|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
LM2575 Micrel LM2575 52kHz Simple 1A Buck Regulator Final Information General Description The LM2575 series of monolithic integrated circuits provide all the active functions for a step-down (buck) switching regulator. Fixed versions are available with a 3.3V, 5V, 12V, fixed output. Adjustable versions have an output voltage range from 1.23V to 37V. Both versions are capable of driving a 1A load with excellent line and load regulation. These regulators are simple to use because they require a minimum number of external components and include internal frequency compensation and a fixed-frequency oscillator. The LM2575 series offers a high efficiency replacement for popular three-terminal adjustable linear regulators. It substantially reduces the size of the heat sink, and in many cases no heat sink is required. A standard series of inductors available from several different manufacturers are ideal for use with the LM2575 series. This feature greatly simplifies the design of switch-mode power supplies. The feedback voltage is guaranteed to 2% tolerance for adjustable versions, and the output voltage is guaranteed to 3% for fixed versions, within specified input voltages and output load conditions. The oscillator frequency is guaranteed to 10%. External shutdown is included, featuring less than 200A standby current. The output switch includes cycle-bycycle current limiting and thermal shutdown for full protection under fault conditions. Features * 3.3V, 5V, 12V, and adjustable output versions * Voltage over specified line and load conditions: Fixed version: 3% max. output voltage Adjustable version: 2% max. feedback voltage * Guaranteed 1A output current * Wide input voltage range: 4V to 40V * Wide output voltage range 1.23V to 37V * Requires only 4 external components * 52kHz fixed frequency internal oscillator * Low power standby mode IQ typically < 200A * 80% efficiency (adjustable version typically > 80%) * Uses readily available standard inductors * Thermal shutdown and current limit protection * 100% electrical thermal limit burn-in Applications * * * * * Simple high-efficiency step-down (buck) regulator Efficient pre-regulator for linear regulators On-card switching regulators Positive to negative converter (inverting Buck-Boost) Isolated Flyback Converter using minimum number of external components * Negative Boost Converter Typical Applications 870 20 7V-40V Unregulated DC Input 1 4 LM2575-5.0 Feedback +VIN + CIN 100F 3 5 Gnd On/Off Output L1 2 330H D1 1N5822 +5V, 1A Regulated Output + COUT 330F 7V-40V Unregulated DC Input 1 4 LM2575 Feedback +VIN + CIN 100F 3 5 Gnd On/Off Output L1 2 330H D1 1N5822 +5V, 1A Regulated Output + COUT 330F R2 3.09k R1 1k Note: Pin numbers are for TO-220 Package Note: Pin numbers are for TO-220 Package R2 VOUT = 1.23 1 + R1 ( ) Fixed Regulator in Typical Application Adjustable Regulator in Fixed Output Application Micrel, Inc. * 1849 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 944-0970 * http://www.micrel.com August 1999 1 M2575 LM2575 Micrel Ordering Information Part Number LM2575BN* LM2575-3.3BN LM2575-5.0BN LM2575-12BN LM2575BWM* LM2575-3.3BWM LM2575-5.0BWM LM2575-12BWM LM2575BT* Temperature Range -40C to +85 C -40C to +85 C -40C to +85 C -40C to +85 C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package 16-pin Plastic DIP 16-pin Plastic DIP 16-pin Plastic DIP 16-pin Plastic DIP 24-pin Wide SOIC 24-pin Wide SOIC 24-pin Wide SOIC 24-pin Wide SOIC 5-lead TO-220 5-lead TO-220 5-lead TO-220 5-lead TO-220 5-lead TO-263 5-lead TO-263 5-lead TO-263 5-lead TO-263 LM2575-3.3BT LM2575-5.0BT LM2575-12BT LM2575BU* LM2575-3.3BU LM2575-5.0BU LM2575-12BU * Adjustable output regulators. Contact factory for bent or staggered leads option. Pin Configurations 5-LEAD TO-220 (T) GND 5- ON/OFF 4- FEEDBACK 3- GROUND 2- OUTPUT 1- VIN GND 5-LEAD TO-263 (U) 5- ON/OFF 4- FEEDBACK 3- GROUND 2- OUTPUT 1- VIN 24-LEAD SOIC (WM) 16-LEAD DIP (N) NC NC OUTPUT NC GND NC FB NC 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VIN NC GND GND GND GND NC ON/OFF PWR GND NC NC NC NC NC FB SIG GND NC ON/OFF NC PWR GND 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 NC NC NC NC NC NC OUTPUT OUTPUT NC VIN VIN NC LM2575 2 August 1999 LM2575 Micrel Absolute Maximum Ratings (Note 1) Maximum Supply Voltage ON/OFF Pin Input Voltage Output Voltage to Ground (Steady State) Power Dissipation Storage Temperature Range Minimum ESD Rating C = 100pF, R = 1.5k FB Pin Lead Temperature (soldering, 10 sec.) Maximum Junction Temperature 45V -0.3V V +40V -1V Internally Limited -65C to +150C 2 kV 1 kV 260C 150C Operating Ratings Temperature Range Supply Voltage -40C TJ +125C 40V Electrical Characteristics Specifications with standard typeface are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN = 12V, and ILOAD = 200mA. LM2575 Parameter Conditions Typ Limit (Note 2) Units (Limits) Symbol SYSTEM PARAMETERS, ADJUSTABLE REGULATORS (Note 3) Test Circuit Figure 1 VOUT Feedback Voltage VIN = 12V , ILOAD = 0.2A VOUT = 5V 0.2A ILOAD 1A, 8V VIN 40V VOUT = 5V VIN = 12V, ILOAD = 1A, VOUT = 5V VIN = 12V , ILOAD = 0.2A VOUT = 3.3V 0.2A ILOAD 1A, 8V VIN 40V VOUT = 3.3V VIN = 12V, ILOAD = 1A VIN = 12V , ILOAD = 0.2A VOUT = 5V 0.2A ILOAD 1A, 8V VIN 40V VOUT = 5V VIN = 12V, ILOAD = 1A VIN = 25V , ILOAD = 0.2A VOUT = 12V 0.2A ILOAD 1A, 15V VIN 40V VOUT = 12V VIN = 25V, ILOAD = 1A 1.230 1.217 1.243 1.230 1.193/1.180 1.267/1.280 82 V V(min) V(max) V V(min) V(max) % VOUT Feedback Voltage LM2575 Efficiency SYSTEM PARAMETERS, 3.3V REGULATORS (Note 3) Test Circuit Figure 1 VOUT Output Voltage 3.3 3.234 3.366 3.3 3.168/3.135 3.432/3.465 75 V V(min) V(max) V V(min) V(max) % VOUT Output Voltage LM2575-3.3 Efficiency SYSTEM PARAMETERS, 5V REGULATORS (Note 3) Test Circuit Figure 1 VOUT Output Voltage 5.0 4.900 5.100 5.0 4.800/4.750 5.200/5.250 82 V V(min) V(max) V V(min) V(max) % VOUT Output Voltage LM2575-5.0 Efficiency SYSTEM PARAMETERS, 12V REGULATORS (Note 3) Test Circuit Figure 1 VOUT Output Voltage 12 11.760 12.240 12 11.520/11.400 12.480/12.600 88 V V(min) V(max) V V(min) V(max) % VOUT Output Voltage LM2575-12 Efficiency August 1999 3 M2575 LM2575 Micrel Electrical Characteristics (continued) LM2575 Symbol Parameter Conditions Typ Limit (Note 2) Units (Limits) DEVICE PARAMETERS, ADJUSTABLE REGULATOR IB fO Feedback Bias Current VOUT = 5V 50 100/500 nA DEVICE PARAMETERS, FIXED and ADJUSTABLE REGULATORS Oscillator Frequency 52 47/42 58/63 Saturation Voltage Max Duty Cycle (ON) Current Limit IOUT = 1A (Note 4) (Note 5) Peak Current, tON 3s (Note 4) 0.9 1.2/1.4 98 93 ICL 2.2 1.7/1.3 3.0/3.2 2 7.5 30 5 10 Standby Quiescent Current Thermal Resistance ON/OFF Pin = 5V (OFF) T Package, Junction to Ambient (Note 7) T Package, Junction to Ambient (Note 8) T Package, Junction to Case N Package, Junction to Ambient (Note 9) WM Package, Junction to Amb. (Note 9) 50 200 65 45 2 85 100 kHz kHz (min) kHz (max) V V(max) % %(min) A A(min) A(max) mA(max) mA mA(max) mA mA(max) A A(max) C/W VSAT DC IL Output Leakage Current VIN = 40V, (Note 6), (Note 6) Output = 0V Output = -1V Output = -1V IQ ISTBY JA JA JC JA JA Quiescent Current (Note 6) LM2575 4 August 1999 LM2575 LM2575 Symbol Parameter Conditions Typ Limit (Note 2) Micrel Units (Limits) ON/OFF CONTROL, FIXED and ADJUSTABLE REGULATORS Test Circuit Figure 1 VIH VIL IIH IIL Note 1: ON/OFF Pin Logic Input Level ON /OFF Pin Logic Current VOUT = 0V VOUT = 5V ON /OFF Pin = 5V (OFF) ON/OFF Pin = 0V (ON) 1.4 1.2 4 2.2/2.4 1.0/0.8 30 V(min) V(max) A A(max) A A(max) 0.01 10 Absolute Maximum Rating indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face) . All room temperature limits are 100% production tested. All limits at temperature extreme are guaranteed via testing. External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the LM2575/LM1575 is used as shown in Figure 1 test circuit, system performance will be shown in system parameters section of Electrical Characteristics. Output (pin 2) sourcing current. No diode, inductor or capacitor connected to output. Feedback (pin 4) removed from output and connected to 0V. Feedback (pin 4) removed from output and connected to 12V to force the output transistor OFF. Junction to ambient thermal resistance (no external heat sink) for the 5-lead TO-220 package mounted vertically, with 1/2" leads in a socket, or on PC board with minimum copper area. Junction to ambient thermal resistance (no external heat sink) for the 5-lead TO-220 package mounted vertically, with 1/4" leads soldered to PC board containing approximately 4 square inches of copper area surrounding the leads. Junction to ambient thermal resistance with approximately 1 square inch of pc board copper surrounding the leads. Additional copper will lower thermal resistance further. Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: Note 8: Note 9: Typical Performance Characteristics Normalized Feedback Voltage* NORMALIZED FEEDBACK VOLTAGE (mV) Feedback Voltage vs Duty Cycle* 20 FEEDBACK VOLTAGE CHANGE (mV) 25 20 15 10 5 0 -5 -10 -15 -20 -25 -75 -50 -25 0 VIN = 12V ILOAD = 200mA Normalized to TJ = 25C 15 10 5 0 -5 -10 -15 -20 0 20 40 ILOAD = 200 mA VIN = 40V VIN = 7V 25 50 75 100 125 150 60 80 100 JUNCTION TEMPERATURE (C) DUTY CYCLE (%) * Adjustable version only August 1999 5 M2575 LM2575 Micrel (Circuit of Figure 1) Typical Performance Characteristics (continued) Supply Current vs. Duty Cycle Supply Current 20 18 SUPPLY CURRENT (mA) Standby Quiescent Current STANDBY QUIESCENT CURRENT (A) 16 14 12 10 8 6 4 0 10 20 30 SUPPLY CURRENT (mA) Measured at Ground Pin TJ = 25C VOUT = 5V 20.0 17.5 15.0 12.5 10.0 7.5 5.0 2.5 VIN from 7V to 40V 0 20 40 60 80 100 ILOAD = 200 mA 200 VIN = 40V 150 VON/OFF = 5V VIN = 12V 50 100 ILOAD to 1A 40 50 60 0 0 -75 -50 -25 0 25 50 75 100 125 150 JUNCTION TEMPERATURE (C) INPUT VOLTAGE (V) DUTY CYCLE (%) Current Limit 3 VI N = 25V SATURATION VOLTAGE (V) OUTPUT CURRENT (A) Switch Saturation Voltage 1.2 100 95 1.0 -55C -40C 0.8 25C EFFICIENCY (%) Efficiency VOUT = 12V 1A 90 85 80 75 70 65 60 0 0.2 0.4 0.6 0.8 1.0 0 5 10 15 20 25 30 INPUT VOLTAGE (V) 2 200 mA 200 mA 1 1A VOUT = 3V 0.6 125C 150C 0.4 SWITCH CURRENT (A) 0 -75 -50 -25 0 25 50 75 100 125 150 JUNCTION TEMPERATURE (C) 35 40 Minimum Operating Voltage NORMALIZED FEEDBACK VOLTAGE (mV) Line Regulation Normalized to V IN = 10V VOUT = 5V ILOAD = 500mA TJ = 25 STANDBY QUIESCENT CURRENT (A) Feedback Pin Current 100 75 50 25 0 -25 -50 -75 -100 -75 -50 -25 0 25 50 75 100 125 150 5.0 4.5 4.0 INPUT VOLTAGE (V) 14 12 10 8 6 4 2 0 -2 -4 -6 0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 -75 -50 -25 0 VOUT = 1.23V ILOAD = 200 mA 25 50 75 100 125 150 5 10 15 20 25 30 JUNCTION TEMPERATURE (C) INPUT VOLTAGE (V) JUNCTION TEMPERATURE (C) Normalized Output Voltage 100 OUTPUT VOLTAGE CHANGE (mV) Oscillator Frequency +8 +6 NORMALIZED FREQUENCY (%) Dropout Voltage 2.0 INPUT-OUTPUT DIFFERENTIAL (V) 75 50 25 0 -25 -50 -75 VIN = 12V ILOAD = 200mA Normalized to TJ = 25C Normalized at 25C 1.5 ILOAD = 1A VOUT = 5% R IND = 0.2 +4 +2 0 -2 -4 --6 VIN = 40V 1.0 ILOAD = 200 mA 0.5 -100 -75 -50 -25 0 25 50 75 100 125 150 VIN = 12V -8 -75 -50 -25 0 25 50 75 100 125 150 JUNCTION TEMPERATURE (C) 0 -75 -50 -25 0 25 50 75 100 125 150 JUNCTION TEMPERATURE (C) JUNCTION TEMPERATURE (C) LM2575 6 August 1999 LM2575 Micrel Typical Performance Characteristics (Circuit of Figure 1) Load Transient Response Switching Waveforms +100mV Output Voltage Change 0 -100mV A 10V 0 B 1A 0 C 1.0A Output Current 0.5A 0 V OUT = 5V D 100S/div. 1A .5A 0 V OUT = 5V VIN = 20V A: Output pin voltage 10V/div B: Output pin current 1A/div C: Inductor current 0.5A/div D: Output ripple voltage 20 mV/div. AC coupled Test Circuits and Layout Guidelines FEEDBACK +VIN 4 Horizontal Time Base: 5s/div LM2575 1 7V - 40V UNREGULATED DC INPUT + 100 F C IN GND 3 ON/OFF 5 2 OUTPUT L1 330 H D1 MBR360 + VOUT 5.00V C OUT 470F R2 R1 L O A D C IN -- 100F, 75V Aluminum Electrolytic C OUT -- 470F, 15V Aluminum Electrolytic D1 -- Schottky, MBR360 L1 -- 330H, 415-0926 (AIE) R1 -- 1k, 0.01% R2 -- 3.065k, 0.01% 5-pin TO-220 socket--2936 (Loranger Mfg. Co.) 4-pin TO-3 socket--8112-AG7 (Augat Inc.) FEEDBACK +VIN 4 LM2575-5.0 1 7V - 40V UNREGULATED DC INPUT + 100 F C IN GND 3 ON/OFF 5 2 OUTPUT L1 330 H D1 MBR360 + VOUT 5.00V C OUT 220F L O A D C IN -- 100F, 75V Aluminum Electrolytic C OUT -- 330F, 15V Aluminum Electrolytic D1 -- Schottky, MBR360 L1 -- 330H, 415-0926 (AIE) 5-pin TO-220 socket--2936 (Loranger Mfg. Co.) 4-pin TO-3 socket--8112-AG7 (Augat Inc.) Note: Pin numbers are for TO-220 Package Figure 1. As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring inductance generate voltage transients which can cause problems. For minimal stray inductance and ground loops, the length of the leads indicated by heavy lines should be kept as short as possible. Single-point grounding (as indicated) or ground plane construction should be used for best results. Block Diagrams VIN FEEDBACK 1 4 3.1k INTERNAL REGULATOR ON/OFF 5 ON/OFF VIN 1 INTERNAL REGULATOR ON/OFF 5 ON/OFF FIXED GAIN ERROR AMP FIXED GAIN ERROR AMP COMPARATOR 1 AMP SWITCH FEEDBACK + 1.0k 4 + + - COMPARATOR 1 AMP SWITCH - + - DRIVER DRIVER 2 1.23V BAND-GAP REFERENCE OUTPUT 1.23V BAND-GAP REFERENCE 2 OUTPUT 52 kHz OSCILLATOR RESET THERMAL SHUTDOWN CURRENT LIMIT 3 GND 52 kHz OSCILLATOR RESET THERMAL SHUTDOWN CURRENT LIMIT 3 GND Note: Pin numbers are for the TO-220 package Fixed Regulator August 1999 7 Adjustable Regulator M2575 LM2575 Micrel Package Information 0.780 MAX (19.812) PIN 1 0.030-0.110 RAD (0.762-2.794) .2500.005 (6.3500.127) 0.0250.015 (0.6350.381) 0.1300.005 (3.3020.127) 0.040 TYP (1.016) 0.020 (0.508) 0.290-0.320 (7.336-8.128) 0-10 0.020 MIN (0.508) 0.125 MIN (3.175) 0.009-0.015 (0.229-0.381) 0.0180.003 (0.4570.076) 0.1000.010 (2.5400.254) +0.025 -0.015 +0.635 8.255 -0.381 0.325 ( ) 16-Pin DIP (N) PIN 1 0.301 (7.645) 0.297 (7.544) DIMENSIONS: INCHES (MM) 0.027 (0.686) 0.031 (0.787) 0.050 (1.270) TYP 0.016 (0.046) TYP 0.094 (2.388) 0.090 (2.286) 0.609 (15.469) 0.605 (15.367) 7 TYP 0.015 R (0.381) 0.015 (0.381) SEATING MIN PLANE 0.103 (2.616) 0.099 (2.515) 0.297 (7.544) 0.293 (7.442) 0.022 (0.559) 0.018 (0.457) 5 TYP 10 TYP 0.330 (8.382) 0.326 (8.280) 0.032 (0.813) TYP 0.408 (10.363) 0.404 (10.262) 24-Pin Wide SOP (WM) LM2575 8 August 1999 LM2575 0.150 D 0.005 (3.81 D 0.13) 0.400 0.015 (10.16 0.38) 0.108 0.005 (2.74 0.13) 0.241 0.017 (6.12 0.43) 0.177 0.008 (4.50 0.20) 0.050 0.005 (1.27 0.13) Micrel 0.578 0.018 (14.68 0.46) SEATING PLANE 7 Typ. 0.550 0.010 (13.97 0.25) 0.067 0.005 (1.70 0.127) 0.268 REF (6.81 REF) 0.032 0.005 (0.81 0.13) 0.018 0.008 (0.46 0.20) 0.103 0.013 (2.620.33) Dimensions: inch (mm) 5-Lead TO-220 (T) 0.4050.005 0.065 0.010 202 0.0500.005 0.176 0.005 0.060 0.005 0.3600.005 0.6000.025 SEATING PLANE 0.004 +0.004 -0.008 0.0670.005 DIM. = INCH 0.032 0.003 8 MAX 0.015 0.002 0.100 0.01 5-Lead TO-263 (T) August 1999 9 M2575 LM2575 Micrel LM2575 10 August 1999 LM2575 Micrel August 1999 11 M2575 LM2575 Micrel MICREL INC. 1849 FORTUNE DRIVE TEL SAN JOSE, CA 95131 WEB USA + 1 (408) 944-0800 FAX + 1 (408) 944-0970 http://www.micrel.com This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. (c) 1999 Micrel Incorporated LM2575 12 August 1999 |
Price & Availability of LM2575BN |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |