View 1460S35F_962893.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LT1460S3-5 (SOT-23) Micropower Series Reference in SOT-23
FEATURES
s s s s s s s s
DESCRIPTION
The LT (R)1460S3-5 is a SOT-23 micropower series reference that combines high accuracy and low drift with low power dissipation and small package size. This series reference uses curvature compensation to obtain low temperature coefficient, and laser trimmed precision thin-film resistors to achieve high output accuracy. Furthermore, output shift due to PC board soldering stress has been dramatically reduced. The reference will supply up to 20mA, making it ideal for precision regulator applications, yet it is almost totally immune to input voltage variations. This series reference provides supply current and power dissipation advantages over shunt references that must idle the entire load current to operate. Additionally, the LT1460S3-5 does not require an output compensation capacitor, but is stable with any capacitive load. This feature is important in critical applications where PC board space is a premium or fast settling is demanded. Reverse-battery protection keeps the reference from conducting current. For even tighter tolerance and lower temperature coefficient, the LT1460 is also available in the 8-lead MSOP, SO, PDIP and the 3-lead TO-92 packages. A 2.5V version is also available.
, LTC and LT are registered trademarks of Linear Technology Corporation.
3-Lead SOT-23 Package Low Drift: 20ppm/C Max High Accuracy: 0.2% Max Low Supply Current: 180A Max 20mA Output Current Guaranteed Stable with Any Capacitive Load Reverse-Battery Protection Low PC Board Solder Stress: 0.02% Typ
APPLICATIONS
s s s s s
Handheld Instruments Precision Regulators A/D and D/A Converters Power Supplies Hard Disk Drives
TYPICAL APPLICATION
Basic Connection
Typical Distribution of SOT-23 LT1460HC VOUT After IR Reflow Solder per JEDEC JESD22-A112
48 44 40 36
DISTRIBUTION (%)
5.9V TO 20V C1 0.1F
LT1460S3-5 IN GND
1460S3-5 TA01
OUT
5V
32 28 24 20 16 12 8 4 0 4.98 5.0 OUTPUT VOLTAGE (V) 5.02
1460S3-5 TA02
U
U
U
LT1460HC LIMITS
1
LT1460S3-5 (SOT-23)
ABSOLUTE MAXIMUM RATINGS
Input Voltage ........................................................... 30V Reverse Voltage .................................................... - 15V Output Short-Circuit Duration, TA = 25C VIN > 10V ........................................................... 5 sec VIN 10V ................................................... Indefinite Specified Temperature Range ..................... 0C to 70C Storage Temperature Range (Note 1) ... - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C
PACKAGE/ORDER INFORMATION
ORDER PART NUMBER
TOP VIEW IN 1 3 GND OUT 2 S3 PACKAGE 3-LEAD PLASTIC SOT-23
TJMAX = 125C, JA = 325C/ W
LT1460HCS3-5 LT1460JCS3-5 LT1460KCS3-5 S3 PART MARKING LTAK LTAL LTAM
Consult factory for Industrial and Military grade parts.
ELECTRICAL CHARACTERISTICS
PARAMETER Output Voltage (Note 2)
VIN = VOUT + 2.5V, IOUT = 0, TA = 25C unless otherwise specified.
MIN 4.990 - 0.2 4.980 - 0.4 4.975 - 0.5
q q q q
CONDITIONS LT1460HCS3 LT1460JCS3 LT1460KCS3
TYP 5.00 5.00 5.00
MAX 5.010 0.2 5.020 0.4 5.025 0.5 20 20 50 800 1000 100 130 6000 8000 400 500 300 380 10 0.9 1.3 1.4
UNITS V % V % V % ppm/C ppm/C ppm/C ppm/V ppm/V ppm/V ppm/V ppm/mA ppm/mA ppm/mA ppm/mA ppm/mA ppm/mA ppm/mW V V V mA A
Output Voltage Temperature Coefficient (Note 3)
TMIN TJ TMAX LT1460HCS3 LT1460JCS3 LT1460KCS3 5.9V VIN 7.5V 7.5V VIN 20V
10 10 25 150 50
Line Regulation
q
Load Regulation Sourcing (Note 4)
IOUT = 100A
q
4300 280
q
IOUT = 10mA IOUT = 20mA 0C TA 70C Thermal Regulation (Note 5) Dropout Voltage (Note 6) P = 200mW VIN - VOUT, VOUT 0.2%, IOUT = 0 VIN - VOUT, VOUT 0.2%, IOUT = 10mA
q q
220
q
2.5
Output Current Reverse Leakage
Short VOUT to GND VIN = - 15V
q
40 0.5 10
2
U
W
U
U
WW
W
LT1460S3-5 (SOT-23)
ELECTRICAL CHARACTERISTICS
PARAMETER Supply Current
VIN = VOUT + 2.5V, IOUT = 0, TA = 25C unless otherwise specified.
MIN
q
CONDITIONS
TYP 125
MAX 180 225
UNITS A A VP-P VRMS ppm/kHr ppm
Output Voltage Noise (Note 7) Long-Term Stability of Output Voltage (Note 8) Hysteresis (Note 9)
0.1Hz f 10Hz 10Hz f 1kHz T = 0C to 70C
20 20 70 100
The q denotes specifications which apply over the full specified temperature range. Note 1: If the part is stored outside of the specified temperature range, the output may shift due to hysteresis. Note 2: ESD (Electrostatic Discharge) sensitive device. Extensive use of ESD protection devices are used internal to the LT1460S3-5, however, high electrostatic discharge can damage or degrade the device. Use proper ESD handling precautions. Note 3: Temperature coefficient is measured by dividing the change in output voltage by the specified temperature range. Incremental slope is also measured at 25C. Note 4: Load regulation is measured on a pulse basis from no load to the specified load current. Output changes due to die temperature change must be taken into account separately. Note 5: Thermal regulation is caused by die temperature gradients created by load current or input voltage changes. This effect must be added to normal line or load regulation. This parameter is not 100% tested. Note 6: Excludes load regulation errors. Note 7: Peak-to-peak noise is measured with a single highpass filter at 0.1Hz and 2-pole lowpass filter at 10Hz. The unit is enclosed in a still-air environment to eliminate thermocouple effects on the leads. The test time
is 10 sec. RMS noise is measured with a single highpass filter at 10Hz and a 2-pole lowpass filter at 1kHz. The resulting output is full wave rectified and then integrated for a fixed period, making the final reading an average as opposed to RMS. A correction factor of 1.1 is used to convert from average to RMS and a second correction of 0.88 is used to correct for the nonideal bandpass of the filters. Note 8: Long-term stability typically has a logarithmic characteristic and therefore, changes after 1000 hours tend to be much smaller than before that time. Total drift in the second thousand hours is normally less than one third that of the first thousand hours with a continuing trend toward reduced drift with time. Significant improvement in long-term drift can be realized by preconditioning the IC with a 100 hour to 200 hour, 125C burn-in. Long-term stability will also be affected by differential stresses between the IC and the board material created during board assembly. Note 9: Hysteresis in output voltage is created by package stress that differs depending on whether the IC was previously at a higher or lower temperature. Output voltage is always measured at 25C, but the IC is cycled to 70C or 0C before successive measurements. Hysteresis is roughly proportional to the square of the temperature change. Hysteresis is not normally a problem for operational temperature excursions where the instrument might be stored at high or low temperature.
TYPICAL PERFORMANCE CHARACTERISTICS
Minimum Input-Output Voltage Differential
100 20 18
OUTPUT VOLTAGE CHANGE (mV)
OUTPUT VOLTAGE CHANGE (mV)
OUTPUT CURRENT (mA)
10
25C
1
125C
- 55C
0.1 0 0.5 1.0 1.5 2.0 INPUT-OUTPUT VOLTAGE (V) 2.5
1460-5 G01
UW
Load Regulation, Sourcing
125C 60 50 40
Load Regulation, Sinking
16 14 12 10 8 6 4 2 0 0.1 - 55C 25C
125C 30 25C 20 10 0 - 55C
1 10 OUTPUT CURRENT (mA)
100
1460S3-5 G02
0
0.25 0.50 0.75 OUTPUT CURRENT (mA)
1.0
1460S3-5 G03
3
LT1460S3-5 (SOT-23) TYPICAL PERFORMANCE CHARACTERISTICS
Output Voltage Temperature Drift
5.015 5.010 3 TYPICAL PARTS
SUPPLY CURRENT (A)
OUTPUT VOLTAGE (V)
125C 200 25C 150 - 55C 100 50 0
5.000 4.995 4.990 4.985 4.980 4.975 - 50 - 25 0 50 25 TEMPERATURE (C) 75 100
OUTPUT VOLTAGE (V)
5.005
Power Supply Rejection Ratio vs Frequency
100
POWER SUPPLY REJECTION RATIO (dB)
90 80 70 60 50 40 30 20 10 0 0.1 1 10 100 FREQUENCY (kHz) 1000
1460S3-5 G07
OUTPUT IMPEDANCE ()
CL = 0F 100 CL = 0.1F
LOAD CAPACITANCE (F)
Typical Long-Term Drift
80 60
OUTPUT VOLTAGE (ppm)
40 20 0 - 20 - 40 - 60 - 80
1000
100
OUTPUT NOISE (10V/DIV)
NOISE VOLTAGE (nV/Hz)
0
200
400
600
TIME (HOURS)
1460S3-5 G10
4
UW
800
Supply Current vs Input Voltage
300 250
Line Regulation
5.006 125C 5.002 25C 4.998
4.994
4.990 - 55C
0 5 10 15 INPUT VOLTAGE (V) 20
1460S3-5 G05
4.986
0
2
4
6 8 10 12 14 16 18 20 INPUT VOLTAGE (V)
1460S3-5 G06
1460S3-5 G04
Output Impedance vs Frequency
1000
Transient Response
10
1
0.1
10 CL = 1F
0 200s/DIV IOUT = 10mA
1460S3-5 G09
1 0.01
0.1
1 10 FREQUENCY (kHz)
100
1000
1460S3-5 G08
Output Voltage Noise Spectrum
3000 2000
Output Noise 0.1Hz to 10Hz
1000
10
100
1k 10k FREQUENCY (Hz)
100k
1460S3-5 G11
0
1
2
3
456 TIME (SEC)
7
8
9
10
1460S3-5 G12
LT1460S3-5 (SOT-23)
APPLICATIONS INFORMATION
Longer Battery Life Series references have a large advantage over older shunt style references. Shunt references require a resistor from the power supply to operate. This resistor must be chosen to supply the maximum current that can ever be demanded by the circuit being regulated. When the circuit being controlled is not operating at this maximum current, the shunt reference must always sink this current, resulting in high dissipation and short battery life. The LT1460S3-5 series reference does not require a current setting resistor and can operate with any supply voltage from VOUT + 0.9V to 20V. When the circuitry being regulated does not demand current, the LT1460S3-5 reduces its dissipation and battery life is extended. If the reference is not delivering load current it dissipates less than 1mW on a 7.5V supply, yet the same connection can deliver 20mA of load current when demanded. Capacitive Loads The LT1460S3-5 is designed to be stable with any capacitive load. With no capacitive load, the reference is ideal for fast settling or applications where PC board space is a premium. The test circuit shown in Figure 1 is used to measure the response time for various load currents and load capacitors. The 1V step from 5V to 4V produces a current step of 1mA or 100A for RL = 1k or RL = 10k. Figure 2 shows the response of the reference with no load capacitance. The reference settles to 10mV (0.2%) in 1.2s for a 100A pulse and to 0.2% in 1.8s with a 1mA step. Figure 3 shows the response of the reference to a 1mA and 100A load with a 0.01F load capacitor. Figure 4 shows the response with a 1F and 10F load capacitance.
RL VGEN CL 5V 4V
1460S3-5 F01
VIN = 7.5V CIN 0.1F
LT1460S3-5
VOUT
Figure 1. Response Time Test Circuit
U
W
U
U
5V VGEN 4V
VOUT
RL = 10k
VOUT
RL = 1k
1s/DIV
1460S3-5 F02
Figure 2. CL = 0F
5V VGEN 4V
VOUT
RL = 10k
VOUT
RL = 1k
20s/DIV
1460S3-5 F03
Figure 3. CL = 0.01F
5V VGEN 4V
VOUT
CL = 1F
VOUT
CL = 10F
200s/DIV
1460S3-5 F04
Figure 4. IOUT = 1mA
5
LT1460S3-5 (SOT-23)
APPLICATIONS INFORMATION
Fast Turn-On It is recommended to add a 0.1F or larger bypass capacitor to the input pin of the LT1460S3-5. Although this can help stability with large load currents, the main reason is for proper start-up. The LT1460S3-5 can start in 10s, but it is important to limit the dv/dt of the input. Under light load conditions and with a very fast input, internal nodes overslew and this requires finite recovery time. Figure 5 shows the result of no bypass capacitance on the input and no output load. In this case the supply dv/dt is 7.5V in 30ns which causes internal overslew, and the output does not bias to 5V until 40s. Although 40s is a typical turn-on time, it can be much longer. Figure 6 shows the effect of a 0.1F bypass capacitor which limits the input dv/dt to approximately 7.5V in 20s and the part always starts quickly. Output Accuracy Like all references, either series or shunt, the error budget of the LT1460S3-5 is made up of primarily three components: initial accuracy, temperature coefficient and load regulation. Line regulation is neglected because it typically contributes only 150ppm/V, or 750V for a 1V input change. The LT1460S3-5 typically shifts 0.02% when soldered into a PCB, so this is also neglected. The output errors are calculated as follows for a 100A load and 0C to 70C temperature range: LT1460HCS3 Initial Accuracy = 0.2% For IOUT = 100A VOUT = (8000ppm/mA)(0.1mA)(2.5V) = 2.0mV which is 0.08% For Temperature 0C to 70C the maximum T = 70C VOUT = (20ppm/C)(70C)(2.5V) = 3.5mV which is 0.14% Total worst-case output error is: 0.2% + 0.08% + 0.14% = 0.420% Table 1 gives the worst-case accuracy for LT1460HCS3, LT1460JCS3 and LT1460KCS3 from 0C to 70C, and shows that if the LT1460HCS3 is used as a reference instead of a regulator, it is capable of 8 bits of absolute accuracy over temperature without a system calibration.
Table 1. Worst-Case Output Accuracy over Temperature
IOUT 0A 100A 10mA 20mA LT1460HCS3 0.340% 0.420% 0.840% 1.100% LT1460JCS3 0.540% 0.620% 1.040% 1.300% LT1460KCS3 0.850% 0.930% 1.350% 1.610%
VIN 0V
VOUT 0V 20s/DIV
1460S3-5 F05
Figure 5. CIN = 0F
6
U
W
U
U
7.5V VIN
7.5V 0V
VOUT
20s/DIV
1460S3-5 F06
Figure 6. CIN = 0.1F
LT1460S3-5 (SOT-23)
PACKAGE DESCRIPTION
REF
0.55 (0.022)
NOTE: GOVERNING DIMENSION IN MILLIMETERS DIMENSIONS ARE INCLUSIVE OF PLATING DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR MOLD FLASH SHALL NOT EXCEED 0.254mm JEDEC REFERENCE NUMBER IS T0-236 VARIATION AB
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
Dimensions in millimeters (inches) unless otherwise noted.
S3 Package 3-Lead Plastic SOT-23
(LTC DWG # 05-08-1631)
2.80 - 3.04 (0.110 - 0.120)
2.10 - 2.64 (0.083 - 0.104) 1.20 - 1.40 (0.047 - 0.060)
0.45 - 0.60 (0.017 - 0.024)
0.89 - 1.03 (0.035 - 0.041) 1.78 - 2.05 (0.070 - 0.081) 0.89 - 1.12 (0.035 - 0.044)
0.01 - 0.10 (0.0004 - 0.004)
0.09 - 0.18 (0.004 - 0.007)
0.37 - 0.51 (0.015 - 0.020)
SOT-23 0897
7
LT1460S3-5 (SOT-23)
TYPICAL APPLICATIONS
Handling Higher Load Currents
7.5V 40mA
Boosted Output Current with No Current Limit
V + (VOUT + 1.8V) R1 220 2N2905 IN LT1460S3-5 OUT GND 5V 100mA 2F SOLID TANT
+
RELATED PARTS
PART NUMBER LT1019 LT1027 LT1236 LT1634 DESCRIPTION Precision Bandgap Reference Precision 5V Reference Precision Low Noise Reference Micropower Precision Shunt Reference 1.25V, 2.5V Output COMMENTS 0.05% Max, 5ppm/C Max 0.02%, 2ppm/C Max 0.05% Max, 5ppm/C Max, SO Package 0.05%, 25ppm/C Max
8
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417 q (408) 432-1900 FAX: (408) 434-0507 q TELEX: 499-3977 q www.linear-tech.com
U
+
47F
IN LT1460S3-5 OUT GND 10mA
R1* 63 VOUT 5V RL TYPICAL LOAD CURRENT = 50mA
*SELECT R1 TO DELIVER 80% OF TYPICAL LOAD CURRENT. LT1460 WILL THEN SOURCE AS NECESSARY TO MAINTAIN PROPER OUTPUT. DO NOT REMOVE LOAD AS OUTPUT WILL BE DRIVEN UNREGULATED HIGH. LINE REGULATION IS DEGRADED IN THIS APPLICATION
1460S3-5 TA05
Boosted Output Current with Current Limit
V+ VOUT + 2.8V
+
47F
D1* LED
R1 220
+
8.2 2N2905 47F
IN LT1460S3-5 OUT GND 5V 100mA 2F SOLID TANT
1460S3-5 TA04
+
1460S3-5 TA03
* GLOWS IN CURRENT LIMIT, DO NOT OMIT
1460S35F LT/TP 1097 4K * PRINTED IN USA
(c) LINEAR TECHNOLOGY CORPORATION 1997

▲Up To Search▲

Price & Availability of 1460S35F

	To Download 1460S35F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .