|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
19-1372; Rev 1; 6/98 MAX881R Evaluation Kit General Description The MAX881R IC is an inverting, charge-pump DC-DC converter with a low-noise, regulated output. Low output ripple voltage makes this device ideal for biasing the GaAsFETs commonly found in cellular telephone transmitters. The MAX881R evaluation kit (EV kit) is a fully assembled and tested surface-mount board. Provisions are made for mounting a second voltage-divider resistor, which is required for setting output voltages other than -2V. A special scope-probe socket is also mounted on the board, so output noise can be observed on an oscilloscope. o 1mVp-p Output Voltage Ripple o 2.5V to 5.5V Input Range o Uses One 4.7F and Three 1F Ceramic Capacitors o -2V Regulated Output (or Adjustable) o 4mA Output Current o Power OK (POK) Output o Fully Assembled and Tested Surface-Mount Board Features Evaluates: MAX881R Component List DESIGNATION QTY C1, C2, C3 C4 J1 JU1 R1 R2 R3, R4 U1 None None 3 1 1 1 0 1 2 1 1 1 DESCRIPTION 1F, 16V, low-ESR ceramic capacitors Taiyo Yuden EMK316BJ105KL 4.7F, 10V, low-ESR ceramic capacitor Taiyo Yuden LMK316BJ475ML Scope-probe connector Berg Electronics 33JR135-1 2-pin jumper Not installed 100k, 1% resistor 1M resistors MAX881RREUB Shunt Printed circuit board PART MAX881REVKIT Ordering Information TEMP. RANGE -40C to +85C IC PACKAGE 10 MAX Quick Start The MAX881R EV kit is fully assembled and tested. Follow the steps below to verify board operation. Do not turn on the power supply until all connections are completed. 1) Connect a 2.5V to 5.5V supply to the pad labeled VIN. Connect the ground lead to the pad labeled GND. 2) Connect a voltmeter and the load to the VOUT pad. 3) Make sure there is no shunt across JU1. 4) Turn on the power and verify that the output is -2V. You can insert a scope probe into J1 to observe the output noise. Be sure the scope ground makes contact with the outside of the connector. Component Suppliers SUPPLIER Berg Electronics Sprague Taiyo Yuden PHONE (317) 738-2800 (603) 224-1961 (408) 573-4150 FAX (317) 738-2858 (603) 224-1430 (408) 573-4159 ________________________________________________________________ Maxim Integrated Products 1 For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468. MAX881R Evaluation Kit Evaluates: MAX881R Detailed Description Jumper Selection The 2-pin header, JU1, controls pin 5 (SHDN) on the IC. Table 1 outlines the shunt positions for JU1. The POK pad allows easy connection to an external system. This output pulls low when the bias voltage has reached 92.5% of its set value. Capacitor Selection Use capacitors with a low effective series resistance (ESR), such as ceramic or surface-mount chip tantalum types. Output ripple with the supplied components is typically 1mVp-p. For lower output ripple, replace C4 with a 10F ceramic capacitor such as the Taiyo Yuden JMK316BJ106ML or a 10F tantalum such as the Sprague 595D106X0010A2. Output Voltage Adjustment For output voltages other than -2V, install R1 to complete the R1/R2 output voltage divider. R2 is a 100k, 1% resistor. To maintain accuracy, use a 1% resistor for R1. Use the following equations to calculate R1: R1 = -R2 (2 x VOUT + 1) R1 = -100k (2 x VOUT + 1) Table 1. JU1 Shunt Position SHUNT POSITION Open Closed MAX881R FUNCTION Device enabled, or apply signal to the SHDN pad Device disabled 1 C1 1F 2 C3 1F 3 R3 1M POK 4 R4 1M 5 C1+ IN 10 VIN 2.5V to 5.5V C1- U1 MAX881R N.C. 9 C2 1F NEGOUT GND 8 GND J1 VOUT R1 OPEN C4 4.7F POK OUT 7 SHDN SHDN FB 6 VOUT R2 100k 1% GND JU1 Figure 1. MAX881R EV Kit Schematic 2 _______________________________________________________________________________________ MAX881R Evaluation Kit Evaluates: MAX881R 1.0" Figure 2. MAX881R EV Kit Component Placement Guide-- Component Side 1.0" Figure 3. MAX881R EV Kit PC Board Layout--Component Side 1.0" Figure 4. MAX881R EV Kit PC Board Layout--Solder Side _______________________________________________________________________________________ 3 MAX881R Evaluation Kit Evaluates: MAX881R NOTES Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 4 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 1998 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. |
Price & Availability of MAX881REVKIT |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |