 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Microcomputer Components 8-Bit CMOS Microcontroller SAB-C513A-L16P 16 MHz Specification Data Sheet Addendum 03.97 SAB-C513A-L16P 16 MHz Specification Ordering Information Type SAB-C513A-L16P Ordering Code Q67120-C1039 Package P-DIP-40 Description (8-Bit CMOS Microcontroller) for external memory, 16 MHz T2 / P1.0 T2EX / P1.1 SCLK / P1.2 SRI / P1.3 STO / P1.4 SLS / P1.5 P1.6 P1.7 RESET RXD / P3.0 TXD / P3.1 INT0 / P3.2 INT1 / P3.3 T0 / P3.4 T1 / P3.5 WR / P3.6 RD / P3.7 XTAL2 XTAL1 VSS 1 40 SABC513A-L16P 20 21 VCC P0.0 / AD0 P0.1 / AD1 P0.2 / AD2 P0.3 / AD3 P0.4 / AD4 P0.5 / AD5 P0.6 / AD6 P0.7 / AD7 EA ALE PSEN P2.7 / A15 P2.6 / A14 P2.5 / A13 P2.4 / A12 P2.3 / A11 P2.2 / A10 P2.1 / A9 P2.0 / A8 Pin Configuration (Top view) Semiconductor Group 2 SAB-C513A-L16P 16 MHz Specification DC Characteristics VCC = 4.0 - 5.5V; VSS = 0 V; TA = 0 to + 70 C Parameter Power supply current: Active mode, 16 MHz 6) Idle mode, 16 MHz 6) Power Down Mode Notes: 3) Symbol typ. Limit Values 8) Unit Test Condition max. 14.3 5.6 50 mA mA A ICC ICC IPD 11 4.3 - VCC = 5 V,4) VCC = 5 V,5) VCC = 2 ... 5.5 V 3) IPD (Power Down Mode) is measured under following conditions: EA = Port0 = VCC; RESET = VSS; XTAL2 = N.C.; XTAL1 = VCC; all other pins are disconnected. ICC (active mode) is measured with: XTAL1 driven with tCLCH, tCHCL = 5 ns, VIL = VSS + 0.5 V, VIH = VCC - 0.5 V; XTAL2 = N.C.; EA = Port0 = RESET = VCC; all other pins are disconnected. ICC would be slightly higher if a crystal oscillator is used (appr. 1 mA). 4) 5) ICC (Idle mode) is measured with all output pins disconnected and with all peripherals disabled; XTAL1 driven with tCLCH, tCHCL = 5 ns, VIL = VSS + 0.5 V, VIH = VCC - 0.5 V; XTAL2 = N.C.; RESET = EA = VSS ; Port0 = VCC; all other pins are disconnected; ICC Max at other frequencies is given by: Active mode : ICC = 0.85 x fOSC + 0.72 Idle mode : ICC = 0.34 x fOSC + 0.15 where fOSC is the oscillator frequency in MHz. ICC values are given in mA and measured at VCC = 5 V. The typical 6) 8) ICC values are periodically measured at TA = +25 C but not 100% tested. Semiconductor Group 3 SAB-C513A-L16P 16 MHz Specification AC Characteristics VCC = 4.0 - 5.5V; VSS = 0 V; TA = 0 to + 70 C (CL for port 0, ALE and PSEN outputs = 100 pF; CL for all other outputs = 80 pF) Program Memory Characteristics Parameter Symbol 16 MHz Clock min. ALE pulse width Address setup to ALE Address hold after ALE ALE low to valid instr in ALE to PSEN PSEN pulse width PSEN to valid instr in Input instruction hold after PSEN Input instruction float after PSEN Address valid after PSEN Address to valid instr in Address float to PSEN max. - - - 150 - - 88 - 43 - 198 - Limit Values Variable Clock 1/tCLCL = 3.5 MHz to 16 MHz min. 2tCLCL - 40 max. - - - 4tCLCL - 100 - - 3tCLCL - 100 - ns ns ns ns ns ns ns ns ns ns ns ns Unit tLHLL tAVLL tLLAX tLLIV tLLPL tPLPH tPLIV tPXIX tPXIZ*) tPXAV*) tAVIV tAZPL 85 33 28 - 38 153 - 0 - 55 - 0 tCLCL - 30 tCLCL - 35 - tCLCL - 25 3tCLCL - 35 - 0 - tCLCL - 20 - 5tCLCL - 115 - tCLCL - 8 - 0 *) Interfacing the C513 microcontroller to devices with float times up to 55 ns is permissible. This limited bus contention will not cause any damage to port 0 drivers. Semiconductor Group 4 SAB-C513A-L16P 16 MHz Specification External Data Memory Characteristics Parameter Symbol 16 MHz Clock min. RD pulse width WR pulse width Address hold after ALE RD to valid data in Data hold after RD Data float after RD ALE to valid data in Address to valid data in ALE to WR or RD Address valid to WR or RD WR or RD high to ALE high Data valid to WR transition Data setup before WR Data hold after WR Address float after RD max. - - - 148 - 55 350 398 238 - 103 - - - 0 Limit Values Variable Clock 1/tCLCL = 3.5 MHz to 16 MHz min. 6tCLCL - 100 6tCLCL - 100 max. - - - 5tCLCL - 165 - 2tCLCL - 70 8tCLCL - 150 9tCLCL - 165 3tCLCL + 50 - ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Unit tRLRH tWLWH tLLAX2 tRLDV tRHDX tRHDZ tLLDV tAVDV tLLWL tAVWL tWHLH tQVWX tQVWH tWHQX tRLAZ 275 275 90 - 0 - - - 138 120 23 13 288 13 - 2tCLCL - 35 - 0 - - - 3tCLCL - 50 4tCLCL - 130 tCLCL - 40 tCLCL - 50 7tCLCL - 150 tCLCL + 40 - - - 0 tCLCL - 50 - Semiconductor Group 5 SAB-C513A-L16P 16 MHz Specification SSC Interface Characteristics Parameter Symbol Limit Values 13.5 MHz Clock min. Clock Cycle Time : Master Mode Slave Mode Clock high time Clock low time Data output delay Data output hold Data input setup Data input hold TC bit set delay max. - - - - 100 - - - 16 tCLCL 16 MHz Clock min. 500 450 200 200 - 0 80 80 - - - - - 100 - - - 16 tCLCL ns ns ns ns ns ns ns ns ns Unit tSCLK tSCLK tSCH tSCL tD tHO tS tHI tDTC 592 530 230 230 - 0 100 100 - External Clock Characteristics Parameter Symbol Limit Values Variable Clock Freq. = 3.5 MHz to 16 MHz min. Oscillator period High time Low time Rise time Fall time max. 285 ns ns ns ns ns Unit tCLCL tCHCX tCLCX tCLCH tCHCL 62.5 15 15 - - tCLCL - tCLCX tCLCL - tCHCX 15 15 Reset Characteristics Parameter Symbol 16 MHz Clock min. RESET high pulse width (when CPU is running) max. - Limit Values Variable Clock 1/tCLCL = 3.5 MHz to 16 MHz min. 24 tCLCL max. - s Unit tRES 1.5 Semiconductor Group 6 SAB-C513A-L16P 16 MHz Specification Recommended Oscillator Circuits Crystal Oscillator Mode Driving from External Source C XTAL2 3.5 - 16 MHz XTAL1 N.C. XTAL2 External Oscillator Signal XTAL1 C C = 20 pF 10 pF (incl. stray capacitance) Package Outline Plastic Package, P-DIP-40-2 (Plastic Dual in-Line Package) Semiconductor Group 7 |
Price & Availability of D513A16
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |