception, slave transmission/reception) Clock source ********************* 1/144 to 1/252 of system clock; SCK pin input
1
MAD00032CEM
MN101D08E
OSD
OSD mode:Accommodation with menu or super impose display Applicable broadcasting system : NTSC, PAL, PAL-M, PAL-N Screen configuration : 24 characters x 2n rows (n = 1 to 6) Character type : max. 128 character types (variable) Character size : 12 x 18 dots (Vertical direction: 1 dot for 2H at x 1 setting.) Enlarged characters : each x 2 settings in horizontal and vertical Character interpolation : none Line background color : 8-hue settable (settable in the row unit at menu display) Line background intensity : 8 gradations settable in the row unit Screen background color : 8-hue settable (at output of composite video signal) Character color : white Character intensity : 8 gradations settable in the row unit Frame function : 1-dot frame in 4 directions Frame intensity : 4 gradations settable in the row unit Blinking : none (covered by software) Inverted character : settable in the character unit Halftone : none Common: Input : composite video signal input (output level: 1 V[p-p] / 2 V[p-p]) Clamp method : sync chip clamp, clamp level in 4 levels Output : composite video output Measure against image fluctuation : built-in AFC circuit Dot clock : 1/2 of OSC oscillation clock (automatic phase adjustment) Built-in U.S. closed caption data slicer (optional 1 line data can be extracted.) Correcting address designation: up to 3 addresses possible Correction method: correction program being saved in internal RAM
XDS ROM Correction I/O Pins A/D Inputs PWM ICR OCR Special Ports Notes I/O Input
56 1
* Common use: 56 ports 0, 1, 2, 4, 6, 7, B (by bit) * Common use: 1
8-bit x 11-ch. (without S/H) 13-bit x 2-ch. (at repetition cycle 572 s, 14.32 MHz), 8-bit x 1-ch. (at repetition cycle 35.7 s, 14.32 MHz) 18-bit x 6-ch. 16-bit x 7-ch. , 8-bit x 1-ch. 3-state output (PTO) VLP pin; synchronous output: 7; 3-state synchronous output: 4; CTL amp; built-in FG amp; output of 1/4 OSC oscillation clock (1 V[p-p]) VISS/VASS detection function
See the next page for electrical characteristics, pin assignment and support tool.
MAD00032CEM
2
Electrical Characteristics
Supply current
Limit Parameter Symbol IDD1 Operating supply current IDD2 IDD3 32 kHz oscillation operation without load Supply current at STOP IDSP IDHT0 Supply current at HALT IDHT1 32 kHz oscillation operation without load Stop of oscillation without load, VDD = 5 V 14.32 MHz oscillation without load, VDD = 5 V Stop of 14.32 MHz oscillation, VDD = 2.7 V 5 20 5 20 15 A mA A Condition min 14.32 MHz operation without load, VDD = 5 V 1/1024 of 14.32 MHz operation without load, VDD = 2.7 V Stop of 14.32 MHz oscillation, VDD = 2.7 V 50 100 typ 50 2 max 100 5 mA mA A Unit
(Ta = 25C 2C , VSS = 0 V)
A/D Converter Performance
Limit Parameter Conversion relative error A/D Conversion Time Analog Input Voltage Symbol NLAD tAD fosc = 14.32 MHz 8 5 Condition min typ max 3 LSB s V Unit
(Ta = 25C 2C , VDD = 5.0 V, VSS = 0 V)
3
MAD00032CEM
MN101D08E
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
(PC0)AD8 (P87)AD7 (P86)AD6 (P85)AD5 (P84)AD4 (P83)AD3 (P82)AD2 (P81)AD1 (P80)AD0
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
41
C0 RCTLN RCTLP AVDD CTLA AVSS VRI VR0 AFG FGF YPG(PB7) YFG(PFG) FSCLPF(PB0) FSCI(PB1) AFCLPF(PB2) AFCC(PB3) VDD2 CVIN2(PB4)
Pin Assignment
AD10(PC2) AD9(PC1)
40 39 38 37 36 35 34 33 32
CVIN (PB5)
P77 P76 P75 P74 P73 P72 P71 P70
(P67)ROTA (P66)HAMP (P65)DENV
MN101D08E
31 30 29 28 27 26 25 24 23 22 21
VSS2 CVOUT (PB6) SXI X0 (P23) XI (P24) VSS OSCI OSC0 VDD PWM4(P25) PWM0 PWM1 SBUFD1(P11) SBUFD2(P12) SBUFD3(P13) SBUFD4(TC60/P14) SBUFD5(P15) SBUFD6(P16) SBUFD7(OSCDIV/P17)
10
11
12
13
14
15
16
17
18
19
(P64)IRQ0
(P46)HBUFD6
(P44)HBUFD4
(P42)HBUFD2
(P40)HBUFD0
(P05)NSB01
(P07)NSBT1
(P26)SCK
HSW
VLP
P02
P01
P00
(P06)NSBI1
LQFP080-P-1414A
*Lead-free
Support Tool
In-circuit Emulator Flash Memory Built-in Type
PX-ICE101C / D + PX-PRB101D08-LQFP080-P-1414A Type ROM (x 8-bit) RAM (x 8-bit) Minimum instruction execution time MN101DF08G [ES (Engineering Sample) available] 128 K 4K 0.1397 s (at 4.0 V to 5.5 V, 14.32 MHz) 71.5 s (at 2.7 V to 5.5 V, fixed to 14.32 MHz internal division) Package LQFP080-P-1414A *Lead-free
(P04)NRST
(P63)IRQ1
(P62)IRQ2
(P61)IRQ3
(P60)IRQ4
(P27)SDA
20
1
2
3
4
5
6
7
8
9
MAD00032CEM
4
Request for your special attention and precautions in using the technical information and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd.
2002 JUL

▲Up To Search▲

Price & Availability of MN101D08E

	To Download MN101D08E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .