|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Data Sheet, Rev. 1.3, April 2004 HYB25L512160AC-7.5 512MBit Mobi le- RAM S t an d a r d T e m p e r at u r e R an g e M e m or y P r o du c t s Never stop thinking. The information in this document is subject to change without notice. Edition 2004-04 Published by Infineon Technologies AG, St.-Martin-Strasse 53, 81669 Munchen, Germany (c) Infineon Technologies AG 2004. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Data Sheet, Rev. 1.3, April 2004 HYB25L512160AC-7.5 512MBit Mobi le- RAM S t an d a r d T e m p e r at u r e R an g e M e m or y P r o du c t s Never stop thinking. HYB25L512160AC-7.5 Revision History: Previous Revision: Page all Rev. 1.3 Rev. 1.2 2004-04 2003-01 Subjects (major changes since last revision) Delete extended temperature range (HYE25L512160AC-7.5) We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: techdoc.mp@infineon.com Template: mp_a4_v2.3_2004-01-14.fm HYB25L512160AC-7.5 512MBit Mobile-RAM Table of Contents 1 1.1 1.2 2 2.1 3 3.1 3.2 3.2.1 3.2.1.1 3.2.1.2 3.2.1.3 3.2.1.4 3.2.2 3.2.2.1 3.2.2.2 3.3 3.4 3.4.1 3.4.2 3.4.3 3.4.4 3.4.5 3.4.5.1 3.4.5.2 3.4.5.3 3.4.5.4 3.4.5.5 3.4.6 3.4.6.1 3.4.6.2 3.4.6.3 3.4.6.4 3.4.7 3.4.8 3.4.8.1 3.4.8.2 3.4.9 3.4.9.1 3.4.9.2 3.4.10 3.4.10.1 3.5 4 4.1 4.2 4.3 4.4 4.5 5 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power On and Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Burst Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Burst Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAS Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Write Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extended Mode Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Partial Array Self Refresh (PASR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Compensated Self Refresh (TCSR) with On-Chip Temperature Sensor . . . . . . . . State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No Operation (NOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MODE REGISTER SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ACTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . READ Burst Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock Suspend Mode for READ Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . READ - DQM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . READ to WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . READ to PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WRITE Burst Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock Suspend Mode for WRITE Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WRITE - DQM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WRITE to READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BURST TERMINATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUTO PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONCURRENT AUTO PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUTO REFRESH and SELF REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUTO REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SELF REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . POWER DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DEEP POWER DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Function Truth Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Operation Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Capacitances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 12 13 13 14 15 15 15 15 16 16 17 18 19 19 20 21 22 26 26 27 27 28 29 32 33 34 34 35 36 36 37 38 38 39 40 41 42 45 45 45 46 47 48 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Data Sheet 5 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Standard Ballout 512M Mobile-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Block Diagram of Stacked Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Functional Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Power-Up Sequence and Mode Register Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Mode Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Extended Mode Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 State Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Address / Command Inputs Timing Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 No Operation Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Mode Register Set Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Mode Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 ACTIVE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Bank Activate Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 READ Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Basic READ Timing Parameters for DQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Single READ Burst (CAS Latency = 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Single READ Burst (CAS Latency = 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Consecutive READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Random READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Non-Consecutive READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Terminating a READ Burst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Clock Suspend Mode for READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 READ Burst - DQM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 READ to WRITE Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 READ to PRECHARGE Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 WRITE Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Basic WRITE Timing Parameters for DQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 WRITE Burst (CAS Latency = 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 WRITE Burst (CAS Latency = 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Consecutive WRITE Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Random WRITE Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Non-Consecutive WRITE Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Terminating a WRITE Burs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Clock Suspend Mode for WRITE Bursts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 WRITE Burst - DQM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 WRITE to READ Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 WRITE to PRECHARGE Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 BURST TERMINATE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 PRECHARGE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 READ with Auto Precharge Interrupted by READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 READ with Auto Precharge Interrupted by WRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 WRITE with Auto Precharge Interrupted by READ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 WRITE with Auto Precharge Interrupted by WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 AUTO REFRESH Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 AUTO REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 SELF REFRESH Entry Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 SELF REFRESH Entry and Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 POWER DOWN Entry Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 POWER DOWN Entry and Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Package FBGA-54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Data Sheet 6 Rev. 1.3, 2004-04 512MBit Mobile-RAM HYB25L512160AC-7.5 1 1.1 * * * * * * * * * * Overview Features 2 x 4 banks x 4 Mbit x 16 organisation ( Two 256MBit chips stacked in multi-chip package) Fully synchronous to positive clock edge Four internal banks for concurrent operation Programmable CAS latency: 2, 3 Programmable burst length: 1, 2, 4, 8 or full page Programmable wrap sequence: sequential or interleaved Auto refresh and self refresh modes 8192 refresh cycles / 64ms Auto precharge Operating temperature range Commerical (0C to +70C) 54-ball FBGA package (12.0 mm x 8.0 mm x 1.4 mm) Power Saving Features: * * * * * Low supply voltages: VDD = 2.3V .. 3.6V, VDDQ = 1.65V .. 1.95V or 2.3V .. 3.6V Optimized self refresh (ICC6) and standby currents (ICC2 / ICC3) Programmable Partial Array Self Refresh (PASR) Temperature Compensated Self-Refresh (TCSR), controllable by on-chip temperature sensor Power-Down and Deep Power Down modes Performance -7.5 1.65 ...1.95 105 CL = 2 or 3 CL = 2 Table 2 Item Banks Rows Columns Memory Addressing Scheme Addresses BA0, BA1 A0 - A12 A0 - A8 8.0 9.5 9.5 2.3 ...3.6 133 6.0 7.5 9.5 V MHz ns ns ns Unit Table 1 VDDQ Part Number Speed Code Clock Frequency (fCKmax) Access Time (tACmax) Clock Cycle Time (tCKmin) CL = 3 Data Sheet 7 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Overview 1.2 Description The HYB25L512160AC consists of two 256MBit high-speed CMOS, dynamic random-access memories each of them containing 268,435,456 bits. Each chip is internally configured as a quad-bank DRAM. The HYB25L512160AC achieves high speed data transfer rates by employing a chip architecture that prefetches multiple bits and then synchronizes the output data to the system clock. Read and write accesses are burstoriented; accesses start at a selected location and continue for a programmed number of locations (1, 2, 4, 8 or full page) in a programmed sequence. The device operation is fully synchronous: all inputs are registered at the positive edge of CLK. The HYB25L512160AC is especially designed for mobile applications: it adds many features to save power, like low operating voltages. Additionally, current consumption in self refresh mode can further be reduced by using the programmable Partial Array Self Refresh (PASR) and Temperature Compensated Self Refresh (TCSR). A conventional data-retaining power down (PD) mode is available as well as a non-data-retaining deep power down (DPD) mode. The HYB25L512160AC is housed in a 54-ball "chip-size" FBGA package. It is available in Commercial (0C to 70C) temperature range. Table 3 Type 1) Ordering Information Description 133 MHz 2 x 4 Banks x 4 Mbit x 16 LP-SDRAM Package FBGA-54 Commercial Temperature Range HYB25L512160AC-7.5 1) HYB: Designator for memory products (HYB: standard temp. range) 25L: 2.5V Mobile-RAM 512: 512 MBit density 160: 16 bit interface width A: die revision C : lead-containing product Data Sheet 8 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Pin Configuration 2 Pin Configuration 1 2 DQ15 DQ13 DQ11 DQ9 CS1 CLK A11 A7 A5 3 7 A B C D E F G H J 8 DQ0 DQ2 DQ4 DQ6 LDQS RAS BA1 A1 A2 9 VSS DQ14 DQ12 DQ10 DQ8 UDQM A12 A8 VSSQ VDDQ VSSQ VDDQ VSS CKE A9 A6 A4 VDDQ VSSQ VDDQ VSSQ VDD CAS BA0 A0 A3 VDD DQ1 DQ3 DQ5 DQ7 WE CS0 A10/AP VSS VDD MPPD0050 Figure 1 Note Standard Ballout 512M Mobile-RAM 1. 54 - Ball FBGA Package (Top View) CS0 CS1 BA0 - BA1 A0 - A12 RAS CAS WE CKE0 BA0 - BA1: SDRAMs D0 - D1 A0 - A12: SDRAMs D0 - D1 RAS: SDRAMs D0 - D1 CAS: SDRAMs D0 - D1 WE: SDRAMs D0 - D1 CKE: SDRAMs D0 - 1 LDQM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 UDQM DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 CS LDQM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDQM I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 D0 CS LDQM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 UDQM I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 D1 MPBD1920 Figure 2 Block Diagram of Stacked Configuration Data Sheet 9 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Pin Configuration 2.1 Table 4 CLK CKE Pin Description Pin Description Function Clock: all inputs are sampled on the positive edge of CLK. Clock Enable: CKE HIGH activates and CKE LOW deactivates internal clock signals, device input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER-DOWN and SELF REFRESH operation (all banks idle), ACTIVE POWER-DOWN (row active in any bank) or SUSPEND (access in progress). Input buffers, excluding CLK and CKE are disabled during POWER-DOWN and SELF-REFRESH. Chip Select: All commands are masked when CS is registered HIGH. CS provides for external bank selection on systems with multiple memory banks. CS is considered part of the command code Command Inputs: RAS, CAS and WE (along with CS) define the command being entered. Input Input Symbol Type CS (CS0, CS1) RAS, CAS, WE DQ0 DQ15 Input Input I/O Data Inputs/Output: Bi-directional data bus (16 bit) Input/Output Mask: input mask signal for WRITE cycles and output enable for READ cycles. For WRITEs, DQM acts as a data mask when HIGH. For READs, DQM acts as an output enable and places the output buffers in High-Z state when HIGH (two clocks latency) . LDQM corresponds to DQ0 - DQ7, UDQM corresponds to DQ8 - DQ15. Bank Address Inputs: BA0 and BA1 define to which bank an ACTIVATE, READ, WRITE or PRECHARGE command is being applied. BA0, BA1 also determine which mode register is to be loaded during a MODE REGISTER SET command (MRS or EMRS). Address Inputs: A0 - A12 define the row address during an ACTIVE command cycle. A0 A8 define the column address during a READ or WRITE command cycle. In addition, A10 (= AP) controls Auto Precharge operation at the end of the burst read or write cycle. During a PRECHARGE command, A10 (= AP) in conjunction with BA0, BA1 controls which bank(s) are to be precharged: if A10 is HIGH, all four banks will be precharged regardless of the state of BA0 and BA1; if A10 is LOW, BA0, BA1 define the bank to be precharged. During MODE REGISTER SET commands, the address inputs hold the op-code to be loaded. I/O Power Supply: Isolated power for DQ output buffers for improved noise immunity: DQM Input (LDQM, UDQM) BA0, BA1 Input A0 - A12 Input VDDQ VSSQ VDD VSS Supply Supply Supply Supply VDDQ = 1.65V..1.95V; or 2.3V..3.6V I/O Ground Power Supply: Power for the core logic and input buffers. VDD = 2.3V..3.6V Ground Data Sheet 10 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Pin Configuration CKE CLK CS RAS CAS WE Control Logic Command Decode Bank 1 Bank 2 Bank 3 Bank 0 Row Address Latch & Decoder Row Address Mux Mode Registers 13 13 13 8192 Bank 0 Memory Array (8192 x 512 x 16) 2 Data Output Reg. 16 16 Data Input Reg. 2 LDQM UDQM Address Register Sense Amplifier A0-A12 BA0,BA1 15 13 Refresh Counter Bank Column Logic DQ0DQ15 2 IO Gating DQM Mask Logic 2 9 Column Address Counter / Latch 9 Column Decoder Figure 3 Functional Block Diagram Data Sheet 11 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3 Functional Description The 512 Mbit Mobile-RAM consists of two 256MBit high-speed CMOS, dynamic random-access memories each of them containing 268,435,456 bits. Each chip is internally configured as a quad-bank DRAM. READ and WRITE accesses to the Mobile-RAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed (BA0, BA1 select the banks, A0 - A12 select the row). The address bits registered coincident with the READ or WRITE command are used to select the starting column location for the burst access. Prior to normal operation, the Mobile-RAM must be initialized. The following sections provide detailed information covering device initialization, register definition, command description and device operation. 3.1 Power On and Initialization The Mobile-RAM must be powered up and initialized in a predefined manner (see Figure 4). Operational procedures other than those specified may result in undefined operation. VDD VDDQ 200s CLK CKE tCK tRP tRFC tRFC tMRD tMRD Command Address A10 NOP PRE ARF ARF MRS CODE MRS CODE CODE NOP ACT NOP RA NOP RA All Banks CODE BA0,BA1 BA0=L BA1=L BA0=L BA1=H NOP BA DQM DQ High-Z Power-up: VDD and CK stable Load Mode Register Load Ext. Mode Register = Don't Care Figure 4 Power-Up Sequence and Mode Register Sets No power sequencing is specified during power up or power down provided that one of the following two criteria is met: Data Sheet 12 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description * * VDD and VDDQ are driven from a single power converter output VDDQ is driven after or with VDD such that VDDQ < VDD + 0.3 V After all power supply voltages are stable, and the clock is stable, the Mobile-RAM requires a 200s delay prior to applying a command other than DESELECT or NOP. CKE and DQM must be held high throughout the entire power-up sequence. Once the 200s delay has been satisfied, the following command sequence shall be applied (see Figure 4): * * * a PRECHARGE ALL command; at least 8 AUTO REFRESH commands; two MODE REGISTER SET commands for the Mode Register and Extended Mode Register Following these cycles, the Mobile-RAM is ready for normal operation. 3.2 3.2.1 Register Definition Mode Register The Mode Register is used to define the specific mode of operation of the Mobile-RAM. This definition includes the selection of a burst length, a burst type, a CAS latency, and a write burst mode. The Mode Register is programmed via the MODE REGISTER SET command (with BA0 = 0 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power. BA1 BA0 A12 A11 A10 0 0 0 0 0 A9 WB A8 0 A7 0 A6 A5 A4 A3 BT A2 A1 A0 Address Bus Mode Register CAS Latency Burst Length A9 0 1 Write Burst Mode Burst Write Single Write A3 0 1 Burst Type Sequential Interleave A6 0 0 0 0 1 1 1 1 A5 0 0 1 1 0 0 1 1 A4 0 1 0 1 0 1 0 1 CAS Latency Reserved 2 3 A2 0 0 0 0 1 A1 0 0 1 1 0 0 1 1 A0 0 1 0 1 0 1 0 1 Burst Length Sequential Interleave 1 2 4 8 1 2 4 8 Reserved Reserved Reserved 1 1 1 full page Figure 5 Mode Register Definition Address bits A0-A2 specify the burst length, A3 the burst type, A4-A6 the CAS latency, A9 the write burst mode, while bits A7-A8 and A10-A12 shall be written to zero. Data Sheet 13 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description The Mode Register must be loaded when all banks are idle, and the controller must wait the specified time before initiating the subsequent operation. Violating either of these requirements results in unspecified operation. Reserved states should not be used, as unknown operation or incompatibility with future versions may result. 3.2.1.1 Burst Length READ and WRITE accesses to the Mobile-RAM are burst oriented, with the burst length being programmable. The burst length determines the maximum number of column locations that can be accessed for a given READ or WRITE command. Burst lengths of 1, 2, 4, 8 locations are available for both the sequential and interleaved burst types, and a full-page burst mode is available for the sequential burst type. When a READ or WRITE command is issued, a block of columns equal to the burst length is effectively selected. All accesses for that burst take place within this block, meaning that the burst wraps within the block if a boundary is reached. The block is uniquely selected by A1-A8 when the burst length is set to two, by A2-A8 when the burst length is set to four and by A3-A8 when the burst length is set to eight. The remaining (least significant) address bit(s) is (are) used to select the starting location within the block. Full page bursts wrap within the page if the boundary is reached. Please note that full page bursts do not selfterminate; this implies that full-page read or write bursts with Auto Precharge are not legal commands. Table 5 Burst Length 2 4 0 0 1 1 8 0 0 0 0 1 1 1 1 Full Page Note: 1. For a burst length of two, A1-Ai select the two-data-element block; A0 selects the first access within the block. 2. For a burst length of four, A2-Ai select the four-data-element block; A0-A1 select the first access within the block. 3. For a burst length of eight, A3-Ai select the eight-data-element block; A0-A2 select the first access within the block. 4. For a full page burst, A0-Ai select the starting data element. 5. Whenever a boundary of the block is reached within a given sequence, the following access wraps within the block. n 0 0 1 1 0 0 1 1 n Burst Definition Starting Column Address A2 A1 A0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 n Order of Accesses Within a Burst Sequential 0-1 1-0 0-1-2-3 1-2-3-0 2-3-0-1 3-0-1-2 0-1-2-3-4-5-6-7 1-2-3-4-5-6-7-0 2-3-4-5-6-7-0-1 3-4-5-6-7-0-1-2 4-5-6-7-0-1-2-3 5-6-7-0-1-2-3-4 6-7-0-1-2-3-4-5 7-0-1-2-3-4-5-6 Cn, Cn+1, Cn+2, ... Interleaved 0-1 1-0 0-1-2-3 1-0-3-2 2-3-0-1 3-2-1-0 0-1-2-3-4-5-6-7 1-0-3-2-5-4-7-6 2-3-0-1-6-7-4-5 3-2-1-0-7-6-5-4 4-5-6-7-0-1-2-3 5-4-7-6-1-0-3-2 6-7-4-5-2-3-0-1 7-6-5-4-3-2-1-0 not supported Data Sheet 14 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.2.1.2 Burst Type Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the burst type and is selected via bit A3. The ordering of accesses within a burst is determined by the burst length, the burst type and the starting column address, as shown in Table 5. 3.2.1.3 CAS Latency The CAS latency is the delay, in clock cycles, between the registration of a READ command and the availability of the first piece of output data. The latency can be programmed to 2 or 3 clocks. If a READ command is registered at clock edge n, and the latency is m clocks, the data will be available with clock edge n + m (for details please refer to the READ command description). 3.2.1.4 Write Burst Mode When A9 = 0, the burst length programmed via A0-A2 applies to both read and write bursts; when A9 = 1, write accesses consist of single data elements only. 3.2.2 Extended Mode Register The Extended Mode Register controls additional low power features of the device. These include the Partial Array Self Refresh (PASR) and the Temperature Compensated Self Refresh (TCSR). The Extended Mode Register is programmed via the MODE REGISTER SET command (with BA0 = 0 and BA1 = 1) and will retain the stored information until it is programmed again or the device loses power. The Extended Mode Register must be loaded when all banks are idle, and the controller must wait the specified time before initiating any subsequent operation. Violating either of these requirements result in unspecified operation. BA1 BA0 A12 A11 A10 1 0 0 0 0 A9 0 A8 0 A7 0 A6 0 A5 0 A4 A3 A2 A1 PASR A0 Address Bus Mode Register TCSR A4 A3 0 0 1 0 1 0 TCSR 70C 45C 15C A2 A1 A0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 PASR all banks 1/2 array (BA1 = 0) 1/4 array (BA1 = BA0 = 0) Reserved Reserved 1/8 array (BA1 = BA0 = RA12 = 0) 1/8 array (BA1 = BA0 = RA12 = RA11 = 0) Reserved Figure 6 Extended Mode Register Definition Address bits A0-A2 specify the Partial Array Self Refresh (PASR) and bits A3-A4 the Temperature Compensated Self Refresh (TCSR), while bits A5-A12 shall be written to zero. Data Sheet 15 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.2.2.1 Partial Array Self Refresh (PASR) Partial Array Self Refresh is power-saving feature specific to Mobile-RAMs. With PASR, self refresh may be restricted to variable portions of the total array. The selection comprises all four banks (default), two banks, one bank, half a bank, and a quarter of one bank. Data written to the non activated memory sections will get lost after a period defined by tREF (cf. Table 13). 3.2.2.2 Temperature Compensated Self Refresh (TCSR) with On-Chip Temperature Sensor DRAM devices store data as a electrical charge in tiny capacitors that require a periodic refresh in order to retain the stored information. This refresh requirement heavily depends on the die temperature: high temperature corresponds to short refresh period, and low temperature to long refresh period. The Mobile-RAM is equipped with an on-chip temperature sensor which continuously monitors the current die temperature and adjusts the refresh period in self refresh mode accordingly. By default the on-chip temperature sensor is enabled (TCSR = 00, see Figure 6 ); the other three TCSR settings use defined temperature values to adjust the self refresh period with the on-chip temperature sensor being disabled. Data Sheet 16 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.3 State Diagram Deep Power Down Power applied Power On DPDSX Precharge All PREALL DPDS REFSX REFS Self Refresh Mode Register Set MRS Idle REFA CKEL CKEH Auto Refresh Active Power Down CKEH CKEL T BS W ACT Precharge Power Down Row Active TE RI BS T RE AD WRITEA Clock Suspend WRITE READA READ CKEL CKEH WRITE WRITE READ CKEL CKEH Clock Suspend READ WRITEA WRITEA PRE PRE READ A PRE READA Clock Suspend WRITEA CKEL CKEH PRE WRITE A READ A CKEL CKEH Clock Suspend READA Precharge Automatic Sequence Command Sequence PREALL = Precharge All Banks REFS = Enter Self Refresh REFSX = Exit Self Refresh REFA = Auto Refresh DPDS = Enter Deep Power Down DPDSX = Exit Deep Power Down CKEL = Enter Power Down CKEH = Exit Power Down READ = Read w/o Auto Precharge READA = Read with Auto Precharge WRITE = Write w/o Auto Precharge WRITEA = Write with Auto Precharge ACT = Active PRE = Precharge BST = Burst Terminate MRS = Mode Register Set Figure 7 State Diagram Data Sheet 17 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4 Table 6 Command NOP ACT RD WR BST PRE ARF MRS - - Commands Command Overview CS RAS CAS WE DQM Address H L L L L L L L -- -- X H L H H H L L L -- -- X H H L L H H L L -- -- X H H H L L L H L -- -- X X X L/H L/H X X X X L H X X Bank / Row Bank / Col Bank / Col X Code X Op-Code -- -- Notes 1) 1) 2) 3) 3) 4) DESELECT NO OPERATION ACTIVE (Select bank and row) READ (Select bank and column and start read burst) BURST TERMINATE or DEEP POWER DOWN PRECHARGE (Deactivate row in bank or banks) AUTO REFRESH or SELF REFRESH (enter self refresh mode) MODE REGISTER SET Data Write / Output Enable Write Mask / Output Disable (High-Z) WRITE (Select bank and column and start write burst) L 5) 6)7) 8) 9) 9) 1) DESELECT and NOP are functionally interchangeable. 2) BA0, BA1 provide bank address, and A0 - A12 provide row address. 3) BA0, BA1 provide bank address, A0 - A8 provide column address; A10 HIGH enables the Auto Precharge feature (nonpersistent), A10 LOW disables the Auto Precharge feature. 4) This command is BURST TERMINATE if CKE is HIGH; DEEP POWER DOWN if CKE is LOW. The BURST TERMINATE command is defined for READ or WRITE bursts with Auto Precharge disabled only. 5) A10 LOW: BA0, BA1 determine which bank is precharged. A10 HIGH: all banks are precharged and BA0, BA1 are "Don't Care". 6) This command is AUTO REFRESH if CKE is HIGH; SELF REFRESH if CKE is LOW. 7) Internal refresh counter controls row and bank addressing; all inputs and I/Os are "Don't Care" except for CKE. 8) BA0, BA1 select either the Mode Register (BA0 = 0, BA1 = 0) or the Extended Mode Register (BA0 = 0, BA1 = 1); other combinations of BA0, BA1 are reserved; A0 - A12 provide the op-code to be written to the selected mode register. 9) DQM LOW: data present on DQs is written to memory during write cycles; DQ output buffers are enabled during read cycles; DQM HIGH: data present on DQs are masked and thus not written to memory during write cycles; DQ output buffers are placed in High-Z state (two clocks latency) during read cycles. Address (A0 - A12, BA0, BA1), write data (DQ0 - DQ15) and command inputs (CKE, CS, RAS, CAS, WE, DQM) are all registered on the positive edge of CLK. Figure 8 shows the basic timing parameters, which apply to all commands and operations. tCK CLK tIS tIH Input *) Valid Valid Valid tCH tCL = Don't Care *) = A0 - A12, BA0, BA1, DQ0 - DQ15, DQM, RAS, CAS, WE, CKE, CS Figure 8 Data Sheet Address / Command Inputs Timing Parameters 18 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description Due to shared command, CLK and CKE pins of this stacked configuration, commands issued to one chip may also impact the state of the second chip, even if that chip is actually deselected. Details can be found in the command descriptions below. Table 7 Parameter Clock cycle time VDDQ = 2.3V .. 3.6V VDDQ = 1.65V .. 1.95V Clock frequency Clock high-level width Clock low-level width Address, data and command input setup time Address, data and command input hold time VDDQ = 2.3V .. 3.6V VDDQ = 1.65V .. 1.95V CL = 3 CL = 2 CL = 2 or 3 CL = 3 CL = 2 or 3 fCK fCK tCH tCL tIS tIH Inputs Timing Parameters Symbol tCK -7.5 min 7.5 9.5 9.5 -- -- 2.5 2.5 1.5 0.8 max -- -- -- 133 105 -- -- -- -- ns ns ns MHz MHz ns ns ns ns -- -- -- -- Unit Notes 3.4.1 No Operation (NOP) CLK CKE CS RAS CAS WE A0-A12 BA0,BA1 = Don't Care (High) The NO OPERATION (NOP) command is used to perform a NOP to a Mobile-RAM which is selected (CS = LOW). This prevents unwanted commands from being registered during idle states. Operations already in progress are not affected. Figure 9 No Operation Command 3.4.2 DESELECT The DESELECT function (CS = HIGH) prevents new commands from being executed by the Mobile-RAM. The Mobile-RAM is effectively deselected. Operations already in progress are not affected. When issuing an access command to one chip of this stacked configuration, the other chip shall be deselected by asserting its corresponding CS pin HIGH. Data Sheet 19 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4.3 MODE REGISTER SET CLK CKE CS RAS CAS WE A0-A12 BA0,BA1 Code Code = Don't Care (High) The mode registers are loaded via inputs A0 - A12 (see mode register descriptions in Chapter 3.2). The MODE REGISTER SET command can only be issued when all banks are idle and no bursts are in progress. A subsequent execucommand cannot be issued until tMRD is met. The command may be issued to both chips in parallel (CS0 = CS1 = 0). Figure 10 Mode Register Set Command CLK Command MRS NOP Valid tMRD Address Code Valid = Don't Care Code = Mode Register / Extended Mode Register selection (BA0, BA1) and op-code (A0 - A12) Figure 11 Table 8 Parameter Mode Register Definition Timing Parameters for Mode Register Set Command Symbol min. tMRD 2 - 7.5 max. -- tCK Unit Notes MODE REGISTER SET command period Data Sheet 20 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4.4 ACTIVE CLK CKE CS RAS CAS WE A0-A12 BA0,BA1 RA BA = Don't Care BA = Bank Address RA = Row Address (High) Before any READ or WRITE commands can be issued to a bank within the Mobile-RAM, a row in that bank must be "opened" (activated). This is accomplished via the ACTIVE command and addresses A0 - A12, BA0 and BA1 (see Figure 12), which decode and select both the bank and the row to be activated. After opening a row (issuing an ACTIVE command), a READ or WRITE command may be issued to that row, subject to the tRCD specification. A subsequent ACTIVE command to a different row in the same bank can only be issued after the previous active row has been "closed" (precharged). The minimum time interval between successive ACTIVE commands to the same bank is defined by tRC. A subsequent ACTIVE command to another bank can be issued while the first bank is being accessed, which results in a reduction of total row-access overhead. The minimum time interval between successive ACTIVE commands to different banks is defined by tRRD. Figure 12 ACTIVE Command CLK Command A0-A12 BA0, BA1 ACT ROW BA x NOP ACT ROW BA y NOP NOP RD/WR COL BA y NOP tRRD tRCD = Don't Care Figure 13 Table 9 Parameter Bank Activate Timings Timing Parameters for Mode Register Set Command Symbol min. tRC tRCD tRRD 67 19 15 - 7.5 max. -- -- -- ns ns ns 1) 1) 1) Unit Notes ACTIVE to ACTIVE command period ACTIVE to READ or WRITE delay ACTIVE bank A to ACTIVE bank B delay 1) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period ; round up to next integer. Data Sheet 21 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4.5 READ CLK CKE CS RAS CAS WE A0-A8 A10 BA0,BA1 CA Enable AP (High) Subsequent to programming the mode register with CAS latency and burst length, READ bursts are initiated with a READ command, as shown in Figure 14. Basic timings for the DQs are shown in figure Figure 15; they apply to all read operations and therefore are omitted from all subsequent timing diagrams. In order to prevent bus contention on the DQs, care must be taken that a READ issued to one chip does not interfere with a READ or WRITE being in progress in the other chip of this stacked configuration. AP Disable AP BA = Don't Care BA = Bank Address CA = Column Address AP = Auto Precharge Figure 14 READ Command CLK tDQZ DQM tAC tLZ DQ tAC tOH DO n tHZ tOH DO n+1 = Don't Care Figure 15 Basic READ Timing Parameters for DQs Data Sheet 22 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description Table 10 Parameter Timing Parameters for READ Symbol - 7.5 min. max. 6.0 8.0 -- 7.0 -- 2 -- -- 100k -- ns ns ns ns ns 1) 1) Unit Notes Access time from CLK VDDQ = 2.3V .. 3.6V VDDQ = 1.65V .. 1.95V tAC tAC -- -- 1.0 3.0 3.0 -- 67 19 45 19 DQ low-impedance time from CLK DQ high-impedance time from CLK Data out hold time DQM to DQ High-Z delay (READ Commands) ACTIVE to ACTIVE command period ACTIVE to READ or WRITE delay ACTIVE to PRECHARGE command period PRECHARGE command period 1) tAC depends on VDDQ range; no dependency on CAS latency setting tLZ tHZ tOH tDQZ tRC tRCD tRAS tRP tCK ns ns ns ns 2) 2) 2) 2) 2) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period ; round up to next integer. The starting column and bank addresses are provided with the READ command and Auto Precharge is either enabled or disabled for that burst access. If Auto Precharge is enabled, the row being accessed starts precharge at the completion of the burst, provided tRAS has been satisfied. For the generic READ commands used in the following illustrations, Auto Precharge is disabled. During READ bursts, the valid data-out element from the starting column address is available following the CAS latency after the READ command. Each subsequent data-out element is valid nominally at the next positive clock edge. Upon completion of a READ burst, assuming no other READ command has been initiated, the DQs go to High-Z state. Figure 16 and Figure 17 show single READ bursts for each supported CAS latency setting. CLK tRCD tRAS READ Ba A, Col n Pre All Dis AP AP Pre Bank A NOP tRC NOP NOP PRE tRP NOP ACT Ba A, Row b Row b Command Address A10 (AP) ACT Ba A, Row x Row x NOP CL=2 DQ DO n DO n+1 DO n+2 DO n+3 Ba A, Col n = bank A, column n AP = Auto Precharge DO n = Data Out from column n Dis AP = Disable Auto Precharge Burst Length = 4 in the case shown. 3 subsequent elements of Data Out are provided in the programmed order following DO n. = Don't Care Figure 16 Single READ Burst (CAS Latency = 2) Data Sheet 23 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK tRCD tRAS NOP READ Ba A, Col n Pre All Dis AP AP NOP tRC NOP NOP PRE NOP tRP NOP ACT Ba A, Row b Row b Command Address A10 (AP) ACT Ba A, Row x Row x NOP CL=3 DQ Pre Bank A DO n DO n+1 DO n+2 DO n+3 Ba A, Col n = bank A, column n AP = Auto Precharge DO n = Data Out from column n Dis AP = Disable Auto Precharge Burst Length = 4 in the case shown. 3 subsequent elements of Data Out are provided in the programmed order following DO n. = Don't Care Figure 17 Single READ Burst (CAS Latency = 3) Data from any READ burst may be concatenated with data from a subsequent READ command. In either case, a continuous flow of data can be maintained. A READ command can be initiated on any clock cycle following a previous READ command, and may be performed to the same or a different (active) bank. The first data element from the new burst follows either the last element of a completed burst (Figure 18) or the last desired data element of a longer burst which is being truncated (Figure 19). The new READ command should be issued x cycles after the first READ command, where x equals the number of desired data elements. Please note that truncation of a READ burst by a subsequent READ or WRITE is only possible when both commands are issued to the same chip of this stacked configuration. CLK Command Address READ Ba A, Col n NOP NOP NOP READ Ba A, Col b NOP NOP NOP NOP CL=2 DQ CL=3 DQ DO n DO n+1 DO n+2 DO n+3 DO b DO b+1 DO n DO n+1 DO n+2 DO n+3 DO b DO b+1 DO b+2 Ba A, Col n (b) = Bank A, Column n (b) DO n (b) = Data Out from column n (b) Burst Length = 4 in the case shown. 3 subsequent elements of Data Out are provided in the programmed order following DO n (b). = Don't Care Figure 18 Consecutive READ Bursts Data Sheet 24 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK Command Address READ Ba A, Col n READ Ba A, Col a READ Ba A, Col x READ Ba A, Col m NOP NOP NOP NOP NOP CL=2 DQ CL=3 DQ DO n DO a DO x DO m DO m+1 DO m+2 DO n DO a DO x DO m DO m+1 DO m+2 DO m+3 Ba A, Col n etc. = Bank A, Column n etc. DO n etc. = Data Out from column n etc. Burst Length = 4 in the case shown; bursts are terminated by consecutive READ commands 3 subsequent elements of Data Out are provided in the programmed order following DO m. = Don't Care Figure 19 Random READ Bursts Non-consecutive READ bursts are shown in Figure 20. CLK Command Address READ Ba A, Col n NOP NOP NOP NOP READ Ba A, Col b NOP NOP NOP CL=2 DQ CL=3 DQ DO n DO n+1 DO n+2 DO n+3 DO b DO n DO n+1 DO n+2 DO n+3 DO b DO b+1 Ba A, Col n (b) = Bank A, Column n (b) DO n (b) = Data Out from column n (b) Burst Length = 4 in the case shown. 3 subsequent elements of Data Out are provided in the programmed order following DO n (b). = Don't Care Figure 20 Non-Consecutive READ Bursts Data Sheet 25 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4.5.1 READ Burst Termination Data from any READ burst may be truncated using the BURST TERMINATE command (see Page 35), provided that Auto Precharge was not activated. The BURST TERMINATE latency is equal to the CAS latency, i.e. the BURST TERMINATE command must be issued x clock cycles before the clock edge at which the last desired data element is valid, where x equals the CAS latency for READ bursts minus 1. This is shown in Figure 21. The BURST TERMINATE command may be used to terminate a full-page READ which does not self-terminate. CLK Command Address READ Ba A, Col n NOP NOP BST NOP NOP NOP NOP NOP CL=2 DQ CL=3 DQ DO n DO n+1 DO n+2 DO n DO n+1 DO n+2 Ba A, Col n = Bank A, Column n DO n = Data Out from column n Burst Length = 4 in the case shown. 2 subsequent elements of Data Out are provided in the programmed order following DO n. The burst is terminated after the 3rd data element. = Don't Care Figure 21 Terminating a READ Burst 3.4.5.2 Clock Suspend Mode for READ Cycles Clock suspend mode allows to extend any read burst in progress by a variable number of clock cycles. As long as CKE is registered LOW, the following internal clock pulse(s) will be ignored and data on DQ will remain driven, as shown in Figure 22. CLK CKE internal clock Command Address READ Ba A, Col n NOP NOP NOP NOP NOP tCSL DQ DO n DO n+1 tCSL tCSL DO n+1 DO n+2 Ba A, Col n etc. = Bank A, Column n etc. DO n etc. = Data Out from column n etc. CL = 2 in the case shown Clock suspend latency tCSL is 1 clock cycle = Don't Care Figure 22 Clock Suspend Mode for READ Bursts Data Sheet 26 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4.5.3 READ - DQM Operation DQM may be used to suppress read data and place the output buffers into High-Z state. The generic timing parameters as listed in Table 10 also apply to this DQM operation. The read burst in progress is not affected and will continue as programmed. CLK Command Address DQM DQ READ Ba A, Col n NOP NOP NOP NOP NOP NOP NOP tDQZ DO n DO n+2 DO n+3 Ba A, Col n = bank A, column n DO n = Data Out from column n CL = 2 in the case shown. DQM read latency tDQZ is 2 clock cycles = Don't Care Figure 23 READ Burst - DQM Operation 3.4.5.4 READ to WRITE A READ burst may be followed by or truncated with a WRITE command. The WRITE command can be performed to the same or a different (active) bank. Care must be taken to avoid bus contention on the DQs; therefore it is recommended that the DQs are held in High-Z state for a minimum of 1 clock cycle. This can be achieved by either delaying the WRITE command, or suppressing the data-out from the READ by pulling DQM HIGH two clock cycles prior to the WRITE command, as shown in Figure 24. With the registration of the WRITE command, DQM acts as a write mask: when asserted HIGH, input data will be masked and no write will be performed. Please note that truncation of a READ burst by a subsequent READ or WRITE is only possible when both commands are issued to the same chip of this stacked configuration. Data Sheet 27 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK Command Address DQM CL=2 DQ CL=3 DQ DO n High-Z READ Ba A, Col n NOP NOP NOP NOP WRITE Ba A, Col b NOP NOP DO n DO n+1 High-Z DI b DI b+1 DI b+2 DI b DI b+1 DI b+2 = Don't Care Ba A, Col n (b) = bank A, column n (b) DO n = Data Out from column n; DI b = Data In to column b; DQM is asserted HIGH to set DQs to High-Z state for 1 clock cycle prior to the WRITE command. Figure 24 READ to WRITE Timing 3.4.5.5 READ to PRECHARGE A READ burst may be followed by, or truncated with a PRECHARGE command to the same bank (provided that Auto Precharge was not activated), as shown in Figure 25. The PRECHARGE command should be issued x clock cycles before the clock edge at which the last desired data element is valid, where x equals the CAS latency for READ bursts minus 1. Following the PRECHARGE command, a subsequent ACTIVE command to the same bank cannot be issued until tRP is met. Please note that part of the row precharge time is hidden during the access of the last data elements. In the case of a READ being executed to completion, a PRECHARGE command issued at the optimum time (as described above) provides the same operation that would result from the same READ burst with Auto Precharge enabled. The disadvantage of the PRECHARGE command is that it requires that the command and address busses be available at the appropriate time to issue the command. The advantage of the PRECHARGE command is that it can be used to truncate bursts. CLK tRP Command Address A10 (AP) DQ READ Ba A, Col n Dis AP NOP NOP NOP PRE Ba A Pre All AP Pre Bank A DO n DO n+1 DO n+2 DO n+3 NOP NOP ACT Ba A, Row a CL=3 = Don't Care Ba A, Col n = bank A, column n; BA Am Row = bank A, row x DO n = Data Out from column n Burst Length = 4 in the case shown. CAS latency = 3 in the case shown 3 subsequent elements of Data Out are provided in the programmed order following DO n. Figure 25 Data Sheet READ to PRECHARGE Timing 28 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4.6 WRITE CLK CKE CS RAS CAS WE A0-A8 A10 BA0,BA1 CA Enable AP WRITE bursts are initiated with a WRITE command, as shown in Figure 26. Basic timings for the DQs are shown in Figure 27; they apply to all write operations. (High) AP Disable AP BA = Don't Care BA = Bank Address CA = Column Address AP = Auto Precharge Figure 26 WRITE Command CLK tIS DQM tIS DQ DI n tIH tIH DI n+2 = Don't Care Figure 27 Basic WRITE Timing Parameters for DQs The starting column and bank addresses are provided with the WRITE command, and Auto Precharge is either enabled or disabled for that access. If Auto Precharge is enabled, the row being accessed is precharged at the completion of the write burst. For the generic WRITE commands used in the following illustrations, Auto Precharge is disabled. During WRITE bursts, the first valid data-in element is registered coincident with the WRITE command, and subsequent data elements are registered on each successive positive edge of CLK. Upon completion of a burst, assuming no other commands have been initiated, the DQs remain in High-Z state, and any additional input data is ignored. Figure 28 and Figure 29 show a single WRITE burst for each supported CAS latency setting. Data Sheet 29 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description Table 11 Parameter Timing Parameters for WRITE Symbol min. -7.5 max. -- -- -- -- -- 100k -- -- ns ns -- -- -- 1) 1) 1) 1) 1) Unit Notes DQ and DQM input setup time DQ and DQM input hold time DQM write mask latency ACTIVE to ACTIVE command period ACTIVE to READ or WRITE delay ACTIVE to PRECHARGE command period WRITE recovery time PRECHARGE command period tIS tIH tDQW tRC tRCD tRAS tWR tRP 1.5 0.8 0 67 19 45 14 19 tCK ns ns ns ns ns 1) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period; round up to next integer. CLK tRCD tRAS WRITE Ba A, Col n Pre All Dis AP DI n DI n+1 DI n+2 DI n+3 AP Pre Bank A NOP tWR tRC NOP NOP NOP PRE tRP NOP ACT Ba A, Row b Row b Command Address A10 (AP) DQ ACT Ba A, Row x Row x NOP Ba A, Col n = bank A, column n DI n = Data In to column n Burst Length = 4 in the case shown. 3 subsequent elements of Data In are provided in the programmed order following DI n. = Don't Care Figure 28 WRITE Burst (CAS Latency = 2) Data Sheet 30 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK tRCD tRAS NOP WRITE Ba A, Col n Pre All Dis AP DI n DI n+1 DI n+2 DI n+3 AP Pre Bank A NOP tWR tRC NOP NOP NOP PRE NOP tRP NOP ACT Ba A, Row b Row b Command ACT NOP Ba A, Address Row n A10 (AP) DQ Row x Ba A, Col n = bank A, column n DI n = Data In to column n Burst Length = 4 in the case shown. 3 subsequent elements of Data In are provided in the programmed order following DI n. = Don't Care Figure 29 WRITE Burst (CAS Latency = 3) Data for any WRITE burst may be concatenated with or truncated with a subsequent WRITE command. In either case, a continuous flow of input data can be maintained. A WRITE command can be issued on any positive edge of clock following the previous WRITE command. The first data element from the new burst is applied after either the last element of a completed burst (Figure 30) or the last desired data element of a longer burst which is being truncated (Figure 31). The new WRITE command should be issued x cycles after the first WRITE command, where x equals the number of desired data elements. Please note that truncation of a WRITE burst by a subsequent READ or WRITE is only possible when both commands are issued to the same chip of this stacked configuration. CLK Command Address DQ NOP WRITE Ba A, Col n DI n DI n+1 DI n+2 DI n+3 NOP NOP NOP WRITE Ba A, Col b DI b DI b+1 DI b+2 DI b+3 NOP NOP NOP Ba A, Col n (b) = Bank A, Column n (b) DI n (b) = Data In to column n (b) Burst Length = 4 in the case shown. 3 subsequent elements of Data In are provided in the programmed order following DI n (b). = Don't Care Figure 30 Consecutive WRITE Bursts Data Sheet 31 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK Command Address DQ NOP WRITE Ba A, Col n DI n WRITE Ba A, Col a DI a WRITE Ba A, Col x DI x WRITE Ba A, Col m DI m DI m+1 DI m+2 DI m+3 NOP NOP NOP NOP Ba A, Col n etc. = Bank A, Column n etc. DI n etc. = Data In to column n etc. Burst Length = 4 in the case shown; bursts are terminated by consecutive WRITE commands. 3 subsequent elements of Data In are provided in the programmed order following DI m . = Don't Care Figure 31 Random WRITE Bursts Non-consecutive WRITE bursts are shown in Figure 32 CLK Command Address DQ NOP WRITE Ba A, Col n DI n DI n+1 DI n+2 DI n+3 NOP NOP NOP NOP WRITE Ba A, Col b DI b DI b+1 DI b+2 NOP NOP Ba A, Col n (b) = Bank A, Column n (b) DI n (b) = Data In to column n (b) Burst Length = 4 in the case shown. 3 subsequent elements of Data In are provided in the programmed order following DI n (b). = Don't Care Figure 32 Non-Consecutive WRITE Bursts 3.4.6.1 WRITE Burst Termination Data from any WRITE burst may be truncated using the BURST TERMINATE command (see Page 35), provided that Auto Precharge was not activated. The input data provided coincident with the BURST TERMINATE command will be ignored. This is shown in Figure 33. The BURST TERMINATE command may be used to terminate a full-page WRITE which does not self-terminate. Data Sheet 32 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK Command Address DQ NOP WRITE Ba A, Col n DI n DI n+1 DI n+2 NOP NOP BST NOP NOP = Don't Care Ba A, Col n = Bank A, Column n DI n = Data In to column n Burst Length = 4 in the case shown. 2 subsequent elements of Data In are written in the programmed order following DI n. The burst is terminated after the 3rd data element. Figure 33 Terminating a WRITE Burs 3.4.6.2 Clock Suspend Mode for WRITE Cycles Clock suspend mode allows to extend any WRITE burst in progress by a variable number of clock cycles. As long as CKE is registered LOW, the following internal clock pulse(s) will be ignored and no data will be captured, as shown in Figure 34. CLK CKE internal clock Command Address NOP WRITE Ba A, Col n NOP NOP NOP tCSL DQ DI n DI n+1 tCSL tCSL DI n+2 Ba A, Col n etc. = Bank A, Column n etc. DO n etc. = Data Out from column n etc. CL = 2 in the case shown Clock suspend latency tCSL is 1 clock cycle = Don't Care Figure 34 Clock Suspend Mode for WRITE Bursts Data Sheet 33 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4.6.3 WRITE - DQM Operation DQM may be used to mask write data: when asserted HIGH, input data will be masked and no write will be performed. The generic timing parameters as listed in Table 11 also apply to this DQM operation. The write burst in progress is not affected and will continue as programmed. CLK Command Address DQM DQ DI n DI n+2 DI n+3 NOP WRITE Ba A, Col n NOP NOP NOP NOP = Don't Care Ba A, Col n = Bank A, Column n DI n = Data In to column n Burst Length = 4 in the case shown. 3 subsequent elements of Data In are provided in the programmed order following DI n, with the first element (DI n+1) being masked. DQM write latency is 0 clock cycles. Figure 35 WRITE Burst - DQM Operation 3.4.6.4 WRITE to READ A WRITE burst may be followed by, or truncated with a READ command. The READ command can be performed to the same or a different (active) bank. With the registration of the READ command, data inputs will be ignored and no WRITE will be performed, as shown in Figure 36. Please note that truncation of a WRITE burst by a subsequent READ or WRITE is only possible when both commands are issued to the same chip of this stacked configuration. CLK Command Address WRITE Ba A, Col n NOP NOP READ Ba A, Col b NOP NOP NOP NOP CL=2 DQ DI n DI n+1 DI n+2 High-Z DO b DO b+1 DO b+2 Write data are ignored DQ DI n DI n+1 DI n+2 CL=3 High-Z DO b DI b+1 Ba A, Col n (b) = bank A, column n (b) = Don't Care DI n = Data In to column n; DO b = Data Out from column b; Burst Length = 4 in the case shown. 3 subsequent elements of Data In (Out) are provided in the programmed order following DI n (DO b). DI n+3 is ignored due to READ command. No DQM masking required at this point. Figure 36 WRITE to READ Timing Data Sheet 34 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description WRITE to PRECHARGE A WRITE burst may be followed by, or truncated with a PRECHARGE command to the same bank (provided that Auto Precharge was not activated), as shown in Figure 37. The PRECHARGE command should be issued tWR after the clock edge at which the last desired data element of the WRITE burst was registered. Additionally, when truncating a WRITE burst, DQM must be pulled to mask input data presented during tWR prior to the PRECHARGE command. Following the PRE-CHARGE command, a subsequent ACTIVE command to the same bank cannot be issued until tRP is met. In the case of a WRITE being executed to completion, a PRECHARGE command issued at the optimum time (as described above) provides the same operation that would result from the same WRITE burst with Auto Precharge enabled. The disadvantage of the PRECHARGE command is that it requires that the command and address busses be available at the appropriate time to issue the command. The advantage of the PRECHARGE command is that it can be used to truncate bursts. CLK tWR Command Address A10 (AP) DQM DQ DI n DI n+1 DI n+2 NOP WRITE Ba A, Col n Dis AP NOP NOP NOP PRE Ba A Pre All AP Pre Bank A tRP NOP ACT Ba A, Row a Ba A, Col n = bank A, column n AP = Auto Precharge = Don't Care DI n = Data In to column n Dis AP = Disable Auto Precharge Burst Length = 4 in the case shown. 3 subsequent elements of Data In are provided in the programmed order following DI n. DI n+3 is masked due to DQM pulled HIGH during tWR period prior to PRECHARGE command. Figure 37 WRITE to PRECHARGE Timing 3.4.7 . BURST TERMINATE CLK CKE CS RAS CAS WE A0-A12 BA0,BA1 = Don't Care (High) The BURST TERMINATE command is used to truncate READ or WRITE bursts (with Auto Precharge disabled). The most recently registered READ or WRITE command prior to the BURST TERMINATE command will be truncated, as shown in Figure 21 and Figure 33, respectively Figure 38 BURST TERMINATE Command Data Sheet 35 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4.8 PRECHARGE CLK CKE CS RAS CAS WE A0-A9 A11,A12 All Banks (High) The PRECHARGE command is used to deactivate (close) the open row in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row access a specified time (tRP) after the PRECHARGE command is issued. Input A10 determines whether one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are treated as "Don't Care." Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank. A PRECHARGE command will be treated as a NOP if there is no open row in that bank, or if the previously open row is already in the process of precharging. A10 One Bank BA0,BA1 BA = Don't Care BA = Bank Address (if A10 = L, otherwise Don't Care) Figure 39 PRECHARGE Command 3.4.8.1 AUTO PRECHARGE Auto Precharge is a feature which performs the same individual-bank precharge functions described above, but without requiring an explicit command. This is accomplished by using A10 to enable Auto Precharge in conjunction with a specific READ or WRITE command. A precharge of the bank/row that is addressed with the READ or WRITE command is automatically performed upon completion of the READ or WRITE burst. Auto Precharge is nonpersistent in that it is either enabled or disabled for each individual READ or WRITE command. Auto Precharge ensures that the precharge is initiated at the earliest valid stage within a burst. The user must not issue another command to the same bank until the precharge (tRP) is completed. This is determined as if an explicit PRECHARGE command was issued at the earliest possible time, as described for each burst type. Table 12 Parameter ACTIVE to PRECHARGE command period WRITE recovery time PRECHARGE command period Timing Parameters for PRECHARGE Symbol min. - 7.5 max. 100k -- -- ns ns ns 1) 1) 1) Units Notes tRAS tWR tRP 45 14 19 1) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period; round up to next integer. Data Sheet 36 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.4.8.2 CONCURRENT AUTO PRECHARGE A READ or WRITE burst with Auto Precharge enabled can be interrupted by a subsequent READ or WRITE command issued to a different bank. Figure 40 shows a READ with Auto Precharge to bank n, interrupted by a READ (with or without Auto Precharge) to bank m. The READ to bank m will interrupt the READ to bank n, CAS latency later. The precharge to bank n will begin when the READ to bank m is registered. Figure 41 shows a READ with Auto Precharge to bank n, interrupted by a WRITE (with or without Auto Precharge) to bank m. The precharge to bank n will begin when the WRITE to bank m is registered. DQM should be pulled HIGH two clock cycles prior to the WRITE to prevent bus contention. Figure 42 shows a WRITE with Auto Precharge to bank n, interrupted by a READ (with or without Auto Precharge) to bank m. The precharge to bank n will begin tWR after the new command to bank m is registered. The last valid data-in to bank n is one clock cycle prior to the READ to bank m. Figure 43 shows a WRITE with Auto Precharge to bank n, interrupted by a WRITE (with or without Auto Precharge) to bank m. The precharge to bank n will begin tWR after the WRITE to bank m is registered. The last valid data-in to bank n is one clock cycle prior to the WRITE to bank m. CLK Command Address NOP RD-AP Bank n Col b NOP READ Bank m Col x NOP NOP NOP NOP CL=2 DQ DO b tRP (bank n) DO b+1 DO x DO x+1 DO x+2 RD-AP = Read with Auto Precharge; READ = Read with or without Auto Precharge CL = 2 and Burst Length = 4 in the case shown Read with Auto Precharge to bank n is interrupted by subsequent Read to bank m = Don't Care Figure 40 READ with Auto Precharge Interrupted by READ CLK Command Address DQM CL=2 DQ DO b DI x NOP RD-AP Bank n Col b NOP NOP WRITE Bank m Col x NOP NOP NOP tRP (bank n) DI x+1 DI x+2 DI x+3 RD-AP = Read with Auto Precharge; WRITE = Write with or without Auto Precharge CL = 2 and Burst Length = 4 in the case shown Read with Auto Precharge to bank n is interrupted by subsequent Write to bank m = Don't Care Figure 41 READ with Auto Precharge Interrupted by WRITE Data Sheet 37 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK Command Address WR-AP Bank n Col b NOP READ Bank m Col x NOP NOP NOP NOP NOP tWR (bank n) CL=2 DQ DO b DO b+1 DO x tRP (bank n) DO x+1 DO x+2 DO x+3 WR-AP = Write with Auto Precharge; READ = Read with or without Auto Precharge CL = 2 and Burst Length = 4 in the case shown Write with Auto Precharge to bank n is interrupted by subsequent Read to bank m = Don't Care Figure 42 WRITE with Auto Precharge Interrupted by READ CLK Command Address WR-AP Bank n Col b NOP WRITE Bank m Col x NOP NOP NOP NOP NOP tWR (bank n) DQ DI b DI b+1 DI x DI x+1 DI x+1 tRP (bank n) DI x+1 WR-AP = Write with Auto Precharge; WRITE = Write with or without Auto Precharge Burst Length = 4 in the case shown Write with Auto Precharge to bank n is interrupted by subsequent Write to bank m = Don't Care Figure 43 WRITE with Auto Precharge Interrupted by WRITE 3.4.9 AUTO REFRESH and SELF REFRESH The Mobile-RAM requires a refresh of all rows in a rolling interval. Each refresh is generated in one of two ways: by an explicit AUTO REFRESH command, or by an internally timed event in SELF REFRESH mode. 3.4.9.1 AUTO REFRESH CLK CKE CS RAS CAS WE A0-A12 BA0,BA1 = Don't Care (High) Auto Refresh is used during normal operation of the Mobile-RAM. The command is nonpersistent, so it must be issued each time a refresh is required. A minimum row cycle time (tRC) is required between two AUTO REFRESH commands. The same rule applies to any access command after the auto refresh operation. All banks must be precharged prior to the AUTO REFRESH command. The refresh addressing is generated by the internal refresh controller. This makes the address bits "Don't Care" during an AUTO REFRESH command. The Mobile-RAM requires AUTO REFRESH cycles at an average periodic interval of 7.8 s (max.). Partial array mode has no influence on auto refresh mode. Figure 44 AUTO REFRESH Command Data Sheet 38 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK tRP Command Address A10 (AP) DQ Pre All High-Z tRC ARF NOP NOP ARF tRC NOP NOP ACT Ba A, Row n Row n PRE NOP Ba A, Row n = bank A, row n = Don't Care Figure 45 AUTO REFRESH 3.4.9.2 SELF REFRESH CLK CKE CS RAS CAS WE A0-A12 BA0,BA1 = Don't Care The SELF REFRESH command can be used to retain data in the Mobile-RAM, even if the rest of the system is powered down. When in the SELF REFRESH mode, the Mobile-RAM retains data without external clocking. The SELF REFRESH command is initiated like an AUTO REFRESH command except CKE is LOW. Input signals except CKE and CLK are "Don't Care" during SELF REFRESH. CLK pin may not float. The SELF REFRESH command may be issued to both chips at the same time (CS0 = CS1 = 0). The procedure for exiting SELF REFRESH requires a stable clock prior to CKE returning HIGH. Once CKE is HIGH, NOP commands must be issued for tRC because time is required for a completion of any internal refresh in progress. The use of SELF REFRESH mode introduces the possibility that an internally timed event can be missed when CKE is raised for exit from SELF REFRESH mode. Upon exit from SELF REFRESH an extra AUTO REFRESH command is recommended. Figure 46 SELF REFRESH Entry Command Data Sheet 39 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK tRP CKE Command Address A10 (AP) DQ Pre All High-Z > tRC tSREX tRC tRC PRE NOP ARF NOP NOP NOP ARF NOP ACT Ba A, Row n Row n Self Refresh Entry Command Self Refresh Exit Command Exit from Self Refresh Any Command (Auto Refresh Recommended) = Don't Care Figure 47 Table 13 Parameter SELF REFRESH Entry and Exit Timing Parameters for AUTO REFRESH and SELF REFRESH Symbol min. - 7.5 max. -- -- 64 -- ns ns ms 1) 1) 1) 1) Units Notes ACTIVE to ACTIVE command period PRECHARGE command period Refresh period (8192 rows) Self refresh exit time tRC tRP tREF tSREX 67 19 -- 1 tCK 1) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period; round up to next integer. 3.4.10 POWER DOWN CLK CKE CS RAS CAS WE A0-A12 BA0,BA1 = Don't Care Power-down is entered when CKE is registered LOW (no accesses can be in progress). If power-down occurs when all banks are idle, this mode is referred to as precharge power-down; if power-down occurs when there is a row active in any bank, this mode is referred to as active power-down. Entering power-down deactivates the input and output buffers, excluding CKE and CLK. In power-down mode, CKE LOW must be maintained, and all other input signals are "Don't Care". However, power-down duration is limited by the refresh requirements of the device (tREF). The power-down state is synchronously exited when CKE is registered HIGH (along with a NOP or DESELECT command). One clock delay is required for power down entry and exit. Power-down entry and exit is common to both stacked chips as they share a common CKE signal. 40 Rev. 1.3, 2004-04 10212003-BSPE-77OL Figure 48 POWER DOWN Entry Command Data Sheet HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description CLK tRP CKE Command Address A10 (AP) DQ Pre All High-Z PRE NOP NOP NOP Valid Valid Valid Power Down Entry Exit from Power Down Any Command = Don't Care Precharge Power Down mode shown: all banks are idle and tRP met when Power Down Entry Command is issued Figure 49 POWER DOWN Entry and Exit 3.4.10.1 DEEP POWER DOWN The deep power down mode is an unique function on Low Power SDRAM devices with extremly low current consumption. Deep power down mode is entered using the BURST TERMINATE command (cf. Figure 38) except that CKE is LOW. All internal voltage generators inside the device are stopped and all memory data is lost in this mode. To enter the deep power down mode all banks must be precharged. The deep power down mode is asynchronously exited by asserting CKE HIGH. After the exit, the same command sequence as for power-up initialization has to be applied before any other command may be issued (cf. Figure 4 and Figure 7). Data Sheet 41 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3.5 Table 14 Any Idle Function Truth Tables Current State Bank n - Command to Bank n CS H L L L L L RAS CAS WE Command / Action X H L L L L H H L H H L H H H L H X H H L L H L L H L L H H L L H H X H H H L L H L L H L L L H L L L DESELECT (NOP / continue previous operation) NO OPERATION (NOP / continue previous operation) ACTIVE (select and activate row) AUTO REFRESH MODE REGISTER SET PRECHARGE READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) READ (select column and start new READ burst) WRITE (select column and start new WRITE burst) PRECHARGE (truncate READ burst, start precharge) BURST TERMINATE READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (truncate WRITE burst, start precharge) BURST TERMINATE Notes 1)2)3)4)5)6) 1) to 6) 1) to 6) 1) to 7) 1) to 7) 1) to 6), 8) 1) to 6), 9) 1) to 6), 9) 1) to 6), 10) 1) to 6), 9) 1) to 6), 9) 1) to 6), 10) 1) to 6), 11) 1) to 6), 9) 1) to 6), 9) 1) to 6), 10) 1) to 6), 11) Current State Row Active L L L Read (AutoPrecharge Disabled) Write (AutoPrecharge Disabled) L L L L L L L L 1) This table applies when CKEn-1 was HIGH and CKEn is HIGH and after tRC has been met (if the previous state was self refresh). 2) This table is bank-specific, except where noted, i.e., the current state is for a specific bank and the commands shown are those allowed to be issued to that bank when in that state. Exceptions are covered in the notes below. 3) Current state definitions: Idle: The bank has been precharged, and tRP has been met. Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are in progress. Read: A READ burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated. Write: A WRITE burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated. 4) The following states must not be interrupted by a command issued to the same bank. DESELECT or NOP commands, or allowable commands to the other bank should be issued on any clock edge occurring during these states. Allowable commands to the other bank are determined by its current state and according to Table 15. Precharging: Starts with registration of a PRECHARGE command and ends when tRP is met. Once tRP is met, the bank is in the "idle" state. Row Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the bank is in the "row active" state. Read with AP Enabled: Starts with registration of a READ command with Auto Precharge enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state. Write with AP Enabled: Starts with registration of a WRITE command with Auto Precharge enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state. Data Sheet 42 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 5) The following states must not be interrupted by any executable command; DESELECT or NOP commands must be applied on each positive clock edge during these states. Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRC is met. Once tRC is met, the SDRAM is in the "all banks idle" state. Accessing Mode Register: Starts with registration of a MODE REGISTER SET command and ends when tMRD has been met. Once tMRD is met, the SDRAM is in the "all banks idle" state. Precharging All: Starts with registration of a PRECHARGE ALL command and ends when tRP is met. Once tRP is met, all banks are in the idle state. 6) All states and sequences not shown are illegal or reserved. 7) Not bank-specific; requires that all banks are idle and no bursts are in progress. 8) Same as NOP command in that state. 9) READs or WRITEs listed in the Command/Action column include READs or WRITEs with Auto Precharge enabled and READs or WRITEs with Auto Precharge disabled. 10) May or may not be bank-specific; if multiple banks are to be precharged, each must be in a valid state for precharging. 11) Not bank-specific; BURST TERMINATE affects the most recent READ or WRITE burst, regardless of bank. Table 15 Any Idle Current State Bank n - Command to Bank m (different bank) CS H L X L L L L L L L L L L L L L L L L L L L L RAS CAS WE Command / Action X H X L H H L L H H L L H H L L H H L L H H L X H X H L L H H L L H H L L H H L L H H L L H X H X H H L L H H L L H H L L H H L L H H L L DESELECT (NOP / continue previous operation) NO OPERATION (NOP / continue previous operation) Any command otherwise allowed to bank n ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) Notes 1)2)3)4)5)6) 1) to 6) 1) to 6) 1) to 6) 1) to 7) 1) to 7) 1) to 6) 1) to 6) 1) to 7) 1) to 8) 1) to 6) 1) to 6) 1) to 7) 1) to 7) 1) to 6) 1) to 6) 1) to 7), 9) 1) to 9) 1) to 6) 1) to 6) 1) to 7), 9) 1) to 7), 9) 1) to 6) Current State Row Activating, Active, or Precharging Read (AutoPrecharge Disabled) Write (AutoPrecharge Disabled) Read (with AutoPrecharge) Write (with AutoPrecharge) 1) This table applies when CKEn-1 was HIGH and CKEn is HIGH and after tRC has been met (if the previous state was Self Refresh). 2) This table describes alternate bank operation, except where noted, i.e., the current state is for bank n and the commands shown are those allowed to be issued to bank m (assuming that bank m is in such a state that the given command is allowable). Exceptions are covered in the notes below. Data Sheet 43 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Functional Description 3) Current state definitions: Idle: The bank has been precharged, and tRP has been met. Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are in progress. Read: A READ burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated. Write: A WRITE burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated. Read with AP Enabled: Starts with registration of a READ command with Auto Precharge enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state. Write with AP Enabled: Starts with registration of a WRITE command with Auto Precharge enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state. 4) AUTO REFRESH, SELF REFRESH and MODE REGISTER SET commands may only be issued when all banks are idle. 5) A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state only. 6) All states and sequences not shown are illegal or reserved. 7) READs or WRITEs listed in the Command/Action column include READs or WRITEs with Auto Precharge enabled and READs or WRITEs with Auto Precharge disabled. 8) Requires appropriate DQM masking. 9) Concurrent Auto Precharge: bank n will start precharging when its burst has been interrupted by a READ or WRITE command to bank m. Table 16 CKEn-1 L L Truth Table - CKE CKEn Current State Power Down Self Refresh Clock Suspend Deep Power Down Command X X X X DESELECT or NOP DESELECT or NOP X X DESELECT or NOP DESELECT or NOP AUTO REFRESH BURST STOP (valid) Action Maintain Power Down Maintain Self Refresh Maintain Clock Suspend Maintain Deep Power Down Exit Power Down Exit Self Refresh Exit Clock Suspend Exit Deep Power Down Enter Precharge Power Down Enter Active Power Down Enter Self Refresh Enter Deep Power Down Enter Clock Suspend Notes 1)2)3)4) 1) to 4) 1) to 4) 1) to 4) 1) to 4) 1) to 5) 1) to 4) 1) to 4) 1) to 4) 1) to 4) 1) to 4) 1) to 4) 1) to 4) 1) to 4) L H Power Down Self Refresh Clock Suspend Deep Power Down H L All Banks Idle Bank(s) Active All Banks Idle All Banks Idle Read / Write burst H H see Table 14 and Table 15 1) CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge. 2) Current state is the state immediately prior to clock edge n. 3) COMMAND n is the command registered at clock edge n; ACTION n is a result of COMMAND n. 4) All states and sequences not shown are illegal or reserved. 5) DESELECT or NOP commands should be issued on any clock edges occurring during tRC period. Data Sheet 44 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Electrical Characteristics 4 4.1 Table 17 Parameter Electrical Characteristics Absolute Maximum Ratings Absolute Maximum Ratings Symbol Values min. max. 4.6 4.6 V V V V C C C W mA -1.0 -1.0 -1.0 -1.0 0 -25 -55 -- -- Unit Power Supply Voltage Power Supply Voltage for Output Buffer Input Voltage Output Voltage Operation Case Temperature Storage Temperature Power Dissipation Short Circuit Output Current Commercial Extended VDD VDDQ VIN VOUT TC TC TSTG PD IOUT VDDQ + 0.5 VDDQ + 0.5 +70 +85 +150 0.7 50 Attention: Stresses above those listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. 4.2 Table 18 Parameter DC Operation Conditions DC Characteristics1) Symbol Values min. max. 3.6 1.95 or 3.60 V V - 2) Unit Notes Power Supply Voltage Power Supply Voltage for DQ Output Buffer VDD VDDQ 2.3 1.65 or 2.30 0.8 x VDDQ -0.3 Input high voltage Input low voltage Output high voltage Output low voltage Input leakage current Output leakage current VIH VIL VOH VOL IIL IOL VDDQ + 0.3 0.3 -- 0.2 5 5 V V V V A A 3) 3) VDDQ - 0.2 -- -5 -5 - - - - 1) 0 C TC 70 C (comm.); All voltages referenced to VSS. VSS and VSSQ must be at same potential. 2) Device is characterized for both ranges of VDDQ; VDDQ < VDD +0.3 3) VIH may overshoot to VDD + 0.8 V for pulse width < 4 ns; VIL may undershoot to -0.8 V for pulse width < 4 ns. Pulse width measured at 50% with amplitude measured between peak voltage and DC reference level. Data Sheet 45 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Electrical Characteristics 4.3 Table 19 Parameter Pin Capacitances Pin Capacitances1)2) Symbol Values min. max. 7.0 5.0 7.0 10.0 pF pF pF pF 5.0 3.0 5.0 7.0 Unit Input capacitance: CLK Input capacitance: CS0, CS1 Input capacitance: all other input pins Input/Output capacitance: DQ CI1 CI2 CI3 CIO 1) These values are not subject to production test but verified by device characterization. 2) Input capacitance is measured according to JEP147 with VDD, VDDQ applied and all other pins (except the pin under test) floating. DQ's should be in high impedance state. This may be achieved by pulling CKE to low level. Data Sheet 46 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Electrical Characteristics 4.4 Table 20 Parameter AC Characteristics AC Characteristics1) Symbol min. VDDQ = 2.3V .. 3.6V VDDQ = 1.65V .. 1.95V CL = 3 CL = 2 CL = 2 or 3 CL = 3 CL = 2 or 3 CL = 2 or 3 tAC tCH tCL tIS tIH tMRD tLZ tHZ tOH tDQZ tDQW tRC tRCD tRRD tRAS tWR tRP tREF tSREX fCK tCK 7.5 9.5 9.5 -- -- 6.0 8.0 2.5 2.5 1.5 0.8 2 1.0 3.0 3.0 -- 0 67 19 15 45 14 19 -- 1 - 7.5 max. -- -- -- 133 105 -- -- -- -- -- -- -- -- 7.0 -- 2 -- -- -- -- 100k -- -- 64 -- ns ns ns MHz ns ns ns ns ns ns tCK ns ns ns tCK tCK ns ns ns ns ns ns ms -- 2)3) Unit Notes -- -- -- Clock cycle time Clock frequency Access time from CLK Clock high-level width Clock low-level width VDDQ = 2.3V .. 3.6V VDDQ = 1.65V .. 1.95V VDDQ = 2.3V .. 3.6V VDDQ = 1.65V .. 1.95V MHz -- -- -- -- 4) 4) Address, data and command input setup time Address, data and command input hold time MODE REGISTER SET command period DQ low-impedance time from CLK DQ high-impedance time from CLK Data out hold time DQM to DQ High-Z delay (READ Commands) DQM write mask latency ACTIVE to ACTIVE command period ACTIVE to READ or WRITE delay ACTIVE bank A to ACTIVE bank B delay ACTIVE to PRECHARGE command period WRITE recovery time PRECHARGE command period Refresh period (8192 rows) Self refresh exit time -- -- -- 2)5) -- -- 5) 5) 5) 5) 6) 5) -- -- 1) 0 C TC 70 C (comm.); VDD = 2.3V .. 3.6V; VDDQ = 1.8 V 0.15 V; or 2.3V .. 3.6V; All parameters assumes proper device initialization. AC timing tests measured at 0.9 V. The transition time is measured between VIH and VIL; all AC characteristics assume tT = 1 ns. 2) Specified tAC and tOH parameters are measured with a 30 pF capacitive load only as shown below: I/O 30 pF 3) If tT(CLK) > 1 ns, a value of (tT/2 - 0.5) ns has to be added to this parameter. 4) If tT > 1 ns, a value of (tT - 1) ns has to be added to this parameter. 5) These parameter account for the number of clock cycles and depend on the operating frequency, as follows: no. of clock cycles = specified delay / clock period; round up to next integer. 6) The write recovery time of tWR = 14 ns allows the use of one clock cycle for the write recovery time when fCK 72 MHz. With fCK > 72 MHz two clock cycles for tWR are mandatory. Infineon Technologies recommends to use two clock cycles for the write recovery time in all applications.. Data Sheet 47 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Electrical Characteristics 4.5 Table 21 Operating Currents Maximum Operating Currents1) Symbol Values - 7.5 85 1.2 40 Unit mA mA mA Notes 2)3) Parameter & Test Conditions Operating Current: one bank: active / read / precharge, tRC = tRCmin Precharge Standby Current in Power-Down Mode: all banks idle, CS VIHmin, CKE VILmax Precharge Standby Current in Non-Power Down Mode: all banks idle, CS VIHmin, CKE VIHmin, inputs changing once per clock cycle Active Standby Current in Power Down Mode: one bank active, CS VIHmin, CKE VILmax, inputs changing once per clock cycle Active Standby Current in Non-Power Down Mode: one bank active, CS VIHmin, CKE VIHmin, inputs changing once per clock cycle Operating Current for Burst Mode: all banks active; continuous burst read, inputs changing once per 2 clock cycles Auto-Refresh Current: tRC = tRCmin, "burst refresh" Deep Power Down Mode current ICC1 ICC2P ICC2N 2) 2) ICC3P 7 mA 2) ICC3N 50 mA 2) ICC4 100 mA 2)3) ICC5 ICC7 175 10 mA A 2) - 1) 0 C TC 70 C (comm.); VDD = 2.3V .. 3.6V; VDDQ = 1.8 V 0.15 V; or 2.3V .. 3.6V; Recommended Operating Conditions unless otherwise noted 2) These values are measured with tCK = 7.5 ns for - 7.5 parts. 3) All parameters measured with no output loads. Table 22 Self Refresh Currents1) Max. Temperature Symbol Values max. 1600 1100 900 750 Units Notes A 2) Parameter & Test Conditions Self Refresh Current: 85 C Self refresh mode, CKE = 0.2 V, clock off, 70 C full array activation (PASR = 000) 45 C 15 C Self Refresh Current: 85 C Self refresh mode, CKE = 0.2 V, clock off, 70 C half array activation (PASR = 001) 45 C 15 C Self Refresh Current: 85 C Self refresh mode, CKE = 0.2 V, clock off, 70 C quarter array activation (PASR = 010) 45 C 15 C 2) Target values, to be verified on final product. ICC6 ICC6 1150 900 800 700 A 2) ICC6 900 800 750 675 A 2) 1) 0 C TC 70 C (comm.); VDD = 2.3V .. 3.6V; VDDQ = 1.8 V 0.15 V; or 2.3V .. 3.6V; Data Sheet 48 Rev. 1.3, 2004-04 10212003-BSPE-77OL HYB25L512160AC-7.5 512MBit Mobile-RAM Package Outline 5 Package Outline 8.00 0.10 P-TFBGA-54-2 JEDEC MO207G Var. DE compatible All Dimensions in mm BALL A1 INDICATOR 12.00 0.10 TOP VIEW 1.40 MAX O0.40 0.80 0.10 C 0.80 0.12 C BOTTOM VIEW Figure 50 Package FBGA-54 Data Sheet 49 Rev. 1.3, 2004-04 10212003-BSPE-77OL www.infineon.com Published by Infineon Technologies AG |
Price & Availability of HYB25L512160AC-75 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |