View 9609_972562.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
VN340SP(8933)
QUAD HIGH SIDE SMART POWER SOLID STATE RELAY
TYPE Vdemag(*) RDSon (*) IOUT (*) VCC VN340SP(8933) VCC-55V 0.2 1A 36 V
(*) Per channel
n OUTPUT CURRENT: 1A PER CHANNEL n DIGITAL I/O's CLAMPED AT 32V MINIMUM
VOLTAGE
n PROTECTION AGAINST SHORTED LOAD
10
AND OVERTEMPERATURE
n BUILT-IN CURRENT LIMITER n UNDER VOLTAGE SHUT DOWN n OPEN DRAIN DIAGNOSTIC OUTPUT n FAST DEMAGNETIZATION OF INDUCTIVE
1
PowerSO-10TM
LOADS
n CONFORMS TO IEC 1131-2
DESCRIPTION The VN340SP(8933) is a monolithic device made using STMicroelectronics VIPower technology, intended for driving four indipendent resistive or inductive loads with one side connected to ground. Active current limitation avoids dropping the system power supply in case of shorted load. BLOCK DIAGRAM
Built-in thermal shut down protects the chip from overtemperature and short circuit. The open drain diagnostic output indicates overtemperature conditions. Each I/O is pulled down when overtemperature condition of the relative channel is verified.
June 2001
1/10
1
VN340SP(8933)
ABSOLUTE MAXIMUM RATING
Symbol VCC -VCC IOUT IR IIN IDIAG VESD EAS PTOT Tj TSTG Parameter Power supply voltage Reverse supply voltage Output current (continuous) Reverse output current (per channel) Input current (per channel) Diag pin current Electrostatic discharge (R=1.5K; C=100pF) Single pulse avalanche energy per channel not simultaneously (see figure 1) Power dissipation at Tc=25C Junction operating temperature Storage temperature Value 45 -4 Internally limited -6 +/- 10 +/- 10 2000 400 Internally limited Internally limited -55 to 150 Unit V V A A mA mA V mJ W C C
CONNECTION DIAGRAM TOP VIEW
CURRENT AND VOLTAGE CONVENTIONS
2/10
1
VN340SP(8933)
THERMAL DATA
Symbol Rthj-case Rthj-amb Parameter Thermal resistance junction-case (1) Thermal resistance junction-ambient ($) (MAX) (MAX) Value 2 50 Unit C/W C/W
(1) All channels on ($) When mounted using minimum recommended pad size on FR-4 board
ELECTRICAL CHARACTERISTICS (10VSymbol VCC RON Parameter Supply voltage On state resistance Test Conditions IOUT=0.5A; Tj=25C IOUT=0.5A; -25C10M Output voltrage at turn-off IOUT=0.5A, LLOAD=1mH VCC=VINn=VGND=VSTAT=18 to 30V Output current at turn-off Tamb=-25C to 85C (*) Min 10 Typ Max 36 0.2 0.32 0.4 1 6 1.5 VCC-65 VCC-55 VCC-45 2 Unit V mA mA V V mA
(*) see test configuration and application description
SWITCHING (VCC=24V)
Symbol td(on) tr td(off) tf Parameter Turn-on delay on output current Rise time of output current Turn-off delay on output current Fall time of output current Test Conditions IOUT=0.5A, Resistive Load Input rise time <0.1s, Tj=25C IOUT=0.5A, Resistive Load Input rise time <0.1s, Tj=25C IOUT=0.5A, Resistive Load Input rise time <0.1s, Tj=25C IOUT=0.5A, Resistive Load Input rise time <0.1s, Tj=25C Min Typ 52 94 34 8 Max 100 250 50 20 Unit S S S S
3/10
1
VN340SP(8933)
ELECTRICAL CHARACTERISTICS (continued) LOGIC INPUT (Per each channel)
Symbol VIL VIH VI(HYST) IIN VICL Parameter I/O Input low level voltage I/O Input high level voltage (see note 1) I/OInput hysteresis voltage I/O Input current VIN=30V I/O Input clamp voltage IIN=1mA (see note 1) IIN=-1mA Test Conditions Min Typ Max 2 Unit V V 0.5 25 32 36 -0.7 V A V V
3.5
Note 1 : The input voltage is internally clamped at 32V minimum , it is possible to connect the input pins to an higher voltage via an external resistor calculate to not exceed 10mA.
PROTECTION AND DIAGNOSTICS
Symbol VDIAG (*) VSCL(*) VUSD ILIM IOVPK IDIAGH ILOAD tSC TTSD TR Parameter Status voltage output low Status clamp voltage Under voltage shut down DC Short circuit current Peak short circuit current Leakage on diag pin in high state Output leakage current Delay time of current limiter Thermal shut down temperature Thermal reset temperature Test Conditions ISTAT=5mA (Fault condition) IDIAG=1mA IDIAG=-1mA VCC=24V; RLOAD<10m VCC=24V; VIN=30V; RLOAD<10m (see figure 2) VDIAG=24V VCC=10 to 36V; VIN=VIL 5 1 Min Typ Max 1 32 36 0.7 8 2 4 25 50 100 150 135 170 155 Unit V V V V A A A A s
oC oC
(*) Status determination > 100ms after the switching edge. Note: If INPUT pin is floating the corrisponding channel will automatically switch off. If GND pin is disconnected, the channel will switch off provided VCC not exceed 36V.
4/10
2
VN340SP(8933)
FIGURE 1: Avalanche Energy Test Circuit
FIGURE 2: Peak Short Circuit Current Test Circuit
5/10
1
VN340SP(8933)
THRUTH TABLE
MCOUTn Normal operation Overtemperature Undervoltage Shorted load (Current limitation) L H L H L H L H I/On L H L L L H L H OUTPUTn L H L L L L L H DIAGNOSTIC H H H L H H H H
Figure 3: Switching Waveforms
6/10
1
VN340SP(8933)
SWITCHING PARAMETERS TEST CONDITIONS
DRIVING CIRCUIT
Fig. 4: ILGND Test Configuration
+
VCC
DIAG
OUTn I/On
GND
A
Ignd
FC12550
7/10
2
VN340SP(8933)
PowerSO-10TM MECHANICAL DATA
DIM. A A (*) A1 B B (*) C C (*) D D1 E E2 E2 (*) E4 E4 (*) e F F (*) H H (*) h L L (*) (*)
(*) Muar only POA P013P
mm. MIN. 3.35 3.4 0.00 0.40 0.37 0.35 0.23 9.40 7.40 9.30 7.20 7.30 5.90 5.90 1.27 1.25 1.20 13.80 13.85 0.50 1.20 0.80 0 2 1.80 1.10 8 8 0.047 0.031 0 2 1.35 1.40 14.40 14.35 0.049 0.047 0.543 0.545 TYP MAX. 3.65 3.6 0.10 0.60 0.53 0.55 0.32 9.60 7.60 9.50 7.60 7.50 6.10 6.30 MIN. 0.132 0.134 0.000 0.016 0.014 0.013 0.009 0.370 0.291 0.366 0.283 0.287 0.232 0.232
inch TYP. MAX. 0.144 0.142 0.004 0.024 0.021 0.022 0.0126 0.378 0.300 0.374 300 0.295 0.240 0.248 0.050 0.053 0.055 0.567 0.565 0.002 0.070 0.043 8 8
B
0.10 A B
10
H
E
E2
E4
1
SEATING PLANE e
0.25
B
DETAIL "A"
A
C D = D1 = = = SEATING PLANE
h
A F A1
A1
L DETAIL "A"
P095A
8/10
VN340SP(8933)
PowerSO-10TM SUGGESTED PAD LAYOUT
14.6 - 14.9
B
TUBE SHIPMENT (no suffix)
CASABLANCA MUAR
C
10.8- 11 6.30
A A
C
0.67 - 0.73 1 2 3 4 5 10 9 8 7 6 1.27 0.54 - 0.6
B
9.5
All dimensions are in mm. Base Q.ty Bulk Q.ty Tube length ( 0.5) Casablanca Muar 50 50 1000 1000 532 532 A B C ( 0.1) 0.8 0.8
10.4 16.4 4.9 17.2
TAPE AND REEL SHIPMENT (suffix "13TR")
REEL DIMENSIONS
Base Q.ty Bulk Q.ty A (max) B (min) C ( 0.2) F G (+ 2 / -0) N (min) T (max) 600 600 330 1.5 13 20.2 24.4 60 30.4
All dimensions are in mm.
TAPE DIMENSIONS
According to Electronic Industries Association (EIA) Standard 481 rev. A, Feb. 1986 Tape width Tape Hole Spacing Component Spacing Hole Diameter Hole Diameter Hole Position Compartment Depth Hole Spacing W P0 ( 0.1) P D ( 0.1/-0) D1 (min) F ( 0.05) K (max) P1 ( 0.1) 24 4 24 1.5 1.5 11.5 6.5 2
End
All dimensions are in mm.
Start Top cover tape 500mm min Empty components pockets saled with cover tape. User direction of feed 500mm min No components Components No components
9/10
1
VN340SP(8933)
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics (c) 2001 STMicroelectronics - Printed in ITALY- All Rights Reserved. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com
10/10
1

▲Up To Search▲

Price & Availability of 9609

	To Download 9609 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .