 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PCM-5862E/EL All in one multi-media Pentium processor-based single board computer with audio, SVGA, Ethernet and PCI expansion slot. User's Manual for PCM-5862E/EL Copyright Notice This document is copyrighted, 1997. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, or for any infringements upon the rights of third parties that may result from its use. Acknowledgements AMD is a trademark of Advanced Micro Devices, Inc. Award is a trademark of Award Software International, Inc. C&T is a trademark of Chips and Technologies, Inc. Cyrix is a trademark of Cyrix Corporation. IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Corporation. Intel and Pentium are trademarks of Intel Corporation. Microsoft Windows (R) is a registered trademark of Microsoft Corp. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. SiS is a trademark of Silicon Integration Systems Corporation SMC is a trademark of Standard Microsystems Corporation. UMC is a trademark of United Microelectronics Corporation. VIA is a trademark of VIA Technology, Inc. IDT is a trademark of Intergrated Device Technology , Inc. All other product names or trademarks are properties of their respective owners. Part No. 2006586201 1st Edition Printed in Taiwan Sept 1998 Packing list Before you begin installing your card, please make sure that the following materials have been shipped: *1 *1 *2 *1 PCM-5862E/5862EL All-in-One Single Board Computer Ethernet driver disk utility disks with PCI SVGA utility programs and drivers for Windows 3.1, Windows 95, Windows NT 4.0, and OS/2 audio driver disks for Windows 3.1, Windows 95, and DOS utility program. (PCM-5862E only) If any of these items are missing or damaged, contact your distributor or sales representative immediately. Please refer to page 98 for the optional interface wiring kit. Contents Chapter 1 General Information .....................1 Introduction .............................................................................................. 2 Highly integrated multi-media SBC ................................................ 2 Features ..................................................................................................... 3 Specifications ............................................................................................ 3 Standard SBC functions .................................................................. 3 PCI SVGA/flat panel interface: ...................................................... 4 Audio function: (PCM-5862E only) ............................................... 4 PCI Bus Ethernet Interface: ............................................................ 5 Mechanical and environmental ....................................................... 5 Board layout and dimensions .................................................................. 5 Chapter 2 Installation .....................................7 Jumpers ..................................................................................................... 8 Connectors ................................................................................................ 9 Locating jumpers .................................................................................... 10 Locating connectors ................................................................................ 11 CPU installation and upgrading ............................................................ 13 Install a CPU in the ZIF socket ..................................................... 13 System clock setting (J1, J2, and J4) ............................................ 14 CPU Speed Reference Table ........................................................ 14 System/PCI clock setting ............................................................. 15 CPU frequency ratio ..................................................................... 15 Pentium MMX(P55C) enabled/disabled (JP2) ............................ 15 CPU voltage setting (JP1) ............................................................. 16 M1 cache linear mode setting (J5) ................................................ 16 CMOS clear (J6) ........................................................................... 17 Buzzer enabled/disabled (J7) ....................................................... 17 Installing DRAM (SIMMs) ................................................................... 17 Installing SIMMs .......................................................................... 17 IDE hard drive connector (CN17) ........................................................ 18 Connecting the hard drive ............................................................. 18 Floppy drive connector (CN18) ............................................................. 19 Connecting the floppy drive .......................................................... 19 Parallel port connector (CN19) ............................................................. 20 Keyboard and PS/2 mouse connector (CN15) ...................................... 20 Front panel connector (CN7) ................................................................. 20 Speaker ......................................................................................... 21 LED interface ............................................................................... 21 Watchdog output ........................................................................... 21 Reset switch .................................................................................. 21 Power connectors (CN6, CN10, CN14) ................................................ 21 Peripheral power connector, -5V, -12V (CN10) ........................... 21 Main power connector, +5V, +12V (CN14) ................................. 21 Fan power supply connector (CN6) .............................................. 21 ATX Power Control Connector (CON1, CON2) ................................. 22 ATX feature connector (CON1) and soft power switch connector (CON2) ........................................... 22 IR connector (CN12) .............................................................................. 23 Audio interfaces (CN8, CN13) .............................................................. 23 Audio connector (CN13) ............................................................... 23 CD audio input connector (CN8) .................................................. 23 Audio power source setting (J16) ................................................. 24 Audio power source setting ..................................................................... 24 COM-port connector (CN16) ................................................................ 25 COM2 RS-232/422/485 setting (J14, J15) ................................... 25 COM3/COM4 RI pin setting (J11, J12) ........................................ 26 VGA interface connections .................................................................... 27 CRT display connector (CN1) ....................................................... 27 Flat panel display connector (CN2) .............................................. 27 LCD power setting (J10) ............................................................... 28 Ethernet configuration ........................................................................... 29 100BASE-T connector (CN11) ..................................................... 29 Network boot ................................................................................. 29 Watchdog timer configuration .............................................................. 30 Watchdog timer action (J13) ......................................................... 30 USB connectors (CN4, CN5) ................................................................. 31 Chapter 3 Software Configuration ..............33 Introduction ............................................................................................ 34 Connections for five standard LCDs .................................................... 34 Connections to Sharp LM64183P, LM64P89 ............................... 34 Connections to PLANAR EL ........................................................ 35 Connections to Toshiba LTM10C042 ........................................... 36 Connections to Sharp LM64C142 ................................................ 37 Connections to Toshiba LTM12C275A ........................................ 38 Ethernet software configuration ........................................................... 39 System test and initialization ................................................................. 40 System configuration verification ................................................. 40 Chapter 4 Award BIOS Setup ......................41 System test and initialization ................................................................. 42 System configuration verification ................................................. 42 AWARD BIOS setup .............................................................................. 43 Entering setup ............................................................................... 43 Standard CMOS setup .................................................................. 44 BIOS features setup ...................................................................... 45 CHIPSET features setup ............................................................... 46 Power management setup .............................................................. 47 PnP/PCI Configuration ................................................................. 48 Integrated Peripherals ................................................................... 49 Load BIOS defaults ....................................................................... 50 Change Password .......................................................................... 51 Auto detect hard disk .................................................................... 52 Save & exit setup .......................................................................... 52 Exit without saving ....................................................................... 52 Chapter 5 PCI SVGA Setup..........................53 Before you begin ..................................................................................... 54 Installation .............................................................................................. 54 Simultaneous display mode .................................................................... 55 Sleep mode ............................................................................................... 55 Driver installation .................................................................................. 56 Necessary prerequisites ................................................................ 56 Before you begin .......................................................................... 56 Windows setup .............................................................................. 57 Changing Display Drivers in Windows ....................................... 57 Changing Color Schemes ............................................................. 57 DOS Setup .................................................................................... 58 Changing Display Drivers in DOS .............................................. 59 Panning Drivers ............................................................................ 59 Linear Acceleration Drivers ......................................................... 59 Windows 95 Drivers Setup Procedure .................................................. 59 Windows NT Drivers Setup Procedure ................................................ 60 Step 1 ............................................................................................ 60 Step 2 ............................................................................................ 60 Step 3 ............................................................................................ 60 OS/2 Drivers Setup Procedure .............................................................. 61 Preliminary Steps .......................................................................... 61 Installing from Diskette ................................................................. 61 Selecting Monitor Type ................................................................. 63 Selecting Screen Resolution/Refresh Rate .................................... 63 Installation Notes .......................................................................... 64 Chapter 6 Audio Setup .................................65 Introduction ............................................................................................ 66 DOS Utilities ........................................................................................... 66 Changing setting in DOS ............................................................. 66 Controlling volume in DOS ......................................................... 67 Driver Installation .................................................................................. 68 Before you begin ........................................................................... 68 Windows 3.1 drivers ..................................................................... 68 Windows 95 Drivers ..................................................................... 69 Appendix A The Watchdog Timer ...............71 Programming the Watchdog Timer ...................................................... 72 Appendix B Installing PC/104 Modules ......73 B.1 Installing PC/104 modules ............................................................. 74 Figure B-1: PC/104 module mounting diagram .................................. 74 Figure B-2: PC/104 module dimensions (mm) (0.1) .......................... 74 Appendix C Pin Assignments .....................77 CRT display connector (CN1) ....................................................... 78 Flat panel display connector (CN2) .............................................. 79 PC/104 connectors (CN3, CN9) ................................................... 80 USB connectors (CN4, CN5) ....................................................... 82 Fan power connector (CN6) .......................................................... 82 Front panel connector (CN7) ........................................................ 83 CD audio connector (CN8) ........................................................... 84 Peripheral power connector (CN10) ............................................. 84 Ethernet 10BASE-T connector (CN11) ........................................ 85 IR connector (CN12) ..................................................................... 85 Audio connector (CN13) ............................................................... 86 Main power connector (CN14) ..................................................... 86 Keyboard and PS/2 mouse connector (CN15) .............................. 87 COM port connector (CN16) ........................................................ 88 IDE hard drive connector (CN17) ................................................ 90 Floppy drive connector (CN18) .................................................... 91 Parallel port connector (CN19) ..................................................... 92 ATX Power Feature Connector (CON1) ....................................... 93 ATX Soft Power Switch Connector (CON2) ................................ 93 System I/O Ports ..................................................................................... 94 1st MB Memory Map ............................................................................. 95 DMA Channel Assignments .................................................................. 95 IRQ mapping chart ................................................................................ 96 Appendix D Optional Extras ........................97 PCM-10586-2 Cable kit for PCM-5862E/5862EL .............................. 98 USB Cables & LCD Cables ................................................................... 99 General Information This chapter gives background information on the PCM-5862E/5862EL Sections include: * Introduction * Features * Specifications * Board layout and dimensions CHAPTER 1 Introduction The PCM-5862E/5862EL is an all-in-one multi-media Pentium processor-based single board computer (SBC) with a 16-bit audio controller, a PCI SVGA controller, a PCI 100/10 base-T Ethernet interface, and one PCI expansion slot. When using an Intel MMX Pentium processor, the PCM-5862E/5862EL achieves outstanding performance that surpasses any other SBC in its class. This compact (only 5.75" x 8") unit offers all the functions of a single board industrial computer, but still fits in the space of a 5.25" floppy drive. On-board features include 512 KB 2nd level cache, four serial ports (three RS-232, one RS-232/422/485), one multi-mode parallel (ECP/EPP/SPP) port, two USB (Universal Serial Bus) ports, a floppy drive controller and a keyboard/PS/2 mouse interface. The built-in high speed PCI IDE controller supports both PIO and bus master modes. Up to two IDE devices can be connected, including large hard disks, CD-ROM drives, and tape backup drives. The PCM-5862E/5862EL features power management to minimize power consumption. It complies with the "Green Function" standard and supports Doze mode, Standby mode and Suspend mode. In addition, the board`s watchdog timer can automatically reset the system or generate an interrupt in case the system stops due to a program bug or EMI. Highly integrated multi-media SBC The PCM-5862E/5862EL is a highly integrated multi-media SBC that combines audio, video, and network functions on a single computer board the size of a 5.25" floppy drive. It provides 16-bit half-duplex, 8-bit full-duplex, integrated 3D audio and up to 1024 x 768 resolution @ 64K colors with 2MB display memory. Major on-board devices adopt PCI technology to achieve outstanding computing performance when used with Intel Pentium processors, making the PCM-5862E/5862EL the world`s smallest and most powerful all-in-one multimedia board. 2 PCM-5862E/EL User's Manual Features * Accepts Intel MMX Pentium, AMD K6, and Cyrix 6x86MX, IDT WinChip C6 * 32-bit PCI-bus SVGA/LCD controller supports LCD & CRT display * 100/10Base-T Ethernet interface, IEEE 802.3U compatible * 16-bit audio interface, Sound Blaster Pro compatible * 4 serial ports (three RS-232 and one RS-232/422/485) * USB interface, PCI slot, and PC/104 connector for flexible expansion capabilities * Watchdog timer with jumperless selection * Switching power for full range Pentium MMX level processors Specifications Standard SBC functions * CPU: Intel Pentium MMX up to 233MHz AMD K6 up to 300MHz Cyrix 6x86MX-PR166, PR200, PR233 IDT WinChip C6 up to 200MHz, * BIOS: AWARD 256KB Flash BIOS, supports Plug&Play, APM * Chipset: SiS 5571 * Green function: APM 1.1 compliant * 2nd level cache: On board 512 KB Pipelined Burst SRAM * RAM: Two 72-pin SIMM sockets accept 8~128 MB EDO/FPM DRAM * Enhanced IDE interface: Supports 2 IDE devices * FDD interface: Supports up to two FDDs (360K/1.2M/720K/ 1.44MB/ 2.88MB) Chapter 1 General Information 3 * Parallel port: One parallel port, supports SPP/EPP/ECP parallel mode * Serial port: Four serial ports with three RS-232 (COM1, 3, 4) and one RS-232/422/485 (COM2). All ports with 16C550 compatible UARTs. * Watchdog timer: 63-level interval from 1 to 63 seconds. Generates system reset or IRQ15. Jumperless selection and software enabled/disabled. * Keyboard/Mouse connector: 8-pin header connector for keyboard and PS/2 mouse * USB interface: Two USB connectors with fuse protection. Compliant with USB Spec. Rev. 1.0 * PC/104 expansion: 104-pin 16-bit PC/104 module connector * I/O bus expansion: One 32-bit PCI bus expansion slot * Switch voltage regulator: To support a full range of processor voltage requirements. A solution for processor overheating. PCI SVGA/flat panel interface: * Chipset: C&T 65550 * Display memory: 1 MB on-board memory, supports up to 2 MB * Display type: Simultaneously supports CRT and flat panel (EL, LCD and gas plasma) displays * Display resolution: Supports non-interlaced CRT and LCD display up to 1024x768@256 colors with 1MB VGA memory or 1024x768@64K colors with 2MB(PCM-5862E only) Audio function: (PCM-5862E only) * Chipset: ESS 1868 * Audio controller: 16-bit codec, Sound Blaster Pro compatible * Stereo sound: 8-bit full-duplex, 16-bit half-duplex integrated 3D audio * Audio interface: Microphone in, Line in, CD audio in; Line out, Speaker L, Speaker R * Power: Accepts +12 V source for improved audio quality 4 PCM-5862E/EL User's Manual PCI Bus Ethernet Interface: * Chipset: REALTEK RTL8139A PCI local bus Ethernet controller * Ethernet Interface: IEEE 802.3U compatible 100/10BaseT interface. Includes software drivers & boot ROM Mechanical and environmental * * * * Max. power requirements: 7A @ 5V (4.75V to 5.25V) Operating temperature: 0 to 60 C (32 to 140 F) Size: 203 mm (L) x 146 mm (W) (8" x 5.75") Weight: 0.32 kg (0.7 lbs.) (w/o package) Board layout and dimensions PCM-5862E/5862EL dimensions Chapter 1 General Information 5 6 PCM-5862E/EL User's Manual CHAPTER 2 Installation This chapter tells how to set up the PCM5862E/5862EL hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installation procedure. Chapter 2 Installation 7 Jumpers The PCM-5862E/5862EL has a number of jumpers that allow you to configure your system to suit your applications. The table below lists the function of each of the board's jumpers. Jumpers Label JP1 JP2 J1 J2 J4 J5 J6 J7 J10 J11 J12 J13 J14 J15 J16 Function CPU voltage setting Pentium MMX enable/disable System/PCI clock setting System/PCI clock setting CPU frequency ratio setting M1 cache linear mode setting CMOS clear Buzzer enable/disable LCD power setting COM4 RI pin setting COM3 RI pin setting Watchdog timer action COM2 RS-232/422/485 setting COM2 RS-232/422/485 setting Audio power source setting 8 PCM-5862E/EL User's Manual Connectors On-board connectors link the PCM-5862E/5862EL to external devices such as hard disk drives, a keyboard, or floppy drives. The table below lists the function of each of the board's connectors. Connectors Label CN1 CN2 CN3 CN4 CN5 CN6 CN7 CN8 CN9 CN10 CN11 CN12 CN13 CN14 CN15 CN16 CN17 CN18 CN19 CON1 CON2 Function CRT display connector Flat panel display connector PC/104 ISA-bus expansion USB channel 1 connector USB channel 2 connector Fan power connector Front panel connector CD audio input connector PC/104 ISA-bus expansion Peripheral power connector Ethernet 100/10Base-T connector IR connector Audio connector Main power connector Keyboard and PS/2 mouse connector COM-port connector IDE hard drive connector Floppy drive connector Parallel port connector ATX feature connector ATX soft power connector switch Please refer to Appendix C for pin assignment. Chapter 2 Installation 9 Locating jumpers J13 J5 J14 J15 J16 J12 J11 J10 J9 J4 JP1 J2 J1 J7 JP2 J6 J8 10 PCM-5862E/EL User's Manual Locating connectors CN15 CN18 CN17 CN19 CN14 CN13 CN12 CN16 CN9 CN10 CN7 CN4 CN5 CN11 CN8 CON1 CON2 CN2 CN1 CN6 CN3 Chapter 2 Installation 11 Setting jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To "close" a jumper you connect the pins with the clip. To "open" a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case you would connect either pins 1 and 2 or 2 and 3. 1 2 3 Open Closed Closed 2-3 The jumper settings are schematically depicted in this manual as follows: 1 Open Closed Closed 2-3 A pair of needle-nose pliers may be helpful when working with jumpers. If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes. Generally, you simply need a standard cable to make most connections. 12 PCM-5862E/EL User's Manual CPU installation and upgrading You can upgrade to a higher power Pentium processor at any time. Simply remove the old CPU, install the new one, and set the jumpers for the new CPU type and speed. Warning! Always disconnect the power cord from your chassis when you are working on it. Do not make connections while the power is on as sensitive electronic components can be damaged by the sudden rush of power. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the PC board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times. Place all electronic components on a static-dissipative surface or in a static-shielded bag when they are not in the chassis. Install a CPU in the ZIF socket PCM-5862E/5862EL provides a Zero Insertion Force (ZIF) socket for easy CPU installation. 1. Make sure the ZIF socket lever is in the upright position. To raise the lever, pull it out to the side a little and raise it as far as it will go. 2. Place the CPU in the empty socket. Follow the instructions that came with the CPU. If you have no instructions, do the following: Carefully align the CPU so it is parallel to the socket and the notch on the corner of the CPU corresponds with the notch on the inside of the socket. Gently slide the CPU in. It should insert easily. If it doesn`t, pull the lever up a little more. Chapter 2 Installation 13 3. Press the lever down. The plate will slide forward. You will feel some resistance as the pressure starts to secure the CPU in the socket. This is normal and won`t damage the CPU. When the CPU is installed, the lever should snap into place at the side of the socket. NOTE: To remove a CPU, pull the lever out to the side a little and raise it as far as it will go. Lift out the CPU chip. When you install a new CPU, be sure to adjust the board settings, such as CPU type and CPU clock. Improper settings may damage the CPU. System clock setting (J1, J2, and J4) J1, J2 and J4 are used to set the CPU and PCI bus speed to optimize the system performance. The system chipset will sense the J1 setting to get the bus frequency, then adjust its internal timing. J2 is used to set the CPU and PCI clock. J4 is the CPU clock ratio setting jumper. Refer to the CPU Speed Reference Table (below) for instructions on adjusting the internal clocks according to the base CPU speed. CPU Speed Reference Table CPU Speed (MHz) Clock setting Frequency ratio 75 50 1.5 100 *133 150 66 1.5 66 2 60 2.5 166 66 2.5 200 66 3 233 66 3.5 266 300 66 4 66 4.5 * default setting 14 PCM-5862E/EL User's Manual System/PCI clock setting System PCI J1 50MHz 25MHz 1 3 5 50MHz 33.3MHz 1 3 5 60MHz 30MHz 1 3 5 *66MHz *33.3MHz 1 3 5 1 75MHz 32MHz 3 5 2 1 4 3 6 5 2 1 4 3 6 5 2 1 4 3 6 5 2 1 4 3 6 5 2 1 4 3 6 5 J2 2 4 6 2 4 6 2 4 6 2 4 6 2 4 6 CPU frequency ratio 1.5/3.5 1 3 5 1 *2 3 5 1 2.5 3 5 1 3 3 5 1 4 3 5 J4 2 4 6 2 4 6 2 4 6 2 4 6 2 4 6 4.5 1 3 5 5 (Reserve) 1 3 5 5.5(Reserve) 1 3 5 J4 cont. 2 4 6 2 4 6 2 4 6 Pentium MMX(P55C) enabled/disabled (JP2) P55C enabled 1 3 *P55C disabled 1 3 JP2 2 4 2 4 * default setting Chapter 2 Installation 15 CPU voltage setting (JP1) JP1 must be set to match the CPU type. The chart below shows the proper jumper settings for their respective Vcc (core). (The Vcc (I/O) for CPU is fixed to be 3.3V) CPU voltage setting JP1 V CC(CORE) NONE 2.10V 2.20V 2.30V 2.40V 2.50V 2.60V 2.70V 2.80V 2.90V 3.00V 3.10V 3.20V 3.30V* 3.40V 3.50V 1-2 open closed open closed open closed open closed open closed open closed open closed open closed 3-4 open open closed closed open open closed closed open open closed closed open open closed closed 5-6 open open open open closed closed closed closed open open open open closed closed closed closed 7-8 open open open open open open open open closed closed closed closed closed closed closed closed * default setting M1 cache linear mode setting (J5) PCM-5862E/5862EL supports Cyrix M1 CPU with its linear access mode on L2 cache. This mode is set through J5. M1 cache linear mode enabled/disabled Enabled J5 *Disabled * default setting 16 PCM-5862E/EL User's Manual CMOS clear (J6) Warning: To avoid damaging the computer, always turn off the power supply before setting "Clear CMOS." Set the jumper back to "3.6V Battery On" before turning on the power supply. CMOS clear *3.6V Battery On 1 2 3 Clear CMOS 1 2 3 J6 * default setting Buzzer enabled/disabled (J7) Buzzer enabled/disabled *Enabled J7 Disabled * default setting Installing DRAM (SIMMs) The PCM-5862E/5862EL CPU card provides two 72-pin SIMM (Single In-line Memory Module) sockets and supports either Fast Page Mode (FPM) or Extended Data Output (EDO) DRAM with a speed of 70 ns or faster. You can install from 8 MB to 128 MB of RAM. Installing SIMMs NOTE: The modules can only fit into a socket one way. Their chips must face the CPU, and their gold pins must point down into the SIMM socket. 1. Ensure that all power sources are disconnected. Chapter 2 Installation 17 2. Slip the memory module into the socket at a 45-degree angle. 3. Push the module toward the vertical posts at both ends of the socket until the module is upright, and the retaining clips at both ends of the module click into place. When positioned correctly, the pins on top of the vertical posts should correspond to the circular holes on the ends of the module. 4. Repeat steps 2 and 3 for each module you install. IDE hard drive connector (CN17) You can attach one or two Enhanced Integrated Device Electronics hard disk drives to the PCM-5862E/5862EL's internal controller. The PCM-5862E/5862EL's IDE controller uses a PCI local-bus interface. This advanced IDE controller supports faster data transfer, PID mode 3, mode 4. Connecting the hard drive Connecting drives is done in a daisy-chain fashion and requires one of two cables (not included in this packing), depending on the drive size. 1.8" and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flat-cable connector. 3.5" drives use a 1 x 44-pin to 2 x 40-pin connector. Wire number 1 on the cable is red or blue, and the other wires are gray. 1. Connect one end of the cable to CN17. Make sure that the red (or blue) wire corresponds to pin 1 on the connector, which is labeled on the board (on the right side). 2. Plug the other end of the cable to the Enhanced IDE hard drive, with pin 1 on the cable corresponding to pin 1 on the hard drive. (See your hard drive's documentation for the location of the connector.) Connect a second drive as described above. Unlike floppy drives, IDE hard drives can connect to either end of the cable. If you install two drives, you will need to set one as the master and one as the slave by using jumpers on the drives. If you install just one drive, set it as the master. 18 PCM-5862E/EL User's Manual Floppy drive connector (CN18) You can attach up to two floppy drives to the PCM-5862E/ 5862EL's on-board controller. You can use any combination of 51/4" (360 KB and 1.2 MB) and/or 31/2" (720 KB, 1.44 MB, and 2.88 MB) drives. A 34-pin daisy-chain drive connector cable is required for a dualdrive system. On one end of the cable is a 34-pin flat-cable connector. On the other end are two sets of floppy disk drive connectors. Each set consists of a 34-pin flat-cable connector (usually used for 31/2" drives) and a printed-circuit board connector (usually used for 51/4" drives). Connecting the floppy drive 1. Plug the 34-pin flat-cable connector into CN18. Make sure that the red wire corresponds to pin one on the connector. 2. Attach the appropriate connector on the other end of the cable to the floppy drive(s). You can use only one connector in the set. The set on the end (after the twist in the cable) connects to the A: drive. The set in the middle connects to the B: drive. 3. If you are connecting a 51/4" floppy drive, line up the slot in the printed circuit board with the blocked-off part of the cable connector. If you are connecting a 31/2" floppy drive, you may have trouble determining which pin is pin number one. Look for a number printed on the circuit board indicating pin number one. In addition, the connector on the floppy drive connector may have a slot. When the slot is up, pin number one should be on the right. Check the documentation that came with the drive for more information. If you desire, connect the B: drive to the connectors in the middle of the cable as described above. If you need to make your own cable, you can find the pin assignments for the board's connector in Appendix C. Chapter 2 Installation 19 Parallel port connector (CN19) Normally, the parallel port is used to connect the card to a printer. The PCM-5862E/5862EL includes a multi-mode (ECP/EPP/SPP) parallel port, accessed through CN19, a 26-pin flat-cable connector. You will need an adapter cable if you use a traditional DB-25 connector. The adapter cable has a 26-pin connector on one end and a DB-25 connector on the other. The parallel port is designated as LPT1 and can be disabled or changed to LPT2 or LPT3 in the system BIOS setup. The parallel port interrupt channel is designated to be IRQ7. You can select ECP/EPP DMA channel via BIOS setup. Keyboard and PS/2 mouse connector (CN15) The PCM-5862E/5862EL board provides a keyboard connector that supports both a keyboard and a PS/2 style mouse. In most cases, especially in embedded applications, a keyboard is not used. The standard PC/AT BIOS will report an error or fail during power-on self-test (POST) after a reset if the keyboard is not present. The PCM-5862E/5862EL's BIOS standard setup menu allows you to select "All, But Keyboard" under the "Halt On" selection. This allows no-keyboard operation in embedded system applications without the system halting under POST (power-onself-test). Front panel connector (CN7) Next, you may want to install external switches to monitor and control the PCM-5862E/5862EL. These features are optional -- install them only if you need them. The front panel connector (CN7) is an 8-pin male, dual in-line header and provides connections for a speaker, hard disk access indicator, watchdog output and an input switch for resetting the card. 20 PCM-5862E/EL User's Manual Speaker The PCM-5862E/5862EL can drive an 8 speaker at 0.5 watts. Ensure that alternatives to this specification do not overload the card. LED interface The front panel LED indicator for hard disk access is an active low signal (24 mA sink rate). Watchdog output When PCM-5862E/5862EL watchdog timer times out, the front panel pin 6 will output an active low pulse signal (25mA sink rate for 1 second). Reset switch If you install a reset switch, it should be an open single pole switch. Momentarily pressing the switch will activate a reset. The switch should be rated for 10 mA, 5 V. If you need to make your own cable, you can find the pin assignments for the board's connector in Appendix C. Power connectors (CN6, CN10, CN14) Peripheral power connector, -5V, -12V (CN10) Supplies secondary power to devices that require -5 V and -12 V. Main power connector, +5V, +12V (CN14) Supplies main power to the PCM-5862E/5862EL (+5 V) and devices that require +12 V. Fan power supply connector (CN6) Provides power supply to optional CPU cooling fan. Only present when +5 V and +12 V power is supplied to the board. Chapter 2 Installation 21 ATX Power Control Connector (CON1, CON2) ATX feature connector (CON1) and soft power switch connector (CON2) The PCM-5862E/5862EL can support an advanced soft power switch function if an ATX power supply is used. To enable the soft power switch function: 1. Take the specially designed ATX-to-PS/2 power cable (PCM-5862E/5862EL option item) 2. Connect the 3-pin plug of the cable to CON1 (ATX feature connector). 3. Connect the power on/off button to CON2. (A momentary type of button should be used.) Important: Be sure that the ATX power supply can take at least a 10 mA load on the 5 V standby lead (5VSB). If not, you may have difficulty powering on your system. Wiring for ATX soft power switch function 22 PCM-5862E/EL User's Manual IR connector (CN12) This connector supports the optional wireless infrared transmitting and receiving module. This module mounts on the system case. You must configure the setting through BIOS setup. Audio interfaces (CN8, CN13) The PCM-5862E/5862EL is equipped with a high quality audio interface, which provides 16-bit CD-quality recording and playback as well as OPL3 compatible FM music. It is supported by all major operating systems and is 100% Sound Blaster Pro compatible. Audio connector (CN13) The PCM-5862E/5862EL provides all major audio signals on a 16pin flat-cable connector, CN13. These audio signals includes Microphone in (mono), Line in (stereo), Line out (stereo), Speaker out (stereo). You will need an adapter cable if you use traditional telephone jack connectors for these audio signals. CD audio input connector (CN8) All CD-ROM drives can provide analog audio signal output when used as a music CD player. The CN8 on PCM-5862E/5862EL is a connector to input CD audio signal into the audio controller. The audio cable of your CD-ROM drive will be used to connect to CN8. Chapter 2 Installation 23 Audio power source setting (J16) The PCM-5862E/5862EL is designed to work with a single +5V power supply. The audio interface can also function normally under single +5V power supply, but most audio controllers require an independent power source generated from a +12V power. The independent power source avoids the noise from the other digital circuits. The PCM-5862E/5862EL`s audio interface can also accept +12V power to provide improved quality audio. This is done via J16. Audio power source setting *+5 V 1 2 3 +12 V 1 2 3 J16 * default setting Configuration of the audio interface is done completely via the software utility. You don't have to set any jumpers. Refer to Chapter 6 for audio setup details. 24 PCM-5862E/EL User's Manual COM-port connector (CN16) The PCM-5862E/5862EL provides four serial ports (COM1, 3, 4: RS-232; COM2: RS-232/422/485) in one COM port connector. The COM port connector is a 40-pin, dual-in-line, male header and provides connections for serial devices (a mouse, etc.) or a communication network. You can find the pin assignments for the COM port connector in Appendix C. COM2 RS-232/422/485 setting (J14, J15) COM2 can be configured to operate in RS-232, RS-422, or RS-485 mode. This is done via J14 and J15. COM2 RS-232/422/485 setting *RS-232 1 3 5 RS-422 1 3 5 RS-485 1 3 5 J14 2 4 6 2 4 6 2 4 6 12 11 10 12 11 10 12 11 10 J15 3 2 1 3 2 1 3 2 1 * default setting Chapter 2 Installation 25 The IRQ and the address range for COM1, 2, 3, 4 are fixed. However, if you wish to disable the port or change these parameters later you can do this in the system BIOS setup. The table below shows the settings for the PCM-5862E/5862EL's serial ports. PCM-5862E/5862EL serial port default settings Port COM1 COM2 COM3 COM4 Address Range 3F8~3FF 2F8~2FF 3E8~3EF 2E8~2EF Interrupt IRQ4 IRQ3 IRQ10 IRQ5 COM3/COM4 RI pin setting (J11, J12) The COM3 and COM4 can supply +5V or +12V power to the serial devices via RI pin of the COM port connector. The outputs of COM3, COM4 RI pins are selected by setting J11, J12. COM3 RI pin setting +5V 1 3 5 1 +12V 3 5 1 *RI 3 5 J12 2 4 6 2 4 6 2 4 6 COM4 RI pin setting +5V 1 3 5 1 +12V 3 5 1 *RI 3 5 J11 2 4 6 2 4 6 2 4 6 * default setting 26 PCM-5862E/EL User's Manual VGA interface connections The PCM-5862E/5862EL's PCI SVGA interface can drive conventional CRT displays and is capable of driving a wide range of flat panel displays, including electroluminescent (EL), gas plasma, passive LCD and active LCD displays. The board has two connectors to support these displays, one for standard CRT VGA monitors and one for flat panel displays. CRT display connector (CN1) CN1 is a 16-pin, dual-in-line header used for conventional CRT displays. A simple one-to-one adapter can be used to match CN1 to a standard 15-pin D-SUB connector commonly used for VGA. Pin assignments for CRT display connector CN1 are detailed in Appendix C. Flat panel display connector (CN2) CN2 consists of a 44-pin, dual-in-line header. Power supply (+12V) present on CN2 depends on the supply connected to the board. Ensure that both CN10 and CN14 are connected for 12 V power supply. The PCM-5862E/5862EL provides a bias control signal on CN2 that can be used to control the LCD bias voltage. It is recommended that the LCD bias voltage not be applied to the panel until the logic supply voltage (+5V or +3.3V) and panel video signals are stable. Under normal operation, the control signal (ENAVEE) is active high. When the PCM-5862E/5862EL's power is applied, the control signal is low until just after the relevant flat panel signals are present. Chapter 2 Installation 27 LCD power setting (J10) The PCM-5862E/5862EL's PCI SVGA interface supports 5V and 3.3V LCD displays. By changing the setting of J10, you can select the panel video signal level to be 5V or 3.3V. LCD power setting *5 V 1 3 5 1 3.3 V 3 5 J10 2 4 6 2 4 6 * default setting Configuration of the VGA interface is done completely via the software utility. You don't have to set any jumpers. Refer to Chapter 3 for software setup details. Refer to Chapter 3 for details on connecting the five standard LCD's: Sharp LM64183P, LM64P89, Toshiba LTM10C042, Sharp 64C142, and Planar EL Display. 28 PCM-5862E/EL User's Manual Ethernet configuration The PCM-5862E/5862EL is equipped with a high performance 32bit PCI-bus Ethernet interface which is fully compliant with IEEE 802.3U 10/100Mbps CSMA/CD standards. It is supported by all major network operating systems and is 100% Novell NE-2000 compatible. The medium type can be configured via the RSET8029.EXE program included on the utility disk. (See Chapter 3 for detailed information.) 100BASE-T connector (CN11) 100BASE-T connects to the PCM-5862E/5862EL via an adapter cable to a 10-pin polarized header (CN11). For 10BASE-T RJ-45 operation, an adapter cable converting CN11 into a standard RJ-45 jack is required. Network boot The Network Boot feature can be utilized by incorporating the Boot ROM image files for the appropriate network operating system. The Boot ROM BIOS files are on the included utility disk. Chapter 2 Installation 29 Watchdog timer configuration An on-board watchdog timer reduces the chance of disruptions which EMP (electro-magnetic pulse) interference can cause. This is an invaluable protective device for standalone or unmanned applications. Setup involves one jumper and running the control software (refer to Appendix A). Watchdog timer action (J13) When the watchdog timer activates (CPU processing has come to a halt), it can reset the system or generate an interrupt on IRQ15. This can be set via setting J13 as shown below: Watchdog timer action *System reset IRQ15 1 J13 2 3 1 2 3 * default setting 30 PCM-5862E/EL User's Manual USB connectors (CN4, CN5) The PCM-5862E/5862EL board provides two USB (Universal Serial Bus) interfaces which gives complete plug and play, hot attach/detach for up to 127 external devices. The USB interfaces comply with USB specification rev. 1.0 and are fuse protected. The USB interfaces are accessed through two 4-pin flat-cable connectors, CN4 and CN5. You will need an adapter cable if you use a standard USB connector. The adapter cable has a 4-pin connector on one end and an USB connector on the other. The USB interfaces can be disabled in the system BIOS setup. Chapter 2 Installation 31 32 PCM-5862E/EL User's Manual 3 Software Configuration This chapter details the software configuration information. It shows you how to configure the card to match your application requirements. AWARD System BIOS is covered in Chapter 4. Sections include: * Introduction * Connections for four standard LCDs * Ethernet interface configuration Chapter 3 Software Configuration CHAPTER 33 Introduction The PCM-5862E/5862EL system BIOS and custom drivers are located in a 128 Kbyte, 32-pin (JEDEC spec.) Flash ROM device, designated U19. A single Flash chip holds the system BIOS, VGA BIOS, and network Boot ROM image. The display can be configured via CMOS settings. This method minimizes the number of chips and difficultly of configuration. To set different types of LCD panels please choose "panel type" from the "itergrated peripherals" menu in CMOS setup. Connections for five standard LCDs Connections to Sharp LM64183P, LM64P89 (640 x 480 DSTN MONO LCD) LM64183/64P89 Pin CN1-1 CN1-2 CN1-3 CN1-4 CN1-5 CN1-6 CN1-7 CN1-8 CN1-9 CN1-10 CN1-11 CN1-12 CN1-13 CN1-14 CN1-15 Pin name S CP1 CP2 DISP VDD VSS VEE DU0 DU1 DU2 DU3 DL0 DL1 DL2 DL3 PCM-5862E/5862EL CN2 Pin 36 38 35 5 6 3 12 11 10 9 16 15 14 13 Pin name FLM LP SHFCLK +5 V +5 V GND external power* P3 P2 P1 P0 P7 P6 P5 P4 *LM64183P -17V LM64P89 -20V 34 PCM-5862E/EL User's Manual Connections to PLANAR EL (640 x 480 AD4 EL) PLANAR 640 x 480 AD4 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31,32 33 34 Pin name GND DO GND D1 GND D2 NC D3 NC D4 NC D5 NC D6 GND D7 GND VCLK GND /BLANK GND HS NC VS NC SELFTST COLMAP ENABLE RESERVED /LOWPOW NC RESERVED NC PCM-5862E/5862EL CN2 Pin 3 21 3 22 3 23 -- 24 -- 17 -- 18 -- 19 4 20 4 42 4 -- 8 37 -- 36 -- 39 39 -- -- -- -- -- -- Pin name GND P12 GND P13 GND P14 -- P15 -- P8 -- P9 -- P10 GND P11 GND ASHFCLK GND -- GND M -- FLM -- GND GND -- -- -- -- -- -- Chapter 3 Software Configuration 35 Connections to Toshiba LTM10C042 (640 x 480 TFT Color LCD) LTM10C042 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31,32 Pin name GND CLK GND R0 R1 R2 GND R3 R4 R5 GND G0 G1 G2 GND G3 G4 G5 GND ENAB GND B0 B1 B2 GND B3 B4 B5 GND VDD VDD PCM-5862E/5862EL CN2 Pin 3 35 4 27 28 29 8 30 31 32 33 19 20 21 33 22 23 24 34 37 34 11 12 13 39 14 15 16 39 5 6 Pin name GND SHFCLK GND P18 P19 P20 GND P21 P22 P23 GND P10 P11 P12 GND P13 P14 P15 GND M GND P2 P3 P4 GND P5 P6 P7 GND +5V +5V 36 PCM-5862E/EL User's Manual Connections to Sharp LM64C142 (640 x 480 DSTN Color LCD) LM64C142 Pin CN1-1 CN1-2 CN1-3 CN1-4 CN1-5 CN1-6 CN1-7 CN1-8 CN1-9 CN1-10 CN1-11 CN1-12 CN1-13 CN1-14 CN1-15 CN2-1 CN2-2 CN2-3 CN2-4 CN2-5 CN2-6 CN2-7 CN2-8 CN2-9 CN2-10 Pin name YD LP XCX DISP VDD VSS VEE DU0 DU1 DU2 DU3 DU4 DU5 DU6 DU7 VSS DL0 DL1 DL2 DL3 DL4 DL5 DL6 DL7 VSS PCM-5862E/5862EL CN2 Pin 36 38 35 5 6 3 -- 20 19 18 17 12 11 10 9 4 24 23 22 21 16 15 14 13 8 Pin name FLM LP SHFCLK +5V +5V GND +27* P11 P10 P9 P8 P3 P2 P1 P0 GND P15 P14 P13 P12 P7 P6 P5 P4 GND Chapter 3 Software Configuration 37 Connections to Toshiba LTM12C275A (800 x 600 TFT Color LCD) LTM12C275A Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Pin name GND NCLK NC NC GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 ENAB GND VCC VCC GND PCM-5862E/5862EL CN2 Pin 3 35 4 27 28 29 30 31 32 8 19 20 21 22 23 24 33 11 12 13 14 15 16 37 34 5 6 39 Pin name GND SHFCLK NC NC GND P18 P19 P20 P21 P22 P23 GND P10 P11 P12 P13 P14 P15 GND P2 P3 P4 P5 P6 P7 M/DE GND +5 V +5 V GND 38 PCM-5862E/EL User's Manual Ethernet software configuration The PCM-5862E/5862EL's on-board Ethernet interface supports all major network operating systems. To configure the medium type, to view the current configuration, or to run diagnostics, do the following: 1. Power the PCM-5862E/5862EL on. Ensure that the RSET8139.EXE file is located in the working drive. 2. At the prompt type RSET8139.EXE and press Chapter 3 Software Configuration 39 System test and initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. Non-fatal error messages usually appear on the screen along with the following instructions: press Write down the message and press the F1 key to continue the bootup sequence. System configuration verification These routines check the current system configuration against the values stored in the board's CMOS memory. If they don't match, the program outputs an error message. You will then need to run the BIOS setup program to set the configuration information in memory. There are three situations in which you will need to change the CMOS settings: 1. You are starting your system for the first time 2. You have changed the hardware attached to your system 3. The CMOS memory has lost power and the configuration information has been erased. The PCM-5862E/5862EL's CMOS memory has an integral lithium battery backup. The battery backup should last ten years in normal service, but when it finally runs down, you will need to replace the complete unit. 40 PCM-5862E/EL User's Manual 4 Award BIOS Setup This chapter describes how to set BIOS configuration data. Chapter 4 Award Bios Setup CHAPTER 41 System test and initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors. Non-fatal error messages usually appear on the screen along with the following instructions: press Write down the message and press the F1 key to continue the bootup sequence. System configuration verification These routines check the current system configuration against the values stored in the board's CMOS memory. If they don't match, the program outputs an error message. You will then need to run the BIOS setup program to set the configuration information in memory. There are three situations in which you will need to change the CMOS settings: 1. You are starting your system for the first time 2. You have changed the hardware attached to your system 3. The CMOS memory has lost power and the configuration information has been erased. The PCM-5862E/5862EL's CMOS memory has an integral lithium battery backup. The battery backup should last ten years in normal service, but when it finally runs down, you will need to replace the complete unit. 42 PCM-5862E/EL User's Manual AWARD BIOS setup Award's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering setup Power on the computer and press Setup program initial screen Chapter 4 Award Bios Setup 43 Standard CMOS setup When you choose the STANDARD CMOS SETUP option from the INITIAL SETUP SCREEN menu, the screen shown below is displayed. This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display. Once a field is highlighted, on-line help information is displayed in the left bottom of the Menu screen. CMOS setup screen 44 PCM-5862E/EL User's Manual BIOS features setup By choosing the BIOS FEATURES SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer's default values for the PCM-5862E/5862EL. BIOS features setup Chapter 4 Award Bios Setup 45 CHIPSET features setup By choosing the CHIPSET FEATURES SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer's default values for the PCM-5862E/5862EL. CHIPSET features setup 46 PCM-5862E/EL User's Manual Power management setup By choosing the POWER MANAGEMENT SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer's default values for the PCM-5862E/5862EL. Power management setup Chapter 4 Award Bios Setup 47 PnP/PCI Configuration By choosing the PnP/PCI CONFIGURATION option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer's default values for the PCM-5862E/5862EL. PnP/PCI Configuration 48 PCM-5862E/EL User's Manual Integrated Peripherals By choosing the INTEGRATED PERIPHERALS option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer's default values for the PCM-5862E/5862EL. Integrated Peripherals Chapter 4 Award Bios Setup 49 Load BIOS defaults LOAD BIOS DEFAULTS loads the default system values directly from ROM. If the stored record created by the Setup program becomes corrupted (and therefore unusable), these defaults will load automatically when you turn the PCM-5862E/5862EL on. Load BIOS defaults screen 50 PCM-5862E/EL User's Manual Change Password To change the password, choose the PASSWORD SETTING option form the Setup main menu and press 1. If the CMOS is bad or this option has never been used, a default password is stored in the ROM. The screen will display the following messages: Enter Password: Press 2. If the CMOS is good or this option has been used to change the default password, the user is asked for the password stored in the CMOS. The screen will display the following message: Confirm Password: Enter the current password and press 3. After pressing Auto detect hard disk Chapter 4 Award Bios Setup 51 The IDE HDD AUTO DETECTION utility can automatically detect the IDE hard disk installed in your system. You can use it to self-detect and/or correct the hard disk type configuration. IDE HDD auto detection screen Save & exit setup If you select this option and press Exit without saving Selecting this option and pressing 52 PCM-5862E/EL User's Manual PCI SVGA Setup The PCM-5862E/5862EL features an onboard PCI flat panel/VGA interface. This chapter provides instructions for installing and operating the software drivers on the included display driver diskette. Chapter 5 PCI VGA Setup CHAPTER 5 53 Before you begin To facilitate the installation of the enhanced display device drivers and utility software, you should read the instructions in this chapter carefully before you attempt installation. The enhanced display drivers for the PCM-5862E/5862EL board are located on the software installation diskette. You must install the drivers and utility software by using the supplied SETUP program for DOS drivers Note: The files on the software installation diskette are compressed. Do not attempt to install the drivers by copying the files manually. You must use the supplied SETUP program to install the drivers. Before you begin, it is important to note that most display drivers need to have the relevant software application already installed in the system prior to installing the enhanced display drivers. In addition, many of the installation procedures assume that you are familiar with both the relevant software applications and operating system commands. Review the relevant operating system commands and the pertinent sections of your application software's user's manual before performing the installation. Installation Disk 1: Disk 2: Windows 3.1, Windows 95, and Windows NT drivers OS/2 drivers 54 PCM-5862E/EL User's Manual Simultaneous display mode The 65550 VGA BIOS supports monochrome LCD, EL, color TFT and STN LCD flat panel displays. It also supports interlaced and non-interlaced analog monitors (VGA color and VGA monochrome) in high-resolution modes while maintaining complete IBM VGA compatibility. Digital monitors (i.e. MDA, CGA, and EGA) are NOT supported. Multiple frequency (multisync) monitors are supported as analog monitors. Both CRT and panel displays can be used simultaneously. The PCM-5863E/5862EL can be set in one of three configurations: on a CRT, on a flat panel display, or on both simultaneously. The system is initially set to simultaneous display mode. In the utility diskette, there are three .COM files that can be used to select the display. Simply type the filename at the DOS prompt: CT.COM Enables CRT display only FP.COM Enables panel display only SM.COM Enables both displays at the same time. Sleep mode The display driver diskette contains two files that support sleep mode. Simply type the filename at the DOS prompt: ON.COM switches to normal display mode. OFF.COM switches to sleep mode. Chapter 5 PCI VGA Setup 55 Driver installation Necessary prerequisites The instructions in this manual assume that you understand elementary concepts of MS-DOS and the IBM Personal Computer. Before you attempt to install any driver or utility you should: know how to copy files from a floppy disk to a directory on the hard disk, understand the MS-DOS directory structure, and know how to format a floppy disk. If you are uncertain about any of these concepts, please refer to the DOS or Windows user reference guides for more information before you proceed with the installation. Before you begin Before you begin installing software drivers, you should make a backup copy of the display driver diskette and store the original in a safe place. The display driver diskette contains drivers for several versions of certain applications. You must install the correct version in order for the driver to work properly so make sure you know which version of the application you have. 56 PCM-5862E/EL User's Manual Windows setup These drivers are designed to work with Microsoft Windows 3.1. You may install these drivers through Windows or in DOS. Step 1: Install Windows as you normally would for a VGA display. Run Windows to make sure that it is working correctly. Step 2: Place the display driver diskette in drive A. In Windows Program Manager, choose File from the Options Menu. Then from the pull-down menu, choose Run . . . . At the command line prompt, type A:\SETUP. Press the Chapter 5 PCI VGA Setup 57 DOS Setup Step 1: Install Windows as you normally would for a VGA display. Run Windows to make sure that it is working correctly. Then exit Windows. Step 2: Place the display driver diskette in drive A. Type A: 58 PCM-5862E/EL User's Manual Changing Display Drivers in DOS To change display drivers from DOS, change to the Windows directory and run Setup, repeating steps 4 and 5 from the previous page. Besides the special display drivers marked by an asterisk (*), you should be able to use the following standard drivers: VGA Super VGA 640x480, 16 colors 800x600, 16 colors Panning Drivers Special panning drivers are provided to allow high-resolution modes to be displayed on a flat panel or CRT. These drivers will show a section of a larger screen and will automatically pan, or scroll, the screen horizontally and vertically when the mouse reaches the edge of the display. Linear Acceleration Drivers A special high-performance linear acceleration driver is provided for 256-color modes. This driver may require special hardware and may not be supported on all systems. It is only available for Windows 3.1. Windows 95 Drivers Setup Procedure 1. Boot system with VGA or SuperVGA driver. 2. Select properties from a menu after right button press. 3. Select display. 4. Select Change Display. 5. Select Change Monitor. 6. Select Change Adapter. 7. Select Have Disk. Chapter 5 PCI VGA Setup 59 Windows NT Drivers Setup Procedure Step 1 1. Install Windows NT as you normally would for a VGA display. 2. First click the Start button, choose Settings and click on Control Panel. 3. Choose the Display icon and click on the icon. 4. In the Display Properties window, click on the Settings tab. 5. Click on Change Display Type. In the Change Display Type window, click on the Change button under Adapter Type. This will bring up the Select Device window. Step 2 1. In the Select Device window, click on the Other button. Enter source directory where the Windows NT driver files are located. 2. Press Step 3 1. Upon restarting your computer, select the desired display settings from the Display property dialog box. 2. Click on Test to test the newly selected graphics mode. A color test screen should appear, followed by the Testing Mode window. 3. Click on Yes to continue. The Display Settings Change window will appear. 4. Click on Restart Now for the new settings to take effect. 60 PCM-5862E/EL User's Manual OS/2 Drivers Setup Procedure Preliminary Steps The following steps must be performed before you install the 65550/554 display driver: 1. OS/2 DOS Support must be installed. 2. If you previously installed SVGA support, you must reset the system to VGA mode. VGA is the default video mode enabled when OS/2 is installed. To restore VGA mode, use Selective Install and select VGA for Primary Display. For more information on this procedure, see the section on Changing Display Adapter Support in the OS/2 User's Guide. Installing from Diskette To install this driver, do the following steps: 1. Open an OS/2 full screen or windowed session. 2. Place the 65550 PCI Display Driver Diskette in drive A. 3. At the OS/2 command prompt, type the following commands to copy the files to the OS/2 drive: Type: A: where A: is the floppy disk drive and C: is the hard disk partition containing \OS2 When the Setup Program is completed, you will need to perform a shutdown and then restart the system in order for changes to take effect. A log of the information output during the install can be found in Chapter 5 PCI VGA Setup 61 4. After restarting the system, perform the following steps: 1). Open the OS/2 System folder. 2). Open the System Setup folder. 3). Open the Display Driver Install Object This step will execute the Display Driver Installation (DSPINSTL) utility program to finish installation of the new drivers. 4). When the Display Driver Install window appears, select Primary Display and then select OK. 5). When The Primary Display Driver List window appears, select "Chips and Technologies 65550/554" from the list of adapter types, then select OK to install the video driver. 6). When the installation is complete, you will need to shutdown and then restart the system for the changes to take effect. Make sure to remove the install diskette before restarting the system. When the system has restarted, the display driver will be initialized for 640x480x256 Color, 60Hz refresh. To switch to a different video resolution color depth, or refresh rate, follow the steps below. 62 PCM-5862E/EL User's Manual Selecting Monitor Type Monitor type is initially set to DEFAULT. This DEFAULT setting may not allow you to select all resolution/refresh combinations that are available for your monitor. The following steps can be done to select monitor type. This section applies only after installation, or when a different monitor is used. 1. Open the OS/2 System folder. 2. Open the System Setup folder. 3. Open the System object. 4. When the System - Settings notebook appears, select the Screen tab. This will take you to page 2 of the settings. 5. On Screen page 2, select your monitor type from the Display Name list. If your monitor is not listed, select DEFAULT. Return to Screen page 1. It may be necessary to restart your system to have all refresh rate options available. Selecting Screen Resolution/Refresh Rate To switch to a different video resolution, color depth or refresh rate, follow the steps below. 1. Open the OS/2 System folder. 2. Open the System Setup folder. 3. Open the System object. 4. From the selection windows provided, select a new Screen Resolution and Screen refresh rate. Please note, Refresh rates, other than 60Hz, are only valid when the display is switched to CRT only display mode. 5. Close the System-Settings notebook. 6. Perform a shutdown and restart for the changes to take effect. Chapter 5 PCI VGA Setup 63 Installation Notes 1. During the installation of this driver, DISPLAY.LOG and DSPINSTL.LOG files are created in \OS2\INSTALL directory. These files identify the OS/2 system files that were updated, and indicate whether the installation was successful. The DISPLAY.LOG file also contains a string that identifies the version of driver that was installed. This information may be important when reporting an installation problem. 2. During installation, DSPINSTL will invoke the SVGA Configuration program SVGA.EXE to determine the hardware configuration, and create the file \OS2\INSTALL\SVGADATA.PMI. If this file is not created, the adapter will not be supported. When this step is done, the display will be blanked, and you may see a series of flashes on the display and/or what appears to be a "corrupted" display. This is normal, as the configuration process is doing Video BIOS mode sets to determine which screen resolutions BIOS supports. This configuration information is then used to provide the System-Settings Resolution and Refresh selections. 64 PCM-5862E/EL User's Manual 6 Audio Setup The PCM-5862E/5862EL is equipped with an audio interface that records and playback CD-quality audio. This chapter provides instructions for installing the software drivers on the included audio driver diskettes. Chapter 6 Audio Setup CHAPTER 65 Introduction The PCM-5862E/5862EL on board audio interface provides highquality stereo sound and FM music synthesis (ESFM) by using the ES1868 or ES1869 audio controller from ESS Technology, Inc. The audio interface can record, compress, and play back voice, sound, and music with built-in mixer control. The PCM-5862E/5862EL on board audio interface also supports the Plug and Play (PnP) standard and provides PnP configuration for the audio, FM, and MPU-104 logical devices. It is compatible with Sound BlasterTM; Sound Blaster ProTM version 3.01, voice and music functions. The ESFM synthesizer is register compatible with the OPL3 and has extended capabilities. DOS Utilities The ES1868/1869 audio controller supports PC games and applications for Sound BlasterTM and Sound BlasterTM with no needs of device driver in DOS environment. The default setting for audio controller in DOS are listed as follows. Address : 220H IRQ DMA :9 :1 MPU-401 : Disabled Changing setting in DOS The audio controller setting can be changed in DOS environment by using the DOS SETUP utility located in the UTILITY subdirectory of audio driver diskette. To change the setting, simply type the DOSSET at the DOS prompt. Follow the instructions on screen to choose the new setting for the ES1868/1869 audio controller. 66 PCM-5862E/EL User's Manual Controlling volume in DOS The ES1868/1869 audio controller provides software control on the setting of audio volumes. The VOLUME CONTROL utility located in the UTILITY subdirectory of audio driver diskette is used to control the volume setting in DOS. To control the volume setting, simply type the ESSVOL at the DOS prompt with appropriate parameters. The syntex of ESSVOL is shown as follows. ESSVOL [/?] [/v:xx] [/l:xx] [/w:xx] [/m:xx] [/c:xx] [/s:xx] [/ a:xx] no option /? /v /l /w /m /c /s /a /p xx Display all volume settings. Display this message. Change master volume. Change line volume. Change wave volume. Change microphone volume. Change CD volume. Change Synthesizer volume. Change AuxB volume. Change PC Speaker volume. Volume. Note: no xx means 0 The value range of volume is 0 - 15. [PC Speaker volume range is 0 - 7] Chapter 6 Audio Setup 67 Driver Installation Before you begin To facilitate the installation of the audio drivers, you should read the instructions in this chapter carefully before you attempt installation. The audio drivers for the PCM-5862E/5862EL board are located on the audio driver diskettes. You must install the drivers by using the supplied SETUP program. Note: The files on the software installation diskette are compressed. Do not attempt to install the drivers by copying the files manually. You must use the supplied SETUP program to install the drivers. Windows 3.1 drivers These drivers are designed to work with Microsoft Windows 3.1. You may install these drivers through Windows. 1. Run Windows to make sure that it is working correctly. 2. Place the audio driver diskette in drive A. In the Windows Program Manager, choose File from the Options Menu. Then from the pull-down menu, choose Run . . . . At the command line prompt, type A:\WIN31\SETUP. Press the 68 PCM-5862E/EL User's Manual Windows 95 Drivers 1. Boot your system and place the audio driver diskette in drive A. 2. Select Add New Hardware from Windows`s Control Panel. 3. Click Next to bring up the Windows search for new hardware setup screen. 4. Select No and click Next button. 4. Select Sound, video and game controllers from the Hardware types list and click Next button. 5. Click Have Disk, type A:\WIN95 and press Chapter 6 Audio Setup 69 70 PCM-5862E/EL User's Manual APPENDIX A Programming the Watchdog Timer The PCM-5862E/5862EL is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for whatever reason. This feature ensures system reliability in industrial standalone, or unmanned, environments. Chapter 1 General Information 71 Programming the Watchdog Timer In order to program the watchdog timer, you must write a program which writes I/O port address 443 (hex). The output data is a value of time interval. The value range is from 01(hex) to 3F(hex), and the related time interval is 1 sec. to 63 sec. Data 01 02 03 04 Time Interval 1 sec. 2 sec. 3 sec. 4 sec. . . . 63 sec. 3F After data entry, your program must refresh the watchdog timer by rewriting the I/O port 443 (hex) while simultaneously setting it. When you want to disable the watchdog timer, your program should read I/O port 443 (hex). The following example shows how you might program the watchdog timer in BASIC: 10 20 30 40 50 60 70 80 REM Watchdog timer example program OUT &H443, data REM Start and restart the watchdog GOSUB 1000 REM Your application task #1 OUT &H443, data REM Reset the timer GOSUB 2000 REM Your application task #2 OUT &H443, data REM Reset the timer X=INP (&H043) REM Disable the watchdog timer END 1000 REM Subroutine #1, you application task . . . 1070 RETURN 2000 REM Subroutine #2, you application task . . . 2090 RETURN 72 PCM-5862E/EL User's Manual Installing PC/104 Modules This appendix gives instructions for installing PC/104 modules. Appendix B Installing PC/104 Modules APPENDIX B 73 B.1 Installing PC/104 modules The PCM-5862E/5862EL's PC/104 connectors give you the flexibility to attach PC/104 modules. Installing these modules on the PCM-5862E/5862EL is quick and simple. The following steps show how to mount the PC/104 modules: 1. Remove the PCM-5862E/5862EL from your system paying particular attention to the safety instructions already mentioned above. 2. Make any jumper or link changes required to the CPU card now. Once the PC/104 module is mounted you may have difficulty in accessing these. 3. Normal PC/104 modules have male connectors and mount directly onto the main card. (Refer to the diagram on the following page.) 4. Mount the PC/104 module onto the CPU card by pressing the module firmly but carefully onto the mounting connectors. 5. Secure the PC/104 module onto the CPU card using the four mounting spacers and screws. 74 PCM-5862E/EL PC/104 Mounting Support Female Male PCA-6154/L PC/104 module Figure B-1: PC/104 module mounting diagram 8.9 95.9 90.8 82.5 6.4 3.2 90.8 5.1 0 5.1 0 85.1 5.1 90.2 Figure B-2: PC/104 module dimensions (mm) (0.1) Appendix B Installing PC/104 Modules 75 76 PCM-5862E/EL APPENDIX C Pin Assignments This appendix contains information of a detailed or specialized nature. It includes: * * * * * * * * * * * * * * * * * * * * * * * CRT display connector Flat panel display connector PC/104 connectors USB connectors Fan power connector Front panel connector CD audio connector Peripheral power connector Ethernet 10BASE-T connector IR connector Audio connector Main power connector ATX power control connector ATX power control connector Keyboard and mouse connector COM port connector IDE hard drive connector Floppy drive connector Parallel port connector IRQ mapping chart System I/O ports 1st memory map DMA channel assignment Appendix C Pin Assignments 77 CRT display connector (CN1) 15 13 11 9 7 5 3 1 16 14 12 10 8 6 4 2 PCM-5862E/5862EL CRT display connector Pin 1 2 3 4 5 6 7 8 Signal RED N/C GREEN SIGNAL GND BLUE N/C N/C N/C Pin 9 10 11 12 13 14 15 16 Signal SIGNAL GND H-SYNC CHASSIS GND V-SYNC CHASSIS GND N/C CHASSIS GND N/C 78 PCM-5862E/EL User's Manual Flat panel display connector (CN2) 2 4 * * * * * 42 44 1 3 * * * * * 41 43 PCM-5862E/5862EL Flat panel display connector Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 Function +12 V GND 5V/3.3V ENAVEE* P0 P2 P4 P6 P8 P10 P12 P14 P16 P18 P20 P22 GND SHFCLK M GND GND ENAVDD* Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 Function +12 V GND 5V/3.3V GND P1 P3 P5 P7 P9 P11 P13 P15 P17 P19 P21 P23 GND FLM LP ENABKL* ASHFCLK 5V/3.3V * Low active Appendix C Pin Assignments 79 PC/104 connectors (CN3, CN9) CN3 1 Row A Row B 1 2 * * * * * 31 32 2 * * * * * 31 32 CN9 1 Row C Row D 1 2 * * * * * 19 20 2 * * * * * 19 20 PCM-5862E/5862EL PC/104 connectors Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Signal (CN3) RowA RowB IOCHCHK* SD7 SD6 SD5 SD4 SD3 SD2 SD1 SD0 IOCHRDY AEN SA19 SA18 SA17 SA16 SA15 SA14 0V RESET +5V IRQ9 -5V DRQ2 -12V ENDXFR* +12 (KEY) SMEMW* SMEMR* IOW* IOR* DACK3* DRQ3 DACK1* Signal (CN9) RowA RowB 0V SBHE* LA23 LA22 LA21 LA20 LA19 LA18 LA17 MEMR* MEMW* SD8 SD9 SD10 SD11 SD12 SD13 0V MEMCS16* IOCS16* IRQ10 IRQ11 IRQ12 IRQ15 IRQ14 DACK0* DRQ0 DACK5* DRQ5 DACK6* DRQ6 DACK7* DRQ7 +5V 80 PCM-5862E/EL User's Manual PCM-5862E/5862EL PC/104 connectors (cont.) Pin Number 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Signal (CN3) RowA RowB SA13 SA12 SA11 SA10 SA9 SA8 SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 0V DRQ1 REFRESH* SYSCLK IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 DACK2* TC BALE +5V OSC 0V 0V Signal (CN9) RowA RowB SD14 SD15 (KEY) -- -- -- -- -- -- -- -- -- -- -- -- MASTER* 0V 0V -- -- -- -- -- -- -- -- -- -- -- -- * Low active Appendix C Pin Assignments 81 USB connectors (CN4, CN5) 4 3 2 1 PCM-5862E/5862EL USB connector Pin 1 2 3 4 Signal +5 V UVUV+ GND Fan power connector (CN6) 3 2 1 PCM-5862E/5862EL Fan power connector Pin 1 2 3 Signal +5 V GND +12 V 82 PCM-5862E/EL User's Manual Front panel connector (CN7) 1 3 5 7 2 4 6 8 PCM-5862E/5862EL Front panel connector Pin 1 2 3 4 5 6 7 8 Signal HDD LED- (HARD DISK ACTIVE) HDD LED+ (VCC) SPEAKER+ SPEAKER- (GND) GND WATCHDOG OUTPUT* RESET SWITCH- (GND) RESET SWITCH+ * Low active Appendix C Pin Assignments 83 CD audio connector (CN8) 4 3 2 1 PCM-5862E/5862EL CD audio connector Pin 1 2 3 4 Signal CD AUDIO L GND CD AUDIO R GND Peripheral power connector (CN10) 1 2 3 4 PCM-5862E/5862EL Peripheral power connector Pin 1 2 3 4 Function GND -5 V GND -12 V 84 PCM-5862E/EL User's Manual Ethernet 10BASE-T connector (CN11) 9 7 5 3 1 10 8 6 4 2 PCM-5862E/5862EL Ethernet 10BASE-T connector Pin 1 2 3 4 5 6 7 8 9 10 Signal VCC CRS LED RCV+ RCVBNC LED GND N/C GND XMT+ XMT- IR connector (CN12) 5 4 3 2 1 PCM-5862E/5862EL IR connector Pin 1 2 3 4 5 Signal VCC NC IR IN GND IR OUT Appendix C Pin Assignments 85 Audio connector (CN13) 15 13 11 9 7 5 3 1 16 14 12 10 8 PCM-5862E/5862EL audio connector 6 4 2 Pin 1 3 5 7 9 11 13 15 Signal SPEAKER OUT R+ SPEAKER OUT L+ LINE OUT R GND LINE IN R GND NC MIC IN Pin 2 4 6 8 10 12 14 16 Signal SPEAKER OUT RSPEAKER OUT LLINE OUT L GND LINE IN L GND NC GND Main power connector (CN14) 4 3 2 1 PCM-5862E/5862EL Main power connector Pin 1 2 3 4 Signal +12 V GND GND +5 V 86 PCM-5862E/EL User's Manual Keyboard and PS/2 mouse connector (CN15) 1 2 3 4 5 6 7 8 PCM-5862E/5862EL Keyboard and mouse connector Pin 1 2 3 4 5 6 7 8 Signal GND MS VCC MS DATA MS CLOCK GND KB VCC KB DATA KB CLOCK Appendix C Pin Assignments 87 COM port connector (CN16) 39 37 * * * * * 3 1 40 39 * * * * * 4 2 PCM-5862E/5862EL COM port connector Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal RLSD1 RX1 TX1 DTR1 GND RLSD2 RX2 TX2 DTR2 GND RLSD3 RX3 TX3 DTR3 GND RLSD4 RX4 TX4 DTR4 GND Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Signal DSR1 RTS1 CTS1 RI1 NC DSR2 RTS2 CTS2 RI2 NC DSR3 RTS3 CTS3 RI3 NC DSR4 RTS4 CTS4 RI4 NC 88 PCM-5862E/EL User's Manual Note: The cable of serial port (CN16) comes with four DSUB9 male connectors. The pin assignments of each DSUB9 connector are listed below for your reference: DSUB-9 Conn.(RS-232) mode RS-422 mode RS-485 module Pin 1 2 3 4 5 6 7 8 9 Signal DCD RxD TxD DTR GND DSR RTS CTS RI Signal TXTX+ RX+ RXGND NC NC NC NC Signal DATADATA+ NC NC GND NC NC NC NC Appendix C Pin Assignments 89 IDE hard drive connector (CN17) 44 42 * * * * * 4 2 43 41 * * * * * 3 1 PCM-5862E/5862EL IDE hard drive connector Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 38 39 41 43 90 Signal IDE RESET* DATA 7 DATA 6 DATA 5 DATA 4 DATA 3 DATA 2 DATA 1 DATA 0 SIGNAL GND HDD 0 IO WRITE IO READ HD READY HDACK 0* IRQ14 ADDR 1 ADDR 0 Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 Signal GND DATA 8 DATA 9 DATA 10 DATA 11 DATA 12 DATA 13 DATA 14 DATA 15 N/C GND GND GND N/C GND N/C N/C ADDR 2 HARD DISK SELECT 0* HARD DISK SELECT 1* IDE ACTIVE* VCC GND 40 42 44 GND VCC N/C * Low active PCM-5862E/EL User's Manual Floppy drive connector (CN18) 34 32 * * * * * 4 2 33 31 * * * * * 3 1 PCM-5862E/5862EL Floppy drive connector Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 Signal GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 Signal DENSITY SELECT* N/C DRIVE TYPE INDEX* MOTOR 0* DRIVE SELECT 1* DRIVE SELECT 0* MOTOR 1* DIRECTION* STEP* WRITE DATA* WRITE GATE* TRACK 0* WRITE PROTECT* READ DATA* HEAD SELECT* DISK CHANGE* * Low active Appendix C Pin Assignments 91 Parallel port connector (CN19) 26 24 * * * * * 4 2 25 26 * * * * * 3 1 PCM-5862E/5862EL Parallel port connector Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 Signal STROBE* D0 D1 D2 D3 D4 D5 D6 D7 ACK* BUSY PE SLCT Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 Signal AUTOFD* ERR INIT* SLCTINI* GND GND GND GND GND GND GND GND N/C * Low active 92 PCM-5862E/EL User's Manual ATX Power Feature Connector (CON1) PCM-5862E/5862EL ATX Feature Connector Pin 1 2 3 Signal VPSON N.C. 5VSB (stand by voltage) ATX Soft Power Switch Connector (CON2) PCM-5862E/5862EL ATX Soft Switch Connector Pin 1 2 Signal GND SWITCH Appendix C Pin Assignments 93 System I/O Ports PCM-5862E/5862EL System I/O ports Addr. range (Hex) 000-01F 020-021 022-023 040-05F 060-06F 070-07F 080-09F 0A0-0BF 0C0-0DF 0F0 0F1 0F8-0FF 1F0-1F8 200-207 278-27F 2E8-2EF 2F8-2FF 300-31F 360-36F 378-37F 380-38F 3A0-3AF 3B0-3BF 3C0-3CF 3D0-3DF 3E8-3EF 3F0-3F7 3F8-3FF 443 Device DMA controller Interrupt controller 1, master Chipset address 8254 timer 8042 (keyboard controller) Real-time clock, non-maskable interrupt (NMI) mask DMA page register, Interrupt controller 2 DMA controller Clear math co-processor Reset math co-processor Math co-processor Fixed disk Game I/O Reserved Serial port 4 Serial port 2 Prototype card Reserved Parallel printer port 1 (LPT 2) SDLC, bisynchronous 2 Bisynchronous 1 Monochrome display and printer adapter(LPT1) Reserved Color/graphics monitor adapter Serial port 3 Diskette controller Serial port 1 Watchdog timer * PNP audio I/O map range from 220 ~ 250H (16 bytes) MPU-401 select from 300 ~ 330H (2 bytes) 94 PCM-5862E/EL User's Manual 1st MB Memory Map PCM-5862E/5862EL 1st MB memory map Addr. range (Hex) F000h - FFFFh DC00h - EFFFh *CC00h - DBFFh C000h - CBFFh B800h - BFFFh B000h - B7FFh A000h - AFFFh 0000h - 9FFFh Device System ROM Unused Ethernet ROM Expansion ROM CGA/EGA/VGA text Unused EGA/VGA graphics Base memory * If Ethernet Boot ROM enabled DMA Channel Assignments PCM-5862E/5862EL DMA channel assignments Channel 0 1 2 3 4 5 6 7 Function Available Available (Audio) Floppy disk (8-bit transfer) Available (Parallel Port) Cascade for DMA controller 1 Available Available Available * Audio DMA select 0, 1 or 3 ** Parallel Port DMA select 1 or 3 Appendix C Pin Assignments 95 IRQ mapping chart PCM-5862E/5862EL IRQ mappingg ch5862E/5862ELction 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 5862E/5862ELer Keyboard Interrupt from Controller 2 COM2 COM1 COM4 FDD LPT1 RTC Reserved (Audio) COM3 Reserved (Ethernet) PS/2 mouse INT from co-processor Primary IDE Watchdog Timer * Ethernet interface IRQ select: 9, 11, 12, 15 * PnP audio IRQ select: 9, 11, 12, 15 * PnP USB IRQ select: 9, 11, 12, 15 96 PCM-5862E/EL User's Manual APPENDIX D Optional Extras Appendix D Optional Extras 97 PCM-10586-2 Cable kit for PCM-5862E/5862EL The PCM-5862E/5862EL requires several cables for normal operation. You can make them yourself or purchase an optional cable kit assembly, which includes the following: Part No. Cable Description PCM-5862EL Connector CN17 Terminating Connector 1701440350 2.5" and 1.8" IDE, IDC44P/IDC 44P /IDC44P 3.5" IDE (40P), IDC 40P/IDC 40P /Housing 44P 44-pin, 2mm, female IDC(350mm) 1701440500 CN17 40-pin, 2.54mm, female IDC(500mm) 1701340700 Dual Floppy, 3.5" and 5.25"(34p) 1701260301 1701100200 1701150150 1700060200 Parallel Port Network, 10-Base-T VGA CRT Keyboard and PS/2 mouse Peripheral power (-5V and -12V) LCD Cable CN18 34-pin Dual Floppy CN19 CN11 CN1 CN15 25-pin female DSUB RJ45 8-pin modular jack 15-pin DSUB 5-pin circular DIN, 6-pin circular DIN (4-conductor) (300mm) 44-pin, 2mm, pitch(300)mm (8-conductor pigtail) 40-pin, 9pin male DSUB x4 O - 3.5mm, female phone jack x3 1703040300 CN14 1701440303 CN2 1701080300 1700400000 1700160000 Front Panel COM 1-4 cable Audio cable CN7 CN16 CN13 98 PCA-582E/EL User's Manual Optional LCD Cables for 9.4" MONO, 10.4" TFT LCD Panel Optional LCD Cables for 9.4" MONO, 10.4" TFT LCD Panel Part No. 1700090501 1700090403 1703440151 Cable Discription Cable DF9 (2 mm) 50 cm Cable DF9 (2 mm) 40 cm Wire 30P/44P 15 cm Panel Type Toshiba LTM10C042 Sharp LM64183P Sharp LM64P89 Toshiba LTM12C275A Optional USB cable Optional USB cable part no: 1700080170 Appendix D Optional Extras 99 100 PCA-582E/EL User's Manual |
Price & Availability of PCM5862E
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |