View 0408_961608.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ICs for Compact Disc/CD-ROM Player
AN8746SA
PWM driver IC for portable CD player
s Overview
The AN8746SA is a 4-channel actuator/motor drive IC by DMOS direct PWM method for a portable CD player.
11.00.3 32 17
Unit: mm
s Features
* RON = 1.8 (typ.) * Supply voltage range (Control block: 2.0 V to 3.6 V, power block: 1.2 V to 3.6 V) * Current at standby (Control block: 1 A or less, power block: 1 A or less) * With an output pin of monitoring 1/2 of the power supply voltage
0.650.10
1.50.2
1
16
6.10.3
8.10.3
(0.5)
0.2+0.10 -0.05
(0.625)
0.65
0.3 -0.05
Seating plane
SSOP032-P-0300
s Applications
* Portable CD player
s Block Diagram
PGND4 PGND3
0.10.1
+0.10
0.650.10
VGO 18 15 N.C.
VM4
32
31
30
29
28
27
26
25
24
23
22
21
20
19
Logic circuit Reset TSD Predriver H bridge H bridge
Logic circuit Predriver VG limiter
VBG
Predriver
VM1 monitor Logic circuit
H bridge
H bridge
Predriver Logic circuit
10
11
12
13
14
MON
Fi1
Ri1
Ro1
PGND1
Fo1
Fo2
PGND2
Ro2
Ri2
Fi2
GND
VM1
VC
VM2
16
1
2
3
4
5
6
7
8
9
17
VM3
Ro4
Ro3
VGI
Fo4
Fo3
Ri4
Ri3
AC
Fi4
Fi3
PC
1
AN8746SA
s Pin Descriptions
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Symbol VM1 VC MON Fil Ril Rol PGND1 Fo1 Fo2 PGND2 Ro2 Ri2 Fi2 GND N.C. VM2 Description Ch. 1 power supply Control circuit power supply VM1 monitor Ch. 1 forward direction input pin Ch. 1 reverse direction input pin Ch. 1 reverse direction output pin Ch. 1 power ground Ch. 1 forward direction output pin Ch. 2 forward direction output pin Ch. 2 power ground Ch. 2 reverse direction output pin Ch. 2 reverse direction intput pin Ch. 2 forward direction input pin Control circuit ground Ch. 2 power supply
ICs for Compact Disc/CD-ROM Player
Pin No. 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Symbol VM3 VGO VGI Fi3 Ri3 Ro3 PGND3 Fo3 Fo4 PGND4 Ro4 Ri4 Fi4 PC AC VM4
Description Ch.3 power supply Gate voltage clamp output Gate voltage input pin Ch. 3 forward direction input pin Ch. 3 reverse direction input pin Ch. 3 reverse direction output pin Ch. 3 power ground Ch. 3 forward direction output pin Ch. 4 forward direction output pin Ch. 4 power ground Ch. 4 reverse direction output pin Ch. 4 reverse direction input pin Ch. 4 forward direction input pin Power cut pin All cut-off pin Ch. 4 power supply
s Absolute Maximum Ratings
Parameter Supply voltage Symbol VC VM VGI Supply current Power dissipation
*2 *1
Rating 5 7 8.2 500 400 -30 to +75 -55 to +150
Unit V
IDD PD Topr Tstg
*1
mA mW C C
Operating ambient temperature Storage temperature
Note) *1: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25C. *2: Use within the range of PD = 390 mW or less at Ta = 75C, following the allowable power dissipation characteristic curve of "s Application Notes".
s Recommended Operating Range
Parameter Supply voltage Symbol VC VM VGI Signal input voltage VIN Range 2.0 to 2.4 to 3.6 1.2 to 2.4 to 3.6 VM +3.5 to 7.0 to 8.0 0 to VC V Unit V
2
ICs for Compact Disc/CD-ROM Player
AN8746SA
s Electrical Characteristics at VC = 2.4 V, VM12 = VM34 = 2.4 V, VGI = 7.0 V, AC = PC = 2.4 V, RL = 8 , Ta = 25C
Parameter Power supply current at mute (at PC = L or VC = L) *1 Control supply current at all cut (at AC = L or PC = L) Control supply current at operating *2 Pre-driver supply current at all cut (at AC = L) *2 Pre-driver supply current at operation (at VGI = 7 V) *2 PWM input voltage high-level PWM input voltage low-level PWM input current high-level PWM input current low-level Driver on resistance (upper and lower) Output propagation delay time at rising *2 Output propagation delay time at falling *2 Output propagation delay time difference tDr-tDf Minimum input pulse width *3 VM monitor output voltage width VM monitor output gain Power output pin flow-out/in current at low VC *1 VM monitor output voltage at VC limit Symbol IMO ICO IC IGO IG VINH VINL IINH IINL RON tDr tDf tD tmin VMON GMON IHZ Conditions PC = 0 V, AC = VC = 2.4 V or VC = PC = AC = 0 V AC = L, PC = L AC = PC = VC = 2.4 V AC = 0 V AC = PC = VC = 2.4 V AC = PC = VC = 2.4 V Fil to Fi4 = Ril to Ri4 = H AC = PC = VC = 2.4 V Fil to Fi4 = Ril to Ri4 = L AC = PC = VC = 2.4 V Fil to Fi4 = Ril to Ri4 = H AC = PC = VC = 2.4 V Fil to Fi4 = Ril to Ri4 = L AC = PC = VC = 2.4 V AC = PC = VC = 2.4 V AC = PC = VC = 2.4 V AC = PC = VC = 2.4 V AC = PC = VC = 2.4 V AC = PC = VC = 2.4 V AC = PC = VC = 2.4 V AC = PC = VC = 0 V Min VC - 0.6 -1 - 0.3 0.3 1.1 0.45 -50 1.7 Typ 0.5 0.5 1.8 0.2 0.2 1.2 0.5 1.9 Max 1 1 1 1 1 0.6 1 2.5 1 1 0.3 1.3 0.55 50 2.1 Unit A A mA A mA V V A A s s s s V A V
LMON VM12 = VM34 = 5.0 V AC = PC = VC = 1.9 V
Note) *1: AC pin and PC pin are connected to VC pin via a protective diode. AC pin and PC pin must be set to 0 V at VC = 0 V to avoid excessive flow-in current. 2: Measure at f = 44.1 kHz and in duty ratio = 50%. * *3: Measure at f = 44.1 kHz. Output pulse width must be tmin /2.
3
AN8746SA
ICs for Compact Disc/CD-ROM Player
s Electrical Characteristics at VC = 2.4 V, VM12 = VM34 = 2.4 V, VGI = 7.0 V, AC = PC = 2.4 V, RL = 8 , Ta = 25C (continued)
* Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Thermal protection Thermal protection operating temperature Thermal protection hysteresis width
Symbol
Conditions
Min
Typ
Max
Unit C C
TTHD TTHD
145 20
s Usage Notes
1. Care should be taken so as not to cause any of the following conditions on use of this IC. If the following conditions come up, the IC is likely to break down or to be smoking. Short-circuit between output pins Short-circuit between output pin and GND Short-circuit between output pin and power supply (Output pin refers to any of those Fo1 (pin 8), Ro1 (pin 6), Fo2 (pin 9), Ro2 (pin 11), Fo3 (pin 24), Ro3 (pin 22), Fo4 (pin 25), Ro4 (pin 27). GND refers to any of those GND (pin 14), PGND1 (pin 7), PGND2 (pin 10), PGND3 (pin 23), PGND4 (pin 26). Power supply refers to any of those VC (pin 2), VGI (pin 19), VM1 (pin 1), VM2 (pin16), VM3 (pin 17), VM4 (pin 32). 2. VM1 monitor pin (pin 3) outputs approximately one half of VM1 voltage and its upper limit is VC supply voltage. This is meant to prevent the DSP connected to this Pin from damage when the voltage exceeding an operating supply voltage range is inputted to the VM1 pin. On use of this pin, therefore, note that no value exceeding VC is outputted.
s Application Notes
1. PD Ta curves of SSOP032-P-0300 PD T a
1.400 1.288 1.200 Mounted on standard board (glass epoxy: 50 mm x 50 mm x t0.8 mm) Rth(j-a) = 97.0C/W
Power dissipation PD (W)
1.000
0.800
0.667 0.600 Independent IC without a heat sink Rth(j-a) = 187.2C/W
0.400
0.200
0.000 0
25
50
75
100
125
150
Ambient temperature Ta (C)
4
ICs for Compact Disc/CD-ROM Player
s Application Notes
2. Logic table of driver VC H H H H H L PC H H H H L X Fil to Fi4 L L H H X X Ril to Ri4 L H L H X X Fol to Fo3 L L H L L Hi-Z Rol to Ro3 L H L L L Hi-Z
AN8746SA
Fo4 L L L H L Hi-Z
Ro4 L H L L L Hi-Z
Note) AC = H on the above logic table. H stands for VC power supply potential, L for GND potential (0 V) and X for H or L. Hi-Z indicates that the driver output pin becomes a high impedance state. Logic input pin must not be left open. And do not apply any other voltages than H or L.
s Application Circuit Example
DSP Microcomputer
M M
VGI = 7 V
26 PGND4
23 PGND3
18 VGO 15 N.C.
32 VM4
Logic circuit Reset TSD Predriver H bridge H bridge
Logic circuit Predriver VG limiter
VBG
Predriver
VM1 monitor Logic circuit
H bridge
H bridge
Predriver Logic circuit
PGND2 10
Ro2 11
Ri2 12
Fi2 13
GND 14
VM1 1
MON 3
PGND1 7
DSP VC = 2.4 V/0 V VM = 2.4 V
VM2 16
5
VC 2
Fi1 4
Ri1 5
Ro1 6
Fo1 8
Fo2 9
17 VM3
27 Ro4
22 Ro3
19 VGI
25 Fo4
24 Fo3
28 Ri4
21 Ri3
31 AC
29 Fi4
20 Fi3
30 PC
Request for your special attention and precautions in using the technical information and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (4) The products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) When using products for which dry packing is required, observe the conditions (including shelf life and after-unpacking standby time) agreed upon when specification sheets are individually exchanged. (7) No part of this material may be reprinted or reproduced by any means without written permission from our company.
Please read the following notes before using the datasheets
A. These materials are intended as a reference to assist customers with the selection of Panasonic semiconductor products best suited to their applications. Due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. Customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. Therefore, Panasonic will not assume any liability for any damages arising from any errors etc. that may appear in this material. C. These materials are solely intended for a customer's individual use. Therefore, without the prior written approval of Panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.
2001 MAR

▲Up To Search▲

Price & Availability of 0408

	To Download 0408 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .