View UPG2163T5N-E2-A_731469.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

GaAs INTEGRATED CIRCUIT
PG2163T5N
SPDT SWITCH FOR 2.4 GHz AND 6 GHz DUAL-BAND WIRELESS LAN
DESCRIPTION
The PG2163T5N is GaAs MMIC SPDT (Single Pole Double Throw) switch which was developed for 2.4 GHz and 6 GHz dual-band wireless LAN. This device can operate frequency from 2.4 GHz band and 6 GHz band, having the low insertion loss and high isolation. This device is housed in a 6-pin plastic TSON (Thin Small Out-line Non-leaded) package. And this package is able to high-density surface mounting.
FEATURES
* Operating frequency * Switch control voltage * Low insertion loss * High isolation * Handling power : f = 2.4 to 2.5 GHz and 4.9 to 6.0 GHz : Vcont (H) = 2.8 to 5.0 V (3.0 V TYP.) : Vcont (L) = -0.3 to 0.3 V (0 V TYP.) : Lins1 = 0.40 dB TYP. @ f = 2.4 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins2 = 0.50 dB TYP. @ f = 4.9 to 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL1 = 38 dB TYP. @ f = 2.4 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL2 = 30 dB TYP. @ f = 4.9 to 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Pin (1 dB) = +31.0 dBm TYP. @ f = 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Pin (1 dB) = +29.0 dBm TYP. @ f = 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V * High-density surface mounting : 6-pin plastic TSON package (1.5 x 1.5 x 0.37 mm)
APPLICATIONS
* Dual-band wireless LAN (IEEE802.11a + b/g)
ORDERING INFORMATION
Part Number Order Number Package 6-pin plastic TSON (Pb-Free) Marking G4X Supplying Form * Embossed tape 8 mm wide * Pin 1, 6 face the perforation side of the tape * Qty 3 kpcs/reel
PG2163T5N-E2
PG2163T5N-E2-A
Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: PG2163T5N
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
Document No. PG10626EJ01V0DS (1st edition) Date Published July 2006 NS CP(K)
PG2163T5N
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
(Top View) (Top View)
(Bottom View)
Pin No. 1 Pin Name GND Vcont2 OUT2 (RX) OUT1 (TX) Vcont1
IN (ANT)
1
6
1
6
6
1
2 3
G4X
Vcont1 High Low Parameter Parameter
2
5
2
5
5
2
4 5
6
3
4
3
4
4
3
Remark Exposed pad : GND
TRUTH TABLE
Vcont2 Low High IN (ANT)-OUT1 (TX) OFF ON IN (ANT)-OUT2 (RX) ON OFF
ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified)
Symbol Vcont Pin TA Tstg Ratings -6.0 to +6.0 +32 -45 to +85 -55 to +135 Unit V dBm C C
Switch Control Voltage Input Power Operating Ambient Temperature Storage Temperature
RECOMMENDED OPERATING RANGE (TA = +25C, unless otherwise specified)
Symbol Vcont (H) Vcont (L) f1 f2 MIN. 2.8 -0.3 2.4 4.9 TYP. 3.0 0 - - MAX. 5.0 0.3 2.5 6.0 Unit V V GHz GHz
Switch Control Voltage (H) Switch Control Voltage (L) Operating Frequency 1 Operating Frequency 2
2
Data Sheet PG10626EJ01V0DS
PG2163T5N
ELECTRICAL CHARACTERISTICS (TA = +25C, Vcont (H) = 3.0 V, Vcont otherwise specified)
Parameter Insertion Loss 1 Insertion Loss 2 Isolation 1 Isolation 2 Input Return Loss 1 Input Return Loss 2 Output Return Loss 1 Output Return Loss 2 1 dB Loss Compression Note Input Power 1 1 dB Loss Compression Note Input Power 2 Input 3rd Order Distortion Intercept Point Switch Control Current Switch Control Speed Icont tSW 50% CTL to 90/10% - - 0.1 50 1.0 - Symbol Lins1 Lins2 ISL1 ISL2 RLin1 RLin2 RLout1 RLout2
(L)
= 0 V, Z0 = 50 , DC blocking capacitors = 4 pF, unless
Test Conditions f = 2.4 to 2.5 GHz f = 4.9 to 6.0 GHz f = 2.4 to 2.5 GHz f = 4.9 to 6.0 GHz f = 2.4 to 2.5 GHz f = 4.9 to 6.0 GHz f = 2.4 to 2.5 GHz f = 4.9 to 6.0 GHz
MIN. - - 35 27 - - - - - - -
TYP. 0.40 0.50 38 30 15 15 15 15 +31.0
MAX. 0.60 0.80 - - - - - - - - -
Unit dB dB dB dB dB dB dB dB dBm
Pin (1 dB) 1 f = 2.4 to 2.5 GHz
Pin (1 dB) 2 f = 4.9 to 6.0 GHz
+29.0
dBm
IIP3
+55
dBm
A
ns
Note Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear range. Caution This device is used it is necessary to use DC blocking capacitors.
Data Sheet PG10626EJ01V0DS
3
PG2163T5N
EVALUATION CIRCUIT
4 pF 1 6 IN (ANT)
Vcont2 1 000 pF
2
5 1 000 pF
Vcont1
OUT2 (RX) 4 pF
3
4 4 pF
OUT1 (TX)
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
4
Data Sheet PG10626EJ01V0DS
PG2163T5N
MOUNTING PAD DIMENSIONS 6-PIN PLASTIC TSON (UNIT: mm)
MOUNTING PAD
0.3 0.5 0.3
1.0
0.3 0.2
0.3
SOLDER PAD
0.475 0.25 0.475
0.35 0.55 0.15
0.25
Solder thickness : 0.08 mm
Remark The mounting pad layouts in this document are for reference only.
0.5
0.5
0.5
0.5
Data Sheet PG10626EJ01V0DS
5
PG2163T5N
PACKAGE DIMENSIONS 6-PIN PLASTIC TSON (UNIT: mm)
(Top View)
1.50.1
(Side View)
(Bottom View)
0.30.07
0.50.06
1.50.1
0.37+0.03 -0.05
0.20.1
0.2+0.07 -0.05
0.70.1
6
Data Sheet PG10626EJ01V0DS
1.20.1
PG2163T5N
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220C or higher Preheating time at 120 to 180C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (terminal temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260C or below : 10 seconds or less : 60 seconds or less : 12030 seconds : 3 times : 0.2%(Wt.) or below : 260C or below : 10 seconds or less : 1 time : 0.2%(Wt.) or below : 350C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 WS260 Condition Symbol IR260
For soldering
Preheating temperature (package surface temperature) : 120C or below
Caution Do not use different soldering methods together (except for partial heating).
Data Sheet PG10626EJ01V0DS
7
4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279
Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information.
Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*)
If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.

▲Up To Search▲

Price & Availability of UPG2163T5N-E2-A

	To Download UPG2163T5N-E2-A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .