|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
(R) ISL8601 Data Sheet March 23, 2007 FN6449.0 PRELIMINARY* *All functional details and specifications are preliminary and subject to change Single-Phase, PMBus-Enabled PWM Controller with Integrated FET Drivers The ISL8601 is a single-phase PWM controller with integrated MOSFET drivers utilizing analog voltage mode control. The ISL8601 features extensive PMBus compliance that enables rapid and flexible power supply design and comprehensive product evaluation and testing. Exceptional flexibility in the customization of operating parameters and system monitoring functions is provided via the large PMBus command set. The ISL8601 supports both low-side MOSFET rDS(ON) and Inductor DCR current sensing. Programmable temperature compensation for sensed current values is provided to ensure maximum accuracy. In addition to the I2C interface, select PMBus commands for the ISL8601 can also be programmed via external resistors, bringing the power and flexibility of PMBus into low-cost power supply systems. Features * Input Voltage Range: +1.8V to 13.2V * VBIAS Voltage Range: +4.5V to 13.2V * Minimum Output Voltage: +0.5V * 1.0% System Accuracy Over the Range of -40C to +85C When Using the 0.8V Reference * Internal Reference Voltage Programmable from 0.4V to 0.9V in 4mV Steps * Integrated 2A to 4A MOSFET Drivers * External Frequency Synchronization * Selectable Phase Delay: 0, 90, 120, 180, 240, or 270 * Precision MOSFET rDS(ON) or Inductor DCR Current Sensing * Voltage Feedforward Compensation Ordering Information PART NUMBER TEMP RANGE (C) ISL8601IRZ -40 to +85 PACKAGE PKG. DWG. # 40 Ld 6x6 QFN L40.6x6 * Extensive PMBus Compliance * Broad PMBus Programmability Including Output Voltage, Overvoltage Threshold, Overcurrent Threshold, Overtemperature Threshold, Switching Frequency, TurnOn and Turn-Off * PMBus Monitoring of Load Current, Input Voltage, Output Voltage and Temperature * PMBus Programming Via I2C Interface * Resistor Programming of Select PMBus Parameters NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. Pinout ISL8601 (40 LD 6x6 QFN) RCONF2 RCONF1 RADDR THERM REG5V VBIAS UVLO C50A * Operating Frequency Range: 200kHz to 2MHz * Internal and External Temperature Measurement * Overvoltage, Undervoltage and Overtemperature Protection * Low-Side and High-Side Overcurrent Protection * Programmable Supply Sequencing and Tracking 30 RGND 29 PGND 28 LGATE GND BOTTOM SIDE PAD 27 PVCC 26 PHASE 25 UGATE 24 BOOT 23 HSOC 22 DGND 21 PGOOD 11 12 13 14 15 16 17 18 19 20 VSENSP SMBDAT VSENSN SMBALRT SMBCLK FB VMON EN SYNC C25D ROV 40 39 38 37 36 35 34 33 32 31 ROSC 1 ISENSN 2 ISENSP 3 N/C 4 N/C 5 LSOC 6 AGND 7 C25A 8 SS 9 COMP 10 VFF * Digital Soft-Start with Multiple Soft-Start Modes * Multiple Programmable Fault-Handling Modes * Multiple Prebiased Startup Options * Differential Remote Voltage Sensing * Power-Good Output with Programmable Delay Applications * Ethernet Routers and Switches * Point-of-Load Modules * Industrial Power Management 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2007. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL8601 Functional Block Diagram UVLO VBIAS THERM EXTERNAL TEMP MEASUREMENT INTERNAL TEMP SENSE RESISTOR DECODE LDO2 LDO1 REG5V C50A RCONF1 RCONF2 ROSC ROV RADDR UVLO DETECT LDO3 LDO4 C25D C25A LSOC HSOC CURRENT SENSE ISENSP ISENSN 8-BIT MEASUREMENT ADC SMBDAT SMBCLK SMBALRT SERIAL INTERFACE MAIN CONTROL LOGIC PGOOD GENERATOR PGOOD EN VMON VSENSP DIFA VSENSN VFF AV = 1 OSCILLATOR PWM COMP SOFT-START CIRCUIT DRIVER CONTROL BOOT UGATE PHASE PVCC LGATE 1.024V REFERENCE FB COMP 8-BIT DAC EA PGND SYNC SS AGND DGND RGND 2 FN6449.0 March 23, 2007 ISL8601 Typical Application Circuit +4.5V to +13.2V RVBIAS RREG5V CVBIAS CREG5V CPVCC RBOOT VBIAS VFF CVFF RUVLO1 UVLO RUVLO2 SYNC EN PGOOD C50A C50A C25A C25D CSS C25A C25D SS LSOC COMP C2 C1 I2C Bus 3 SMBDAT SMBCLK SMBALRT R2 FB R1 VMON RADDR RCONF1 RCONF2 ROSC ROV RADDR RCONF0 RCONF2 ROSC ROV AGND DGND VSENSP CSEN VSENSN THERM RGND RTHERM RFB ROS C3 R3 LGATE PGND ISENSP ISENSN RLSOC CLSOC UGATE PHASE Q2 COUT REG5V PVCC HSOC BOOT CHSOC Q1 LOUT VOUT RHSOC DBOOT RVFF All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 3 FN6449.0 March 23, 2007 ISL8601 Package Outline Drawing L40.6x6 40 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 3, 10/06 4X 4.5 6.00 A B 6 PIN 1 INDEX AREA 31 30 36X 0.50 40 1 6 PIN #1 INDEX AREA 4 . 10 0 . 15 6.00 21 (4X) 0.15 20 TOP VIEW 40X 0 . 4 0 . 1 BOTTOM VIEW 11 10 0.10 M C A B 4 0 . 23 +0 . 07 / -0 . 05 SEE DETAIL "X" 0.10 C BASE PLANE SIDE VIEW ( 36X 0 . 5 ) SEATING PLANE 0.08 C C 0 . 90 0 . 1 ( 5 . 8 TYP ) ( 4 . 10 ) C ( 40X 0 . 23 ) ( 40X 0 . 6 ) TYPICAL RECOMMENDED LAND PATTERN 0 . 2 REF 5 0 . 00 MIN. 0 . 05 MAX. DETAIL "X" NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 indentifier may be either a mold or mark feature. 4 FN6449.0 March 23, 2007 |
Price & Availability of ISL8601 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |