View MCR006_366320.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MCR006
Resistors
Thick film rectangular
MCR006 (0201 size : 1 / 20W)
Features 1) Extremely small light Area ratio is 60% smaller than that of chip 1005, while weight ratio has been cut 80%. 2) Highly reliable chip resistor Ruthenium oxide dielectric offers superior resistance to the elements. 3) Electrodes not corroded by soldering Thick film makes the electrodes very strong. 4) Flat surface further facilitates mounting 5) ROHM resistors have approved ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it.
Ratings
Item Rated power Conditions Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70C.
100 80
POWER LOAD (%)
Specifications 0.05W (1 / 20W) at 70C
60 40 20 0 -55
0
70
100
125
AMBIENT TEMPERATURE (C)
Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) P: Rated power (W) R: Nominal resistance ()
E= PxR Nominal resistance Operating temperature See Table 1.
Limiting element voltage
25V
-55C to +125C
1/5
MCR006
Resistors
Jumper type Resistance Rated current Max. 100m 0.5A
Table 1 Resistance tolerance J (5%) F (1%) Resistance range () 10R10M (E24) Resistance temperature coefficient (ppm / C) 250 250
Operating temperature -55C to +125C
100R10M (E24)
Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high- level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
Characteristics
Item Resistance Guaranteed value Resistor type Jumper type J : 5% F : 1% See Table.1 (2.0%+0.1) Max. 100m Test conditions (JIS C 5201-1) JIS C 5201-1 4.5
Variation of resistance with temperature Overload
Max. 100m
JIS C 5201-1 4.8 Measurement : +20 / -55 / +20 / +125C JIS C 5201-1 4.13 Rated voltage (current) x2.5, 2s. Limiting Element Voltagex2 : 50V JIS C 5201-1 4.17 Rosin*Ethanol (25%WT) Soldering condition : 2355C Duration of immersion : 2.00.5s. JIS C 5201-1 4.18 Soldering condition : 2605C Duration of immersion : 101s. JIS C 5201-1 4.19 Test temp. : -55C~+125C 100cyc JIS C 5201-1 4.24 40C, 93%RH Test time : 1,000h~1,048h JIS C 5201-1 4.25.1 Rated voltage (current), 70C3C 1.5h : ON - 0.5h : OFF Test time : 1,000h~1,048h JIS C 5201-1 4.25.3 125C Test time : 1,000h~1,048h JIS C 5201-1 4.29 235C, Immersion cleaning, 50.5min. Solvent : 2-propanol JIS C 5201-1 4.33
Max. 100m
Solderability
A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. (1.0%+0.05) Max. 100m No remarkable abnormality on the appearance. (1.0%+0.05) (3.0%+0.1) Max. 100m Max. 100m
Resistance to soldering heat Rapid change of temperature Damp heat, steady state
(3.0%+0.1) Endurance at 70C (3.0%+0.1) Endurance (1.0%+0.05) Resistance to solvent
Max. 100m
Max. 100m
Max. 100m
Bend strength of the end face plating
Max. 100m (1.0%+0.05) Without mechanical damage such as breaks.
2/5
MCR006
Resistors
External dimensions (Unit : mm)
1
0.10.05
2
3
0.150.05
No.
1
Material
Thick dielectric glaze of ruthenium (only silver used for jumper) Thick film of palladium-silver for primary electrode Nickel-coated secondary electrode External electrode coated with Sn/Pb or Sn Alumina substrate Overcoating (resin)
0.230.03
0.60.03
4
2 3 4 5 6
5
6
Packaging
Reel Taping
P0 P2 D0 E A0 B0
02 04 06 08 08 06 04
0.30.03
F
W
A
B
D
02
P1
Heat crimp cover/Tape Thick paper Chip resistor Square press hole Cover tape
T
C
Label EIAJ ET-7200A compliant
Press career tape
Unit mm
W
F 3.50.05 P0 4.00.1
E 1.750.1 P1 2.00.05
A0 0.380.03 P2 2.00.05
B0 0.680.03 T Max. 0.50
(Unit : mm) A 180 0 -15 B 60 +1 0 9 C +1.0 0 D
8.00.2 D0
130.2
+0.1 1.5 0
3/5
MCR006
Resistors
Part designation
3-digit or 4-digit IEC coding system
Part No.
Nominal resistance
MCR0
0
6
YZ
P
J
Resistance tolerance
F 1% J 5% Specify "J" for jumper also.
Packaging specifications code
Part No. Code MCR006 YZP Packaging style Standard ordering unit (pcs) Paper tape 15,000
Dimensions
0.68 0.66 0.64
LENGTH (mm) WIDTH (mm)
0.38
0.31 JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs MICROMETER
THICKNESS (mm)
JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs MICROMETER
0.36 0.34 0.32 0.30 0.28 0.26 0.24
0.29 0.27 0.25 0.23 0.21 0.19 0.17
JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs MICROMETER
0.62 0.60 0.58 0.56 0.54 0.52 10 100 1k 10k 100k 1M
0.22
10
100
1k
10k
100k
1M
0.15
10
100
1k
10k
100k
1M
RESISTANCE ()
RESISTANCE ()
RESISTANCE ()
Fig.2 Dimensions (length)
Fig.3 Dimensions (width)
Fig.4 Dimensions (thickness)
Electrical characteristics
TEMPERATURE COEFFICIENT (ppm/C)
8.0 6.0
DC RESISTANCE (%)
800 600 400 JIS C 5201-1 4.8 SAMPLE SIZE : n=10pcs 20C / -55C 20C / 125C
4.0 3.0 2.0
R/R (%)
JIS C 5201-1 4.5 SAMPLE SIZE : n=20pcs 20C 65%RH
4.0 2.0 0
JIS C 5201-1 4.13 SAMPLE SIZE : n=10pcs RATED VOLTAGE x 2.5TIMES : 2s LIMITING ELEMENT VOLTAGE : 50V
200 0 -200 -400 -600 -800 10 100 1k 10k 100k 1M
1.0 0.0 -1.0 -2.0 -3.0 -4.0 10 100 1k 10k 100k 1M
- 2.0 - 4.0 - 6.0 - 8.0 10 100 1k 10k 100k 1M
RESISTANCE ()
RESISTANCE ()
RESISTANCE ()
Fig.5 Resistance
Fig.6 Variation of resistance with temperature
Fig.7 Overload
4/5
MCR006
Resistors
2.0 1.5 1.0
R/R (%)
2.0
JIS C 5201-1 4.18 SAMPLE SIZE : n=10pcs SOLDERING CONDITION : 260C 10s
4.0
1.5 1.0
R/R (%)
JIS C 5201-1 4.19 SAMPLE SIZE : n=10pcs -55C / 125C 100cyc
3.0 2.0
R/R (%)
JIS C 5201-1 4.24 SAMPLE SIZE : n=10pcs 40C 93%RH WITH NO LOAD 1000h
0.5 0.0 -0.5 -1.0 -1.5 -2.0 10 100 1k 10k 100k 1M
0.5 0 -0.5 -1.0 -1.5 -2.0 10 100 1k 10k 100k 1M
1.0 0 -1.0 -2.0 -3.0 -4.0 10 100 1k 10k 100k 1M
RESISTANCE ()
RESISTANCE ()
RESISTANCE ()
Fig.8 Resistance to soldering heat
Fig.9 Rapid change of temperature
Fig.10 Damp heat, steady state
4.0 3.0 2.0
R/R (%)
2.0
JIS C 5201-1 4.24 SAMPLE SIZE : n=10pcs 40C 93%RH WITH NO LOAD 1000h
2.0
1.5 1.0
R/R (%)
JIS C 5201-1 4.19 SAMPLE SIZE : n=10pcs -55C / 125C 100cyc
1.5 1.0
R/R (%)
JIS C 5201-1 4.29 SAMPLE SIZE : n=10pcs IPA, 5min.
1.0 0 -1.0 -2.0 -3.0 -4.0 10 100 1k 10k 100k 1M
0.5 0 -0.5 -1.0 -1.5 -2.0 10 100 1k 10k 100k 1M
0.5 0 -0.5 -1.0 -1.5 -2.0 10 100 1k 10k 100k 1M
RESISTANCE ()
RESISTANCE ()
RESISTANCE ()
Fig.11 Endurance at 70C
Fig.12 Endurance
Fig.13 Resistance to solvents
2.0 1.5 1.0
R/R (%)
JIS C 5201-1 4.33 SAMPLE SIZE : n=10pcs ENDURANCE WITH 90mm WIDTH
0.5 0.0 -0.5 -1.0 -1.5 -2.0 10 100 1k 10k 100k 1M
RESISTANCE ()
Fig.14 Bend strength of the end face plating
5/5

▲Up To Search▲

Price & Availability of MCR006

	To Download MCR006 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .