 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DSP56852/D Rev. 2.0 4/2002 DSP56852 Preliminary Technical Data DSP56852 16-bit Digital Signal Processor * 120 MIPS at 120MHz * 6K x 16-bit Program SRAM * 4K x 16-bit Data SRAM * 1K x 16-bit Boot ROM * 21 External Memory Address lines, 16 data lines and four chip selects * One (1) Serial Port Interface (SPI) or one (1) Improved Synchronous Serial Interface (ISSI) * One (1) Serial Communication Interface (SCI) VDDIO 6 6 VDD 3 VSSIO 6 VSS VDDA 3 VSSA * Interrupt Controller * General Purpose 16-bit Quad Timer * JTAG/Enhanced On-Chip Emulation (OnCETM) for unobtrusive, real-time debugging * Computer Operating Properly (COP)/Watchdog Timer * 81-pin MAPBGA package * Up to 11 GPIO JTAG/ Enhanced OnCE Program Controller and Hardware Looping Unit Address Generation Unit 16-Bit DSP56800E Core Data ALU 16 x 16 + 36 36-Bit MAC Three 16-bit Input Registers Four 36-bit Accumulators Bit Manipulation Unit PAB PDB CDBR CDBW Memory XDB2 R/W Control XAB1 XAB2 PAB PDB Program Memory 6144 x 16 SRAM Boot ROM 1024 x 16 ROM Data Memory 4096 x 16 SRAM System Bus Control CDBR CDBW System Address Decoder System Device IPBus Bridge (IPBB) RW Control IPAB IPWDB IPRDB Peripheral Address Decoder Decoding Peripherals A0-16 A17-18 muxed (timer pins) A19 muxed (CS3) D0-D12[12:0] D13-15 muxed (Mode A,B,C) WR Enable RD Enable CS[2:0] muxed (GPIOA) External Address Bus Switch External Data Bus Switch Bus Control External Bus Interface Unit Peripheral Device Selects Clock resets PLL SCI or GPIOE 1 Quad Timer or A17, A18 2 SSI or SPI or GPIOC COP/ Watchdog Interrupt Controller P O R System Integration Module Clock Generator O S C XTAL EXTAL 2 6 IRQA IRQB 3 CLKO RESET muxed (A20) MODE muxed (D13-15) Figure 1. DSP56852 Block Diagram (c) Motorola, Inc., 2002. All rights reserved. Part 1 Overview 1.1 DSP56852 Features 1.1.1 * * * * * * * * * * * * * * * * Digital Signal Processing Core Efficient 16-bit DSP engine with dual Harvard architecture 120 Million Instructions Per Second (MIPS) at 120MHz core frequency Single-cycle 16 x 16-bit parallel Multiplier-Accumulator (MAC) Four (4) 36-bit accumulators including extension bits 16-bit bidirectional shifter Parallel instruction set with unique DSP addressing modes Hardware DO and REP loops Three (3) internal address buses and one (1) external address bus Four (4) internal data buses and one (1) external data bus Instruction set supports both DSP and controller functions Four (4) hardware interrupt levels Five (5) software interrupt levels Controller-style addressing modes and instructions for compact code Efficient C Compiler and local variable support Software subroutine and interrupt stack with depth limited only by memory JTAG/Enhanced OnCE debug programming interface 1.1.2 * * Memory Harvard architecture permits as many as three simultaneous accesses to program and data memory On-chip memory includes: -- 6K x 16-bit Program SRAM -- 4K x 16-bit Data SRAM -- 1K x 16-bit Boot ROM * 21 External Memory Address lines, 16 data lines and four (4) programmable chip select signals 1.1.3 * * * * * * Peripheral Circuits for DSP56852 General Purpose 16-bit Quad Timer with two external pins* One (1) Serial Communication Interface (SCI)* One (1) Serial Port Interface (SPI) or one (1) Improved Synchronous Serial Interface (ISSI) module* Interrupt Controller Computer Operating Properly (COP)/Watchdog Timer JTAG/Enhanced On-Chip Emulation (EOnCE) for unobtrusive, real-time debugging 2 DSP56852 Preliminary Technical Data MOTOROLA DSP56852 Description * * 81-pin MAPBGA package Up to 11 GPIO * Each peripheral I/O can be used alternately as a General Purpose I/O if not needed 1.1.4 * * Energy Information Fabricated in high-density CMOS with 3.3V, TTL-compatible digital inputs Wait and Stop modes available 1.2 DSP56852 Description The DSP56852 is a member of the DSP56800E core-based family of Digital Signal Processors (DSPs). On a single chip it combines the processing power of a DSP and the functionality of a microcontroller with a flexible set of peripherals to create an extremely cost-effective solution. Because of its low cost, configuration flexibility, and compact program code, the DSP56852 is well-suited for many applications. The DSP56852 includes many peripherals especially useful for low-end Internet appliance applications and low-end client applications such as telephony; portable devices; Internet audio; and point-of-sale systems such as noise suppression; ID tag readers; sonic/subsonic detectors; security access devices; remote metering; and sonic alarms. The DSP56800E core is based on a Harvard-style architecture consisting of three execution units operating in parallel, allowing as many as six operations per instruction cycle. The microprocessor-style programming model and optimized instruction set allow straightforward generation of efficient, compact code for both DSP and MCU applications. The instruction set is also highly efficient for C-Compilers, enabling rapid development of optimized control applications. The DSP56852 supports program execution from either internal or external memories. Two data operands can be accessed from the on-chip Data RAM per instruction cycle. The DSP56852 also provides two external dedicated interrupt lines, and up to 11 General Purpose Input/Output (GPIO) lines, depending on peripheral configuration. The DSP56852 DSP controller includes 6K words of Program RAM, 4K words of Data RAM and 1K of Boot RAM. It also supports program execution from external memory. This DSP controller also provides a full set of standard programmable peripherals that include one improved Synchronous Serial Interface (SSI) or one Serial Peripheral Interface (SPI), one Serial Communications Interface (SCI), and one Quad Timer. The SSI, SPI, SCI I/O and three chip selects can be used as General Purpose Input/Outputs when its primary function is not required. The SSI and SPI share I/O, so, at most, one of these two peripherals can be in use at any time. 1.3 "Best in Class" Development Environment The SDK (Software Development Kit) provides fully debugged peripheral drivers, libraries and interfaces that allow a programmer to create his own unique C application code independent of component architecture. The CodeWarrior Integrated Development Environment is a sophisticated tool for code navigation, compiling, and debugging. A complete set of evaluation modules (EVMs) and development system cards support concurrent engineering. Together, the SDK, CodeWarrior, and EVMs create a complete, scalable tools solution for easy, fast and efficient development. MOTOROLA DSP56852 Preliminary Technical Data 3 1.4 Product Documentation The four documents listed in Table 1 are required for a complete description of and proper design with the DSP56852. Documentation is available from local Motorola distributors, Motorola semiconductor sales offices, Motorola Literature Distribution Centers, or online at www.motorola.com/semiconductors/. Table 1. DSP56852 Chip Documentation Topic DSP56800E Reference Manual DSP56852 User's Manual DSP56852 Technical Data Sheet DSP56852 Product Brief Description Detailed description of the DSP56800E architecture, 16-bit DSP core processor and the instruction set Detailed description of memory, peripherals, and interfaces of the DSP56852 Electrical and timing specifications, pin descriptions, and package descriptions (this document) Summary description and block diagram of the DSP56852 core, memory, peripherals and interfaces Order Number DSP56800ERM/D DSP56852UM/D DSP56852/D DSP56852PB/D 1.5 Data Sheet Conventions This data sheet uses the following conventions: OVERBAR This is used to indicate a signal that is active when pulled low. For example, the RESET pin is active when low. A high true (active high) signal is high or a low true (active low) signal is low. A high true (active high) signal is low or a low true (active low) signal is high. Signal/Symbol PIN PIN PIN PIN 1. "asserted" "deasserted" Examples: Logic State True False True False Signal State Asserted Deasserted Asserted Deasserted Voltage1 VIL/VOL VIH/VOH VIH/VOH VIL/VOL Values for VIL, VOL, VIH, and VOH are defined by individual product specifications. 4 DSP56852 Preliminary Technical Data MOTOROLA Introduction Part 2 Signal/Connection Descriptions 2.1 Introduction The input and output signals of the DSP56852 are organized into functional groups, as shown in Table 2 and as illustrated in Figure 2. In Table 3 each table row describes the package pin and the signal or signals present. Table 2. Functional Group Pin Allocations Functional Group Power (VDD, VDDIO, or VDDA) Ground (VSS, VSSIO,or VSSA) Phase Lock Loop (PLL) and Clock External Bus Signals External Chip Select* Interrupt and Program Control Synchronous Serial Interface (SSI) Port* Serial Communications Interface (SCI) Port* Serial Peripheral Interface (SPI) Port Quad Timer Module Port JTAG/Enhanced On-Chip Emulation (EOnCE) *Alternately, GPIO pins Number of Pins 101 101 22 393 34 35 6 2 06 07 6 1. VDD = VDD CORE, VSS = VSS CORE, VDDIO= VDD IO, VSSIO = VSS IO, VDDA = VDD ANA, VSSA = VSS ANA 2. CLKOUT is muxed Address pin A20. 3. Four Address pins are multiplexed with the timer, CS3 and CLKOUT pins. 4. CS3 is multiplexed with external Address Bus pin A19. 5. Mode pins are multiplexed with External Data pins D13-D15 like A17and A18. 6. Four of these pins are multiplexed with SSI. 7. Two of these pins are multiplexed with 2 bits of the External Address Bus A17and A18. MOTOROLA DSP56852 Preliminary Technical Data 5 Logic Power VDD VSS 3 3 1 1 RXD(GPIOE0) TXD(GPIOE1) SCI I/O Power VDDIO VSSIO 6 6 1 1 1 1 GPIOC0(STXD) GPIOC1(SRXD) SCLK(GPIOC2)(STCK) SS(GPIOC3)(STFS) MISO(GPIOC4)(SRCK) MOSI(GPIOC5)(SRFS) SPI SSI Analog Power1 VDDA VSSA 1 1 1 1 DSP56852 A0-16 A17(TI/O) Address Bus A18(TI/O) A19(CS3) CLKO(A20) 1 17 1 1 1 1 1 1 XTAL EXTAL Oscillator 1 IRQA IRQB Interrupt Request 1 GPIOA0(CS0) Chip Select GPIOA1(CS1) GPIOA2(CS2) 1 1 1 1 1 D0-D12 Data Bus D13-D15/MODEA-C 13 3 1 1 1 1 RD Bus Control WR 1 1 RESET Reset TCK TDI TDO TMS TRST DE JTAG/Enhanced OnCE Figure 2. DSP56852 Signals Identified by Functional Group 1. Specifically for PLL, OSC, and POR. 2. Alternate pin functions are shown in parentheses. 6 DSP56852 Preliminary Technical Data MOTOROLA Introduction Part 3 Signals and Package Information All digital inputs have a weak internal pull-up circuit associated with them. These pull-up circuits are enabled by default. Exceptions: 1. When a pin has GPIO functionality, the pull-up may be disabled under software control. 2. Mode pins D13, D14 and D15 have no pull-up. 3. TCK has a weak pull-down circuit always active. 4. Bidirectional I/O pullups automatically disable when the output is enabled. This table is presented consistently with the Signals Identified by Functional Group figure. 1. BOLD entries in the Type column represents the state of the pin just out of reset. 2. Ouput(Z) means an output in a High-Z condition. Table 3. DSP56852 Signal and Package Information for the 81-pin MAPBGA Pin No. E1 J5 E9 D1 J4 F9 C1 H1 J7 G9 B9 A4 B1 G1 J6 J9 C9 A5 B5 B6 Signal Name VDD VDD VDD VSS VSS VSS VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VSSIO VSSIO VSSIO VSSIO VSSIO VSSIO VDDA VSSA VDDA VSSA Analog Power--These pins supply an analog power source Analog Ground--This pin supplies an analog ground. VSSIO I/O Power - GND--These pins provide grounding for all I/O and ESD structures of the chip and should all be attached to VSS. VDDIO I/O Power --These pins provide power for all I/O and ESD structures of the chip, and should all be attached to VDDIO. VSS Logic Power - GND--These pins provide grounding for the internal structures of the chip and should all be attached to VSS. Type VDD Description Logic Power --These pins provide power to the internal structures of the chip, and should all be attached to VDD. MOTOROLA DSP56852 Preliminary Technical Data 7 Table 3. DSP56852 Signal and Package Information for the 81-pin MAPBGA Pin No. E4 F2 F3 F4 F1 G3 G2 J1 H2 H3 J2 H4 G4 J3 F5 H5 E5 F6 Signal Name A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 TIO0 G5 A18 TIO1 H6 A19 CS3 Output(Z) Input/Output Output(Z) Input/Output Output(Z) Output Address Bus (A17) Timer I/O (0)--Can be programmed as either a timer input source or as a timer output flag. Address Bus (A18) Timer I/O (1)--Can be programmed as either a timer input source or as a timer output flag. Address Bus (A19) External Chip Select 3 --When enabled, a CSx signal is asserted for external memory accesses that fall within a programmable address range. Output clock (CLKO)--User programmable clock out reference Address Bus--A20 D2 CS0 Output Chip Select 0 (CS0) --When enabled, a CSx signal is asserted for external memory accesses that fall within a programmable address range. Port A GPIO (0) --A general purpose IO pin. Type Output(Z) Description Address Bus (A0-A16)--These pins specify a word address for external program or data memory addresses. J8 CLKO A20 Output Output GPIOA0 Input/Output 8 DSP56852 Preliminary Technical Data MOTOROLA Introduction Table 3. DSP56852 Signal and Package Information for the 81-pin MAPBGA Pin No. D3 Signal Name CS1 Type Output Description Chip Select 1 (CS1) --When enabled, a CSx signal is asserted for external memory accesses that fall within a programmable address range. Port A GPIO (1) --A general purpose IO pin. Chip Select 2 (CS2)--When enabled, a CSx signal is asserted for external memory accesses that fall within a programmable address range. Port A GPIO (2) --A general purpose IO pin. Data Bus (D0-D12) --specify the data for external program or data memory accesses. D0-D15 are tri-stated when the external bus is inactive. GPIOA1 C3 CS2 Input/Output Output GPIOA2 G7 H7 H8 G8 H9 F8 F7 G6 E8 E7 E6 D8 D7 D9 C8 A9 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 MODE A D14 MODE B D15 MODE C Input/Output Input/Output Input/Output Data Bus (D13-D15) -- specify the data for external program or data memory accesses. D0-D15 are tri-stated when the external bus is inactive. Mode Select--During the bootstrap process the MODE A, MODE B, and MODE C pins select one of the eight bootstrap modes. These pins are sampled at the end of reset. Note: Any time POR and EXTERNAL resets are active, the state of MODE A, B and C pins get asynchronously transferred to the SIM Control Register [14:12] ($1FFF08) respectively. These bits determine the mode in which the part will boot up. Note: Software and COP resets do not update the SIM Control Register. E2 RD Output Bus Control- Read Enable (RD)--is asserted during external memory read cycles. When RD is asserted low, pins D0-D15 become inputs and an external device is enabled onto the DSP data bus. When RD is deasserted high, the external data is latched inside the DSP. RD can be connected directly to the OE pin of a Static RAM or ROM. MOTOROLA DSP56852 Preliminary Technical Data 9 Table 3. DSP56852 Signal and Package Information for the 81-pin MAPBGA Pin No. E3 Signal Name WR Type Output Description Bus Control-Write Enable (WR)-- is asserted during external memory write cycles. When WR is asserted low, pins D0-D15 become outputs and the DSP puts data on the bus. When WR is deasserted high, the external data is latched inside the external device. When WR is asserted, it qualifies the A0-A15 pins. WR can be connected directly to the WE pin of a Static RAM. SCI Receive Data (RXD)--This input receives byteoriented serial data and transfers it to the SCI receive shift register. Port E GPIO (0)--A general purpose I/O pin. D4 TXD Output(Z) SCI Transmit Data (TXD)--This signal transmits data from the SCI transmit data register. Port E GPIO (1)--A general purpose I/O pin. Port C GPIO (0)--This pin is a General Purpose I/O (GPIO) pin when the SSI is not in use. SSI Transmit Data (STXD)--This output pin transmits serial data from the SSI Transmitter Shift Register. Port C GPIO (1)--This pin is a General Purpose I/O (GPIO) pin when the SSI is not in use. SSI Receive Data (SRXD)--This input pin receives serial data and transfers the data to the SSI Receive Shift Register. SPI Serial Clock (SCLK)--In Master mode, this pin serves as an output, clocking slaved listeners. In Slave mode, this pin serves as the data clock input. Port C GPIO (2)--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. SSI Serial Transfer Clock (STCK)--This bidirectional pin provides the serial bit rate clock for the transmit section of the SSI. The clock signal can be continuous or gated. SPI Slave Select (SS)--In Master mode, this pin is used to arbitrate multiple masters. In Slave mode, this pin is used to select the slave. Port C GPIO (3)--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. SSI Serial Transfer Frame Sync (STFS) --This bidirectional pin is used to count the number of words in a frame while transmitting. A programmable frame rate divider and a word length divider are used for frame rate sync signal generation. B4 RXD Input GPIOE0 Input/Output GPIOE1 B2 GPIOC0 Input/Output Input/Output STXD A2 GPIOC1 Output Input/Output SRXD Input A3 SCLK Input/Output GPIOC2 Input/Output STCK Input/Output B3 SS Input GPIOC3 Input/Output STFS Input/Output 10 DSP56852 Preliminary Technical Data MOTOROLA Introduction Table 3. DSP56852 Signal and Package Information for the 81-pin MAPBGA Pin No. C4 Signal Name MISO Type Input/Output Description SPI Master In/Slave Out (MISO)--This serial data pin is an input to a master device and an output from a slave device. The MISO line of a slave device is placed in the highimpedance state if the slave device is not selected. Port C GPIO (4)--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. SSI Serial Receive Clock (SRCK)--This bidirectional pin provides the serial bit rate clock for the receive section of the SSI. The clock signal can be continuous or gated. SPI Master Out/Slave In (MOSI)--This serial data pin is an output from a master device and an input to a slave device. The master device places data on the MOSI line a half-cycle before the clock edge that the slave device uses to latch the data. Port C GPIO (5)--This pin is a General Purpose I/O (GPIO) pin that can individually be programmed as input or output pin. SSI Serial Receive Frame Sync (SRFS)-- This bidirectional pin is used to count the number of words in a frame while receiving. A programmable frame rate divider and a word length divider are used for frame rate sync signal generation. External Interrupt Request A (IRQA)--The IRQA Schmitt trigger input is a synchronized external interrupt request that indicates that an external device is requesting service. It can be programmed to be level-sensitive or negative-edgetriggered. External Interrupt Request B (IRQB)--The IRQB Schmitt trigger input is an external interrupt request that indicates that an external device is requesting service. It can be programmed to be level-sensitive or negative-edgetriggered. External Crystal Oscillator Input (EXTAL)--This input should be connected to an external crystal. If an external clock source other than a crystal oscillator is used, EXTAL must be tied off. Crystal Oscillator Output (XTAL)--This output connects the internal crystal oscillator output to an external crystal. If an external clock source other than a crystal oscillator is used, XTAL must be used as the input. GPIOC4 Input/Output SRCK Input/Output C5 MOSI Input/ Output (Z) GPIOC5 Input/Output SRFS Input/Output A1 IRQA Input C2 IRQB Input A6 EXTAL Input A7 XTAL Input/Output MOTOROLA DSP56852 Preliminary Technical Data 11 Table 3. DSP56852 Signal and Package Information for the 81-pin MAPBGA Pin No. D5 Signal Name RESET Type Input Description Reset (RESET)--This input is a direct hardware reset on the processor. When RESET is asserted low, the DSP is initialized and placed in the Reset state. A Schmitt trigger input is used for noise immunity. When the RESET pin is deasserted, the initial Chip Operating mode is latched from the D[15:13] pins. The internal reset signal will be deasserted synchronous with the internal clocks, after a fixed number of internal clocks. To ensure complete hardware reset, RESET and TRST should be asserted together. The only exception occurs in a debugging environment when a hardware DSP reset is required and it is necessary not to reset the JTAG/Enhanced OnCE module. In this case, assert RESET, but do not assert TRST. C6 TCK Input Test Clock Input (TCK)--This input pin provides a gated clock to synchronize the test logic and shift serial data to the JTAG/Enhanced OnCE port. The pin is connected internally to a pull-down resistor. Test Data Input (TDI)--This input pin provides a serial input data stream to the JTAG/Enhanced OnCE port. It is sampled on the rising edge of TCK and has an on-chip pull-up resistor. Test Data Output (TDO)--This tri-statable output pin provides a serial output data stream from the JTAG/ Enhanced OnCE port. It is driven in the Shift-IR and ShiftDR controller states, and changes on the falling edge of TCK. Test Mode Select Input (TMS)--This input pin is used to sequence the JTAG TAP controller's state machine. It is sampled on the rising edge of TCK and has an on-chip pullup resistor. Test Reset (TRST)--As an input, a low signal on this pin provides a reset signal to the JTAG TAP controller. To ensure complete hardware reset, TRST should be asserted whenever RESET is asserted. The only exception occurs in a debugging environment, since the Enhanced OnCE/JTAG module is under the control of the debugger. In this case it is not necessary to assert TRST when asserting RESET . Outside of a debugging environment RESET should be permanently asserted by grounding the signal, thus disabling the Enhanced OnCE/JTAG module on the DSP. Debug Even (DE)-- is an open-drain, bidirectional, active low signal. As an input, it is a means of entering Debug mode of operation from an external command controller. As an output, it is a means of acknowledging that the chip has entered Debug mode. B7 TDI Input A8 TDO Output C7 TMS Input D6 TRST Input B8 DE Input/Output 12 DSP56852 Preliminary Technical Data MOTOROLA General Characteristics Part 4 Specifications 4.1 General Characteristics The DSP56852 is fabricated in high-density CMOS with 5-volt tolerant TTL-compatible digital inputs. The term "5-volt tolerant" refers to the capability of an I/O pin, built on a 3.3V compatible process technology, to withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture of devices designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V and 5Vcompatible I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V 10% during normal operation without causing damage). This 5V-tolerant capability therefore offers the power savings of 3.3V I/O levels while being able to receive 5V levels without being damaged. Absolute maximum ratings given in Table 4 are stress ratings only, and functional operation at the maximum is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent damage to the device. The DSP56852 DC/AC electrical specifications are preliminary and are from design simulations. These specifications may not be fully tested or guaranteed at this early stage of the product life cycle. Finalized specifications will be published after complete characterization and device qualifications have been completed. CAUTION This device contains protective circuitry to guard against damage due to high static voltage or electrical fields. However, normal precautions are advised to avoid application of any voltages higher than maximum rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate voltage level. Table 4. Absolute Maximum Ratings Characteristic Supply voltage, core Supply voltage, IO Supply voltage, analog Digital input voltages Analog input voltages (XTAL, EXTAL) Current drain per pin excluding VDD, VSS, VDDA, VSSA,VDDIO, VSSIO Junction temperature Storage temperature range 1. 2. VDD must not exceed VDDIO VDDIO and VDDA must not differ by more that 0.5V Symbol VDD1 VDDIO2 VDDIO2 VIN VINA I Min VSS - 0.3 VSSIO - 0.3 VSSA - 0.3 VSSIO - 0.3 VSSA - 0.3 -- Max VSS + 2.0 VSSIO + 4.0 VDDA + 4.0 VSSIO + 5.5 VDDA + 0.3 10 Unit V V V mA TJ TSTG -40 -55 120 150 C C MOTOROLA DSP56852 Preliminary Technical Data 13 Table 5. Recommended Operating Conditions Characteristic Supply voltage for Logic Power Supply voltage for I/O Power Supply voltage for Analog Power Ambient operating temperature PLL clock frequency1 Operating Frequency2 Frequency of peripheral bus Frequency of external clock Frequency of oscillator Frequency of clock via XTAL Frequency of clock via EXTAL Symbol VDD VDDIO VDDA TA fpll fop fipb fclk fosc fxtal fextal Min 1.62 3.0 3.0 -40 -- -- -- -- 2 -- 2 Max 1.98 3.6 3.6 85 240 120 60 240 4 240 4 Unit V V V C MHz MHz MHz MHz MHz MHz MHz 1. Assumes clock source is direct clock to EXTAL or crystal oscillator running 2-4MHz PLL must be enabled, locked, and selected. The actual frequency depends on the source clock frequency and programming of the CGM module. 2. Master clock is derived from one of the following four sources: fclk = fxtal when the source clock is the direct clock to EXAL fclk = fpll when PLL is selected fclk = fosc when the source clock is the crystal oscillator and PLL is not selected fclk = fextal when the source clock is the direct clock to EXAL and PLL is not selected Table 6. Thermal Characteristics1 81-pin MAPBGA Characteristic Symbol Thermal resistance junction-to-ambient (estimated) I/O pin power dissipation Power dissipation Maximum allowed PD 1. See Section 6.1 for more detail. Value 36.9 User Determined PD = (IDD x VDD) + PI/O (TJ - TA) / JA Unit C/W W W C JA PI/O PD PDMAX 14 DSP56852 Preliminary Technical Data MOTOROLA DC Electrical Characteristics 4.2 DC Electrical Characteristics Table 7. DC Electrical Characteristics Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic Input high voltage (XTAL/EXTAL) Input low voltage (XTAL/EXTAL) Input high voltage Input low voltage Input current low (pullups disabled) Input current high (pullups disabled) Output tri-state current low Output tri-state current high Output High Voltage at IOH Output Low Voltage at IOL Output High Current at VOH Output Low Current at VOL Input capacitance Output capacitance VDD supply current @ nominal voltage and 25 C Run Deep Stop2 Light Stop3 VDDIO supply current @ nominal voltage and 25 C Run5 VDDA supply current @ nominal voltage and 25 C Deep Stop 2 1 Symbol VIHC VILC VIH VIL IIL IIH IOZL IOZH VOH VOL IOH IOL CIN COUT IDD4 Min VDDA - 0.8 -0.3 2.0 -0.3 -1 -1 -10 -10 VDDIO - 0.7 -- 8 8 -- -- Typ VDDA -- -- -- -- -- -- -- -- -- -- -- 8 12 Max VDDA + 0.3 0.5 5.5 0.8 1 1 10 10 -- 0.4 16 16 -- -- Unit V V V V A A A A V V mA mA pF pF -- -- -- IDDIO -- IDDA -- VEI VEIH POR -- -- -- 70 30 2.6 -- -- -- mA A mA 40 -- mA A V mV V 60 2.5 50 1.5 -- 2.85 -- 2.0 Low Voltage Interrupt6 Low Voltage Interrupt Recovery Hysteresis Power on Reset7 1. Run (operating) IDD measured using external square wave clock source (fosc = 4MHz) into XTAL. All inputs 0.2V from rail; no DC loads; outputs unloaded. All ports configured as inputs; measured with all modules enabled. PLL set to 240MHz out. Running Core, performing 50% NOP and 50% FIR. Clock at 120 MHz. 2. Deep Stop Mode - Operation frequency = 4 MHz, PLL set to 4 MHz, crystal oscillator and time of day module operating. 3. Light Stop Mode - Operation frequency = 120 MHz, PLL set to 240 MHz, crystal oscillator and time of day module operating. 4. 5. 6. IDD includes current for core logic, internal memories, and all internal peripheral logic circuitry. Running core and performing external memory access. Clock at 120 MHz. When VDD drops below VEI max value, an interrupt is generated. 7. Power-on reset occurs whenever the digital supply drops below 1.8V. While power is ramping up, this signal remains active as long as the internal 2.5V is below 1.8V, no matter how long the ramp up rate is. The internally regulated voltage is typically 100mV less than VDD during ramp up until 2.5V is reached, at which time it self-regulates. MOTOROLA DSP56852 Preliminary Technical Data 15 4.3 Supply Voltage Sequencing and Separation Cautions Figure 3 shows two situations to avoid in sequencing the VDD and VDDIO, VDDA supplies. 3.3V DC Power Supply Voltage VDDIO, VDDA 2 1.8V Supplies Stable VDD 1 0 Notes: 1. VDD rising before VDDIO, VDDA 2. VDDIO, VDDA rising much faster than VDD Time Figure 3. Supply Voltage Sequencing and Separation Cautions VDD should not be allowed to rise early (1). This is usually avoided by running the regulator for the VDD supply (1.8V) from the voltage generated by the 3.3V VDDIO supply, see Figure 4. This keeps VDD from rising faster than VDDIO. VDD should not rise so late that a large voltage difference is allowed between the two supplies (2). Typically this situation is avoided by using external discrete diodes in series between supplies, as shown in Figure 4. The series diodes forward bias when the difference between VDDIO and VDD reaches approximately 2.1, causing VDD to rise as VDDIO ramps up. When the VDD regulator begins proper operation, the difference between supplies will typically be 0.8V and conduction through the diode chain reduces to essentially leakage current. During supply sequencing, the following general relationship should be adhered to: VDDIO > VDD > (VDDIO - 2.1V) In practice, VDDA is typically connected directly to VDDIO with some filtering. 3.3V Regulator VDDIO, VDDA Supply 1.8V Regulator VDD Figure 4. Example Circuit to Control Supply Sequencing 16 DSP56852 Preliminary Technical Data MOTOROLA AC Electrical Characteristics 4.4 AC Electrical Characteristics Timing waveforms in Section 4.2 are tested with a VIL maximum of 0.8V and a VIH minimum of 2.0V for all pins except XTAL, which is tested using the input levels in Section 4.2. In Figure 5 the levels of VIH and VIL for an input signal are shown. VIH Input Signal Midpoint1 Fall Time Note: The midpoint is VIL + (VIH - VIL)/2. Low High 90% 50% 10% VIL Rise Time Figure 5. Input Signal Measurement References Figure 6 shows the definitions of the following signal states: * * * * Active state, when a bus or signal is driven, and enters a low impedance state Tri-stated, when a bus or signal is placed in a high impedance state Data Valid state, when a signal level has reached VOL or VOH Data Invalid state, when a signal level is in transition between VOL and VOH Data1 Valid Data1 Data Invalid State Data Active Data2 Valid Data2 Data Tri-stated Data3 Valid Data3 Data Active Figure 6. Signal States 4.5 External Clock Operation The DSP56852 system clock can be derived from a crystal or an external system clock signal. To generate a reference frequency using the internal oscillator, a reference crystal must be connected between the EXTAL and XTAL pins. 4.5.1 Crystal Oscillator for use with PLL The internal oscillator is designed to interface with a parallel-resonant crystal resonator in the frequency range specified for the external crystal in Table 9. In Figure 7 a typical crystal oscillator circuit is shown. Follow the crystal supplier's recommendations when selecting a crystal, because crystal parameters determine the component values required to provide maximum stability and reliable start-up. The crystal and associated components should be mounted as close as possible to the EXTAL and XTAL pins to minimize output distortion and start-up stabilization time. MOTOROLA DSP56852 Preliminary Technical Data 17 Crystal Frequency = 2-4MHz (optimized for 4MHz) EXTAL XTAL Rz Sample External Crystal Parameters: Rz = 10M TOD_SEL bit in CGM must be set to 0 Figure 7. Crystal Oscillator 4.5.2 High Speed External Clock Source (> 4MHz) The recommended method of connecting an external clock is given in Figure 8. The external clock source is connected to XTAL and the EXTAL pin is held at ground, VDDA, or VDDA/2. The TOD_SEL bit in CGM must be set to 0. DSP56852 XTAL EXTAL GND,VDDA, External Clock or VDDA/2 (up to 240MHz) Figure 8. Connecting a High Speed External Clock Signal using XTAL 4.5.3 Low Speed External Clock Source (2-4MHz) The recommended method of connecting an external clock is given in Figure 9. The external clock source is connected to XTAL and the EXTAL pin is held at VDDA/2. The TOD_SEL bit in CGM must be set to 0. DSP56852 XTAL EXTAL External Clock (2-4MHz) VDDA/2 Figure 9. Connecting a Low Speed External Clock Signal using XTAL 18 DSP56852 Preliminary Technical Data MOTOROLA External Clock Operation Table 8. External Clock Operation Timing Requirements4 Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic Frequency of operation (external clock driver)1 Clock Pulse Width4 External clock input rise time2, 4 External clock input fall time3, 4 1. 2. 3. 4. Symbol fosc tPW trise tfall Min 0 6.25 -- -- Typ -- -- -- -- Max 240 -- TBD TBD Unit MHz ns ns ns See Figure 8 for details on using the recommended connection of an external clock driver. External clock input rise time is measured from 10 to 90 percent. External clock input fall time is measured from 90 to 10percent. Parameters listed are guaranteed by design. VIH External Clock 90% 50% 10% tPW tPW tfall trise 90% 50% 10% VIL Note: The midpoint is VIL + (VIH - VIL)/2. Figure 10. External Clock Timing Table 9. PLL Timing Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic External reference crystal frequency for the PLL1 PLL output frequency PLL stabilization time 2 Symbol fosc fclk tplls Min 2 40 -- Typ 4 -- 1 Max 4 240 10 Unit MHz MHz ms 1. An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work correctly. The PLL is optimized for 4MHz input crystal. 2. This is the minimum time required after the PLL setup is changed to ensure reliable operation. MOTOROLA DSP56852 Preliminary Technical Data 19 4.6 External Memory InterfaceTiming Table 10. External Memory Interface Timing 1, 2 Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz, TOP = 8.3, FIPB = 60MHz, TIPB = 16.6 Characteristic Address Valid to WR Asserted WR Width Asserted Wait states > 1 D0-D15 Out Valid to WR Asserted Data Out Hold Time from WR Deasserted Data Out Set Up Time to WR Deasserted Wait states > 1 RD Deasserted to Address Not Valid Address Valid to RD Deasserted Wait states > 1 Input Data Hold to RD Deasserted RD Assertion Width Wait states > 1 Address Valid to Input Data Valid Wait states > 1 Address Valid to RD Asserted RD Asserted to Input Data Valid Wait states > 1 WR Deasserted to RD Asserted RD Deasserted to RD Asserted WR Deasserted to WR Asserted RD Deasserted to WR Asserted Symbol tAWR tWR Typical Min 4.61 Typical Max -- Unit ns (TIPB*WS)-.84 tWRD tDOH tDOS (TIPB*WS)+4.66 tRDA tARDD (TIPB*WS) -2.18 tDRD tRD (TIPB*WS) -1.25 tAD -- tARDA tRDD -- tWRRD4 tRDRD4 tWRWR4 tRDWR4 TOP TOP x 2 TOP x 2 TOP x 3 - 2.33 0 12.39 4.50 5.38 -- -- -- ns ns ns -- -- -- ns ns ns -- ns -- ns (TIPB*WS) -19.22 -- ns ns (TIPB*WS) - 17.89 -- -- -- -- ns ns ns ns ns 1. Timing is both wait state and frequency dependent. In the formulas listed, WS = the number of wait states (min.1 ) and TOP = System Clock Period. For fop = 120MHz operation and TIPB 6 = Peripheral Clock Period for fipb = 60MHz 2. 3. Parameters listed are guaranteed by design. EMI operates at fipb rate. Wait states are in terms of fipb periods. 4. Shows separation of R/W enables in system cycles ( Top ) in data space using consecutive one-word assembly language instructions. 20 DSP56852 Preliminary Technical Data MOTOROLA Reset, Stop, Wait, Mode Select, and Interrupt Timing A0-A20, CS (See Note) tARDA tARDD tRDA tRDRD RD tAWR tWRWR tWR tWRRD tRD tRDWR WR tWRD tDOS tAD tDOH tRDD tDRD D0-D15 Data Out Data In Note: During read-modify-write instructions and internal instructions, the address lines do not change state. Figure 11. External Bus Asynchronous Timing 4.7 Reset, Stop, Wait, Mode Select, and Interrupt Timing Table 11. Reset, Stop, Wait, Mode Select, and Interrupt Timing 1, 2 Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic RESET Assertion to Address, Data and Control Signals High Impedance Minimum RESET Assertion Duration3 RESET Deassertion to First External Address Output Edge-sensitive Interrupt Request Width IRQA, IRQB Assertion to External Data Memory Access Out Valid, caused by first instruction execution in the interrupt service routine IRQA, IRQB Assertion to General Purpose Output Valid, caused by first instruction execution in the interrupt service routine IRQA Low to First Valid Interrupt Vector Address Out recovery from Wait State4 Symbol tRAZ Typical Min -- Typica l Max 11 Unit ns See Figure Figure 12 tRA tRDA tIRW tIDM 30 -- 1T + 3 -- -- 120T -- 18T ns ns ns ns Figure 12 Figure 12 Figure 13 Figure 14 tIG -- 18T ns Figure 14 tIRI -- 13T ns Figure 15 MOTOROLA DSP56852 Preliminary Technical Data 21 Table 11. Reset, Stop, Wait, Mode Select, and Interrupt Timing (Continued)1, 2 Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic IRQA Width Assertion to Recover from Stop State5 Fast6 Normal7 Symbol tIW Typical Min Typica l Max Unit See Figure Figure 16 4T 8ET tIF -- -- tRSTO 128ET 8ET -- -- ns ns Figure 16 Delay from IRQA Assertion to Fetch of first instruction (exiting Stop) Fast6 Normal7 RSTO pulse width8 normal operation internal reset mode 1. 2. 13T 25ET ns ns Figure 17 -- -- -- -- In the formulas, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns. Parameters listed are guaranteed by design. 3. At reset, the PLL is disabled and bypassed. The part is then put into run mode and tclk assumes the period of the source clock, txtal, textal or tosc. 4. The minimum is specified for the duration of an edge-sensitive IRQA interrupt required to recover from the Stop state. This is not the minimum required so that the IRQA interrupt is accepted. 5. 6. The interrupt instruction fetch is visible on the pins only in Mode 3. Fast stop mode: Fast stop recovery applies when external clocking is in use (direct clocking to XTAL) or when fast stop mode recovery is requested (OMR bit 6 is set to 1). In both cases the PLL and the master clock are unaffected by stop mode entry. Recovery takes one less cycle and tclk will continue same value it had before stop mode was entered. 7. Normal stop mode: As a power saving feature, normal stop mode disables and bypasses the PLL. Stop mode will then shut down the master clock, recovery will take an extra cycle (to restart the clock), and tclk will resume at the input clock source rate. 8. ET = External Clock period, For an external crystal frequency of 8MHz, ET=125 ns. RESET tRA tRAZ tRDA A0-A20, D0-D15 CS, RD, WR First Fetch First Fetch Figure 12. Asynchronous Reset Timing 22 DSP56852 Preliminary Technical Data MOTOROLA Reset, Stop, Wait, Mode Select, and Interrupt Timing IRQA IRQB tIRW Figure 13. External Interrupt Timing (Negative-Edge-Sensitive) A0-A20, CS, RD, WR tIDM First Interrupt Instruction Execution IRQA, IRQB a) First Interrupt Instruction Execution Purpose I/O Pin IRQA, IRQB tIG b) General Purpose I/O Figure 14. External Level-Sensitive Interrupt Timing IRQA, IRQB tIRI A0-A20, CS, RD, WR First Interrupt Vector Instruction Fetch Figure 15. Interrupt from Wait State Timing MOTOROLA DSP56852 Preliminary Technical Data 23 tIW IRQA tIF A0-A20, CS, RD, WR First Instruction Fetch Not IRQA Interrupt Vector Figure 16. Recovery from Stop State Using Asynchronous Interrupt Timing RESET tRSTO Figure 17. Reset Output Timing 4.8 Serial Peripheral Interface (SPI) Timing Table 12. SPI Timing1 Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic Cycle time Master Slave Enable lead time Master Slave Enable lag time Master Slave Clock (SCLK) high time Master Slave Clock (SCLK) low time Master Slave Symbol tC Min Max Unit See Figure Figures 18, 19, 20, 21 Figure 21 25 25 tELD -- 12.5 tELG -- 12.5 tCH 9 12.5 tCL 12 12.5 -- -- -- -- -- -- -- -- -- -- ns ns ns ns Figure 21 ns ns ns ns Figures 18, 19, 20, 21 Figure 21 ns ns 24 DSP56852 Preliminary Technical Data MOTOROLA Serial Peripheral Interface (SPI) Timing Table 12. SPI Timing1 Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Data setup time required for inputs Master Slave Data hold time required for inputs Master Slave Access time (time to data active from high-impedance state) Slave Disable time (hold time to high-impedance state) Slave Data Valid for outputs Master Slave (after enable edge) Data invalid Master Slave Rise time Master Slave Fall time Master Slave 1. Parameters listed are guaranteed by design. tDS 10 2 tDH 0 2 tA 5 tD 2 tDV -- -- tDI 0 0 tR -- -- tF -- -- 9.7 9.0 ns ns 11.5 10.0 ns ns -- -- ns ns 2 14 ns ns 9 15 -- -- ns ns ns ns ns ns -- -- ns ns Figures 18, 19, 20, 21 Figures 18, 19, 20, 21 Figure 21 Figure 21 Figures 18, 19, 20, 21 Figures 18, 19, 20, 21 Figures 18, 19, 20, 21 Figures 18, 19, 20, 21 MOTOROLA DSP56852 Preliminary Technical Data 25 SS (Input) SS is held High on master tC tR tF SCLK (CPOL = 0) (Output) tCL tCH tF tR tCL SCLK (CPOL = 1) (Output) tDH tDS tCH tCH MISO (Input) MSB in tDI Bits 14-1 tDV LSB in tDI(ref) MOSI (Output) Master MSB out tF Bits 14-1 Master LSB out tR Figure 18. SPI Master Timing (CPHA = 0) SS (Input) tC SS is held High on master tF tCL tR SCLK (CPOL = 0) (Output) tCH tF tCL SCLK (CPOL = 1) (Output) tCH tDS tR tDH MISO (Input) tDV(ref) MSB in tDI Bits 14-1 tDV LSB in MOSI (Output) Master MSB out tF Bits 14- 1 Master LSB out tR Figure 19. SPI Master Timing (CPHA = 1) 26 DSP56852 Preliminary Technical Data MOTOROLA Serial Peripheral Interface (SPI) Timing SS (Input) tC tCL tCH tELD tCL tR tF tELG SCLK (CPOL = 0) (Input) SCLK (CPOL = 1) (Input) tA tCH tR tF tD MISO (Output) tDS Slave MSB out tDH Bits 14-1 tDV Slave LSB out tDI tDI MOSI (Input) MSB in Bits 14-1 LSB in Figure 20. SPI Slave Timing (CPHA = 0) SS (Input) tF tC tR tCL tCH tELD tELG tCL tDV tA tCH tF tR tD SCLK (CPOL = 0) (Input) SCLK (CPOL = 1) (Input) MISO (Output) tDS Slave MSB out Bits 14-1 tDV tDH Slave LSB out tDI MOSI (Input) MSB in Bits 14-1 LSB in Figure 21. SPI Slave Timing (CPHA = 1) MOTOROLA DSP56852 Preliminary Technical Data 27 4.9 Quad Timer Timing Table 13. Timer Timing1, 2 Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic Timer input period Timer input high/low period Timer output period Timer output high/low period 1. 2. Symbol PIN PINHL POUT POUTHL Min 2T + 3 1T + 3 2T - 3 1T - 3 Max -- -- -- -- Unit ns ns ns ns In the formulas listed, T = clock cycle. For fop = 120MHz operation and fipb = 60MHz, T = 8.33ns Parameters listed are guaranteed by design. Timer Inputs PIN PINHL PINHL Timer Outputs POUT POUTHL POUTHL Figure 22. Timer Timing 28 DSP56852 Preliminary Technical Data MOTOROLA Synchronous Serial Interface (SSI) Timing 4.10 Synchronous Serial Interface (SSI) Timing Table 14. SSI Master Mode1 Switching Characteristics Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Parameter STCK frequency STCK period3 STCK high time STCK low time Output clock rise/fall time Delay from STCK high to STFS (bl) high - Master4 Delay from STCK high to STFS (wl) high - Master4 Delay from SRCK high to SRFS (bl) high - Master4 Delay from SRCK high to SRFS (wl) high - Master4 Delay from STCK high to STFS (bl) low - Master4 Delay from STCK high to STFS (wl) low - Master4 Delay from SRCK high to SRFS (bl) low - Master4 Delay from SRCK high to SRFS (wl) low - Master4 STCK high to STXD enable from high impedance - Master STCK high to STXD valid - Master STCK high to STXD not valid - Master STCK high to STXD high impedance - Master SRXD Setup time before SRCK low - Master SRXD Hold time after SRCK low - Master Symbol fs tSCKW tSCKH tSCKL Min Typ Max 152 Units MHz ns ns ns 66.7 33.4 33.4 4 ns -0.1 -0.1 1.0 1.0 -0.1 -0.1 0.1 0.1 1 1 0 0 ns ns ns ns ns ns ns ns ns ns ns ns ns ns tTFSBHM tTFSWHM tRFSBHM tRFSWHM tTFSBLM tTFSWLM tRFSBLM tRFSWLM tTXEM tTXVM tTXNVM tTXHIM tSM tHM -1.0 -1.0 0.1 0.1 -1.0 -1.0 -0.1 -0.1 0 0 -0.1 -4 4 4 Synchronous Operation (in addition to standard internal clock parameters) SRXD Setup time before STCK low - Master SRXD Hold time after STCK low - Master 1. 2. Master mode is internally generated clocks and frame syncs Max clock frequency is IP_clk/4 = 60MHz / 4 = 15MHz for a 120MHz part. tTSM tTHM 4 4 3. All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP=0 in SCR2 and RSCKP=0 in SCSR) and a non-inverted frame sync (TFSI=0 in SCR2 and RFSI=0 in SCSR). If the polarity of the clock and/or the frame sync has been inverted, all the timings remain valid by inverting the clock signal STCK/SRCK and/or the frame sync STFS/SRFS in the tables and in the figures. 4. bl = bit length; wl = word length MOTOROLA DSP56852 Preliminary Technical Data 29 tSCKW tSCKH tSCKL STCK output tTFSBHM STFS (bl) output tTFSWHM STFS (wl) output tTXVM tTXEM STXD SRCK output tRFSBHM SRFS (bl) output tRFSWHM SRFS (wl) output tTSM tSM SRXD tHM tTHM tRFSWLM tRFBLM First Bit tTFSWLM tTFSBLM tTXNVM Last Bit tTXHIM Figure 23. Master Mode Timing Diagram Table 15. SSI Slave Mode1 Switching Characteristics Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Parameter STCK frequency STCK period3 STCK high time STCK low time Output clock rise/fall time Delay from STCK high to STFS (bl) high - Slave5 Delay from STCK high to STFS (wl) high - Slave5 Symbol fs tSCKW tSCKH tSCKL Min Typ Max 152 Units MHz ns ns ns 66.7 33.44 33.44 4 ns 29 29 ns ns tTFSBHS tTFSWHS -1 -1 30 DSP56852 Preliminary Technical Data MOTOROLA Synchronous Serial Interface (SSI) Timing Table 15. SSI Slave Mode1 Switching Characteristics (Continued) Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Parameter Delay from SRCK high to SRFS (bl) high - Slave5 Delay from SRCK high to SRFS (wl) high - Slave5 Delay from STCK high to STFS (bl) low - Slave5 Delay from STCK high to STFS (wl) low - Slave5 Delay from SRCK high to SRFS (bl) low - Slave5 Delay from SRCK high to SRFS (wl) low - Slave5 STCK high to STXD enable from high impedance - Slave STCK high to STXD valid - Slave STFS high to STXD enable from high impedance (first bit) Slave STFS high to STXD valid (first bit) - Slave STCK high to STXD not valid - Slave STCK high to STXD high impedance - Slave SRXD Setup time before SRCK low - Slave SRXD Hold time after SRCK low - Slave Symbol tRFSBHS tRFSWHS tTFSBLS tTFSWLS tRFSBLS tRFSWLS tTXES tTXVS tFTXES tFTXVS tTXNVS tTXHIS tSS tHS Min -1 -1 -29 -29 -29 -29 -- 4 4 4 4 4 4 4 Typ Max 29 29 29 29 29 29 15 15 15 15 15 15 -- -- Units ns ns ns ns ns ns ns ns ns ns ns ns ns ns Synchronous Operation (in addition to standard external clock parameters) SRXD Setup time before STCK low - Slave SRXD Hold time after STCK low - Slave 1. 2. Slave mode is externally generated clocks and frame syncs Max clock frequency is IP_clk/4 = 60MHz / 4 = 15MHz for a 120MHz part. tTSS tTHS 4 4 -- -- ? ? 3. All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP=0 in SCR2 and RSCKP=0 in SCSR) and a non-inverted frame sync (TFSI=0 in SCR2 and RFSI=0 in SCSR). If the polarity of the clock and/or the frame sync has been inverted, all the timings remain valid by inverting the clock signal STCK/SRCK and/or the frame sync STFS/SRFS in the tables and in the figures. 4. 5. 50 percent duty cycle bl = bit length; wl = word length MOTOROLA DSP56852 Preliminary Technical Data 31 tSCKW tSCKH STCK input tTFSBLS tTFSBHS STFS (bl) input tTFSWHS STFS (wl) input tFTXES tTXVS tTXES STXD SRCK input tRFSBHS SRFS (bl) input tRFSWHS SRFS (wl) input tTSS tRFSWLS tRFSBLS First Bit tFTXVS tTXNVS tTXHIS Last Bit tTFSWLS tSCKL tSS SRXD tHS tTHS Figure 24. Slave Mode Clock Timing 4.11 Serial Communication Interface (SCI) Timing Table 16. SCI Timing4 Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic Baud Rate1 RXD2 Pulse Width TXD3 Pulse Width 1. 2. 3. 4. Symbol BR RXDPW TXDPW Min -- 0.965/BR 0.965/BR Max (fMAX)/(32) 1.04/BR 1.04/BR Unit Mbps ns ns fMAX is the frequency of operation of the system clock in MHz. The RXD pin in SCI0 is named RXD0 and the RXD pin in SCI1 is named RXD1. The TXD pin in SCI0 is named TXD0 and the TXD pin in SCI1 is named TXD1. Parameters listed are guaranteed by design. 32 DSP56852 Preliminary Technical Data MOTOROLA JTAG Timing RXD SCI receive data pin (Input) RXDPW Figure 25. RXD Pulse Width TXD SCI receive data pin (Input) TXDPW Figure 26. TXD Pulse Width MSCAN_RX CAN receive data pin (Input) T WAKE-UP Figure 27. Bus Wakeup Detection 4.12 JTAG Timing Table 17. JTAG Timing1, 3 Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.62-1.98V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic TCK frequency of operation2 TCK cycle time TCK clock pulse width TMS, TDI data setup time TMS, TDI data hold time TCK low to TDO data valid TCK low to TDO tri-state TRST assertion time DE assertion time Symbol fOP tCY tPW tDS tDH tDV tTS tTRST tDE Min DC 33.3 16.6 3 3 -- -- 35 4T Max 30 -- -- -- -- 12 10 -- -- Unit MHz ns ns ns ns ns ns ns ns 1. Timing is both wait state and frequency dependent. For the values listed, T = clock cycle. For120MHz operation, T = 8.33 ns 2. 3. TCK frequency of operation must be less than 1/4 the processor rate. Parameters listed are guaranteed by design. MOTOROLA DSP56852 Preliminary Technical Data 33 tCY tPW VIH tPW VM TCK (Input) VM = VIL + (VIH - VIL)/2 VM VIL Figure 28. Test Clock Input Timing Diagram TCK (Input) tDS tDH TDI TMS (Input) TDO (Output) Input Data Valid tDV Output Data Valid tTS TDO (Output) tDV TDO (Output) Output Data Valid Figure 29. Test Access Port Timing Diagram TRST (Input) tTRST Figure 30. TRST Timing Diagram DE tDE Figure 31. Enhanced OnCE--Debug Event 34 DSP56852 Preliminary Technical Data MOTOROLA GPIO Timing 4.13 GPIO Timing Table 18. GPIO Timing Operating Conditions: VSS = VSSIO = VSSA = 0V, VDD = 1.7-1.9V, VDDIO = VDDA = 3.0-3.6V, TA = -40 to +120C, CL 50pF, fop = 120MHz Characteristic GPIO input period GPIO input high/low period GPIO output period GPIO output high/low period Symbol PIN PINHL POUT POUTHL Min 2T + 3 1T + 3 2T - 3 1T - 3 Max -- -- -- -- Unit ns ns ns ns GPIO Inputs PIN PINHL PINHL GPIO Outputs POUT POUTHL POUTHL Figure 32. GPIO Timing MOTOROLA DSP56852 Preliminary Technical Data 35 Part 5 DSP56852 Packaging & Pinout Information This section contains package and pin-out information for the 81-pin MAPBGA configuration of the DSP56852. METALLIZED MARK FOR PIN 1 IDENTIFICATION IN THIS AREA 9 8 7 6 5 4 3 2 1 A D15 TD0 XTAL EXTAL VSSIO VDDIO SCK GPIOC1 IRQA B VDDIO DE TDI VSSA VDDA RXD SS GPIOC0 VSSIO C VSSIO D14 TMS TCK MOSI MISO CS2 IRQB VDDIO D D13 D11 D12 TRST RESET TXD CS1 CS0 VSS E VDD D8 D9 D10 A16 A0 WR RD VDD F VSS D5 D6 A17 A14 A3 A2 A1 A4 G VDDIO D3 D0 D7 A18 A12 A5 A6 VSSIO H D4 D2 D1 A19 A15 A11 A9 A8 VDDIO J VSSIO CLKO VDDIO VSSIO VDD VSS A13 A10 A7 Figure 33. Bottom-View, DSP56852 81-pin MAPBGA Package 36 DSP56852 Preliminary Technical Data MOTOROLA GPIO Timing Table 19. DSP56852 Pin Identification by Pin Number Pin No. E4 F2 F3 F4 F1 G3 G2 J1 H2 H3 J2 H4 G4 J3 F5 H5 E5 F6 G5 H6 J8 Signal Name A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 CLKO Pin No. D2 D3 C3 G7 H7 H8 G8 H9 F8 F7 G6 E8 E7 E6 D8 D7 D9 C8 A9 B8 Signal Name CS0 CS1 CS2 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 DE Pin No. A6 B6 D1 J4 F9 B1 G1 J6 J9 C9 A5 A1 C2 C4 C5 B5 E1 J5 E9 C1 Signal Name EXTAL VSSA VSS VSS VSS VSSIO VSSIO VSSIO VSSIO VSSIO VSSIO IRQA IRQB MISO MOSI VDDA VDD VDD VDD VDDIO Pin No. H1 J7 G9 B9 A4 E2 D5 B4 A3 A2 B3 B2 C6 B7 A8 C7 D6 D4 E3 A7 Signal Name VDDIO VDDIO VDDIO VDDIO VDDIO RD RESET RXD SCK GPIOC1 SS GPIOC0 TCK TDI TDO TMS TRST TXD WR XTAL - MOTOROLA DSP56852 Preliminary Technical Data 37 X Y D LASER MARK FOR PIN 1 IDENTIFICATION IN THIS AREA Detail K M E NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSION b IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER, PARALLEL TO DATUM PLANE Z. 4. DATUM Z (SEATING PLANE) IS DEFINED BY THE SPHERICAL CROWNS OF THE SOLDER BALLS. 5. PARALLELISM MEASUREMENT SHALL EXCLUDE ANY EFFECT OF MARK ON TOP SURFACE OF PACKAGE. 0.20 MILLIMETERS DIM MIN MAX A 0.95 1.3 A1 0.2 0.34 A2 0.96 REF b 0.3 0.5 D 8.00 BSC E 8.00 BSC e 0.80 BSC 8X 9 8 7 6 3 2 e 1 METALIZED MARK FOR PIN 1 IDENTIFICATION IN THIS AREA A B 8X e C D E F G H J 5 A A2 0.30 Z A1 160X Z 4 0.15 Z 3 81X ROTATED 90 CLOCKWISE DETAIL K b 0.25 M Z X Y 0.10 M Z VIEW M-M CASE 1224B-01 ISSUE A DATE 06/30/00 Figure 34. 81-pin MAPBGA Mechanical Information 38 DSP56852 Preliminary Technical Data MOTOROLA Thermal Design Considerations Part 6 Design Considerations 6.1 Thermal Design Considerations An estimation of the chip junction temperature, TJ, in C can be obtained from the equation: Equation 1: Where: TA = ambient temperature C RJA = package junction-to-ambient thermal resistance C/W PD = power dissipation in package Historically, thermal resistance has been expressed as the sum of a junction-to-case thermal resistance and a case-to-ambient thermal resistance: Equation 2: Where: RJA = package junction-to-ambient thermal resistance C/W RJC = package junction-to-case thermal resistance C/W RCA = package case-to-ambient thermal resistance C/W RJC is device-related and cannot be influenced by the user. The user controls the thermal environment to change the case-to-ambient thermal resistance, RCA. For example, the user can change the air flow around the device, add a heat sink, change the mounting arrangement on the Printed Circuit Board (PCB), or otherwise change the thermal dissipation capability of the area surrounding the device on the PCB. This model is most useful for ceramic packages with heat sinks; some 90% of the heat flow is dissipated through the case to the heat sink and out to the ambient environment. For ceramic packages, in situations where the heat flow is split between a path to the case and an alternate path through the PCB, analysis of the device thermal performance may need the additional modeling capability of a system level thermal simulation tool. The thermal performance of plastic packages is more dependent on the temperature of the PCB to which the package is mounted. Again, if the estimations obtained from RJA do not satisfactorily answer whether the thermal performance is adequate, a system level model may be appropriate. A complicating factor is the existence of three common definitions for determining the junction-to-case thermal resistance in plastic packages: * Measure the thermal resistance from the junction to the outside surface of the package (case) closest to the chip mounting area when that surface has a proper heat sink. This is done to minimize temperature variation across the surface. Measure the thermal resistance from the junction to where the leads are attached to the case. This definition is approximately equal to a junction to board thermal resistance. Use the value obtained by the equation (TJ - TT)/PD where TT is the temperature of the package case determined by a thermocouple. RJA = RJC + RCA TJ = TA + (PD x RJA) * * As noted above, the junction-to-case thermal resistances quoted in this data sheet are determined using the first definition. From a practical standpoint, that value is also suitable for determining the junction temperature from a case thermocouple reading in forced convection environments. In natural convection, using the junction-to-case thermal resistance to estimate junction temperature from a thermocouple reading MOTOROLA DSP56852 Preliminary Technical Data 39 on the case of the package will estimate a junction temperature slightly hotter than actual. Hence, the new thermal metric, Thermal Characterization Parameter, or JT, has been defined to be (TJ - TT)/PD. This value gives a better estimate of the junction temperature in natural convection when using the surface temperature of the package. Remember that surface temperature readings of packages are subject to significant errors caused by inadequate attachment of the sensor to the surface and to errors caused by heat loss to the sensor. The recommended technique is to attach a 40-gauge thermocouple wire and bead to the top center of the package with thermally conductive epoxy. 6.2 Electrical Design Considerations CAUTION This device contains protective circuitry to guard against damage due to high static voltage or electrical fields. However, normal precautions are advised to avoid application of any voltages higher than maximum rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate voltage level. Use the following list of considerations to assure correct DSP operation: * * Provide a low-impedance path from the board power supply to each VDD pin on the DSP, and from the board ground to each VSS (GND) pin. The minimum bypass requirement is to place six 0.01-0.1F capacitors positioned as close as possible to the package supply pins. The recommended bypass configuration is to place one bypass capacitor on each of the ten VDD/VSS pairs, including VDDA/VSSA. Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND) pins are less than 0.5 inch per capacitor lead. Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for VDD and GND. Bypass the VDD and GND layers of the PCB with approximately 100F, preferably with a highgrade capacitor such as a tantalum capacitor. Because the DSP output signals have fast rise and fall times, PCB trace lengths should be minimal. Consider all device loads as well as parasitic capacitance due to PCB traces when calculating capacitance. This is especially critical in systems with higher capacitive loads that could create higher transient currents in the VDD and GND circuits. All inputs must be terminated (i.e., not allowed to float) using CMOS levels. Take special care to minimize noise levels on the VDDA and VSSA pins. When using Wired-OR mode on the SPI or the IRQx pins, the user must provide an external pullup device. * * * * * * * * 40 DSP56852 Preliminary Technical Data MOTOROLA Electrical Design Considerations * Designs that utilize the TRST pin for JTAG port or Enhance OnCE module functionality (such as development or debugging systems) should allow a means to assert TRST whenever RESET is asserted, as well as a means to assert TRST independently of RESET. Designs that do not require debugging functionality, such as consumer products, should tie these pins together. The internal POR (Power on Reset) will reset the part at power on with reset asserted or pulled high but requires that TRST be asserted at power on. * Part 7 Ordering Information Table 20 lists the pertinent information needed to place an order. Consult a Motorola Semiconductor sales office or authorized distributor to determine availability and to order parts. Table 20. DSP56852 Ordering Information Part DSP56852 Supply Voltage 1.8-3.3 V Package Type Mold Array Process Ball Grid Array (MAPBGA) Pin Count 81 Frequency (MHz) 120 Order Number DSP56852VF120 MOTOROLA DSP56852 Preliminary Technical Data 41 42 DSP56852 Preliminary Technical Data MOTOROLA Electrical Design Considerations MOTOROLA DSP56852 Preliminary Technical Data 43 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and the Stylized M Logo are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. (c) Motorola, Inc. 2002. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3-20-1, Minami-Azabu. Minato-ku, Tokyo 106-8573 Japan. 81-3-3440-3569 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. 852-26668334 Technical Information Center: 1-800-521-6274 HOME PAGE: http://www.motorola.com/semiconductors/ DSP56852/D |
Price & Availability of DSP56852
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |