View NJW1140_321938.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NJW1140
AUDIO PROCESSOR with SRS
s GENERAL DESCRIPTION The NJW1140 is a sound processor includes all of the functions required to process the audio signal for TV, such as tone control, balance, volume, mute, and AGC functions. Also the NJW1140 performs SRS 3D Stereo which regenerates 3D surround sound with only two speakers. All of the internal status and variables are controlled by 2 I C BUS interface. s PACKAGE OUTLINE
s FEATURES q Operating Voltage 8 to 13V 2 q I C BUS Interface q Internal 6 Input Audio Selectors and Monitor Output q The AGC circuit reduces volume difference among input sources. 2 q Variable AGC Compression Level via I C (4-levels) q SRS 3D Stereo and Simulated Stereo 2 q Variable Surround Effect Level via I C q Low Noise VCA q Bi-CMOS Technology q Package Outline SOP40 s BLOCK DIAGRAM
NJW1140GK1
MONa
AGC
TONE TONE -La -Ha
OUTa
-2dB
+4.5dB
IN1a IN2a IN3a IN4a IN5a IN6a
SDA SCL CVA CVB CTH CTL CSR
SEL
VOL1 SRS 3D Stereo & Sim ulated Stereo VOL1
-2dB
TONE
VOL2
I C BUS Interface
2
AGC IN1b IN2b IN3b IN4b IN5b IN6b
SEL
TONE
VOL2 Bias GND Vcc
+4.5dB
MONb
TONETONE -Hb -Lb
OUTb
Vref
-1-
NJW1140
s PIN CONFIGURATION
Ach Input Terminal 1 Ach Input Terminal 2 Ach Input Terminal 3 Ach Input Terminal 4 Ach Input Terminal 5 Ach Input Terminal 6 Ach Monitor Output Terminal (-2dB) Surround Filter 1 No Connect No Connect
1 2 3 4 5 6 7 8 9 10
IN1a IN2a IN3a IN4a IN5a IN6a MONa SS FIL1 NC NC TONE-Ha TONE-La LINEa OUTa AGC CVa CVb SDA SCL GND
IN1b IN2b IN3b IN4b IN5b IN6b MONb SR FIL2 NC NC TONE-Hb TONE-Lb LINEb OUTb CSR CTH CTL NC Vref V+
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
Bch Input Terminal 1 Bch Input Terminal 2 Bch Input Terminal 3 Bch Input Terminal 4 Bch Input Terminal 5 Bch Input Terminal 6 Bch Monitor Output terminal (-2dB) Surround Filter 2 No Connect No Connect Bch Treble Filter Bch Bass Filter Bch Line Output Terminal (4.5dB) Bch Output Terminal (0dB) Pop Noise Reduction Filter for Surround ON/OFF Control Pop Noise Reduction Filter f or Treble Control Pop Noise Reduction Filter f or Bass Control No Connect Ref erence Voltage Terminal Pow er Supply Terminal
Ach Treble Filter 11 Ach Bass Filter Ach Line Output Terminal (4.5dB) Ach Output Terminal (0dB) AGC Filter Pop Noise Reduction Filter f or Ach Volume & Balance Pop Noise Reduction Filter f or Bch Volume & Balance I2C Bus Data Input I2C Bus Clock Input GND Terminal 12 13 14 15 16 17 18 19 20
- 2-
NJW1140
s ABSOLUTE MAXIMUM RATINGS (Ta=25C)
PARAMETER Supply Voltage Power Dissipation Operating Temperature Range Storage Temperature Range SYMBOL V
+
RATING 14 700 -20 to +75 -40 to +125
+
UNIT V mW C C
PD Topr Tstg
s ELECTRICAL CHARACTERISTICS ( Ta=25C, V =9V, Rg=600, RL=47k, Vin=100mVrms/1kHz)
PARAMETER Operating Voltage Supply Current Reference Voltage Maximum Input Voltage Maximum Output Voltage1 Maximum Output Voltage2 MON OUT Gain LINEOUT Gain Maximum Gain Minimum Gain Channel Balance Balance Level A-A Balance Level A-B Balance Level B-B Balance Level B-A Total Harmonic Distortion Input Selector Cross Talk Channel Separation Output Noise 1 Output Noise 2 Output Noise 3 Output Noise 4 SYMBOL V
+
TEST CONDITION
MIN. 8.0
TYP. 9.0 13 4.5 3.0 2.5 2.5 -2.0 4.5 0.0 0.0 0.0 0.0 -90 (31.6) -106 (5.0) -85 (56.2) -101 (8.9)
MAX. 13.0 25 5.0 6.5 2.0 -70 1.5 2.0 -70 2.0 -70 0.5 -70 -70 -85 (56.2) -96 (15.8) -80 (100) -91 (28.2)
UNIT V mA V Vrms Vrms Vrms dB dB dB dB dB dB dB dB dB % dB dB dBV (Vrms) dBV (Vrms) dBV (Vrms) dBV (Vrms)
ICC VREF VIM VOM1 VOM2 GVMON GVLINE GVMAX GVMIN GCB BALAA BALAB BALBB BALBA THD CT CS VNO1 VNO2 VNO3 VNO4
No Signal No Signal VOL=-20dB, THD=1% OUTPUT VOL=0dB, THD=1% LINEOUT VOL=0dB, THD=1% MON OUT LINEOUT, VOL=0dB VOL=0dB VOL=Mute, Vin=1Vrms BW=400Hz to 30kHz VOL=0dB CHS="0",BAL="11111" CHS="1",BAL="11111" Vin = 1Vrms BW=400Hz to 30kHz CHS="1",BAL="11111" CHS="0",BAL="11111" Vin = 1Vrms BW=400Hz to 30kHz Vo=0.5Vrms BW=400Hz to 30kHz Vin=1Vrms BW=400Hz to 30kHz Vin=1Vrms BW=400Hz to 30kHz VOL=0dB BW=400Hz to 30kHz VOL=Mute BW=400Hz to 30kHz LINEOUT, VOL=0dB BW=400Hz to 30kHz LINEOUT, VOL=Mute BW=400Hz to 30kHz
4.0 2.8 2.5 -2.0 -1.5 -2.0 -2.0 -
-3-
NJW1140
s ELECTRICAL CHARACTERISTICS ( Ta=25C, V =9V, Rg=600, RL=47k, Vin=100mVrms/1kHz) q TONE CONTROL (Tone Control-ON)
PARAMETER High Frequency Boost High Frequency Flat High Frequency Cut Low Frequency Boost Low Frequency Flat Low Frequency Cut SYMBOL HFBST HFFLT HFCUT LFBST LFFLT LFCUT TEST CONDITION TREBLE=+15dB, f=10kHz TRBE=0dB, f=10kHz TREBLE=-15dB, f=10kHz BASS=+15dB, f=100Hz BASS=0dB, f=100Hz BASS=-15dB, f=100Hz MIN. 12.5 -2.0 -17.5 12.5 -2.0 -17.5 TYP. 15.0 0.0 -15.0 15.0 0.0 -15.0 MAX. 17.5 2.0 -12.5 17.5 2.0 -12.5 UNIT dB dB dB dB dB dB
+
q SUB-TONE CONTROL (Sub-Tone Control-ON)
PARAMETER High Frequency Boost High Frequency Flat High Frequency Cut Low Frequency Boost Low Frequency Flat Low Frequency Cut SYMBOL SHFBST SHFFLT SHFCUT SLFBST SLFFLT SLFCUT TEST CONDITION SUB-TREBLE=+3dB, f=10kHz SUB-TREBLE=0dB, f=10kHz SUB-TREBLE=-3dB, f=10kHz SUB-BASS=+3dB, f=100Hz SUB-BASS=0dB, f=100Hz SUB-BASS=-3dB, f=100Hz MIN. 2.0 -2.0 -4.0 2.0 -2.0 -4.0 TYP. 3.0 0.0 -3.0 3.0 0.0 -3.0 MAX. 4.0 2.0 -2.0 4.0 2.0 -2.0 UNIT dB dB dB dB dB dB
q AGC
(AGC-ON)
PARAMETER SYMBOL AGCBST AGCFLT1 AGCFLT2 AGCFLT3 AGCFLT4 AGCCUT TEST CONDITION Vin=50mVrms Vin=300mVrms Vin=400mVrms Vin=500mVrms Vin=600mVrms Vin=2Vrms MIN. 1.5 -2.5 -2.5 -2.5 -2.5 -14 TYP. 3.5 0.0 0.0 0.0 0.0 -10 MAX. 5.5 2.5 2.5 2.5 2.5 -6.0 UNIT dB dB dB dB dB dB
AGC BOOST AGC FLAT 1 AGC FLAT 2 AGC FLAT 3 AGC FLAT 4 AGC CUT
q SIMULATED SURROUND
PARAMETER SURROUND SIM A SURROUND SIM B
(Simulated Surround-ON, f=1kHz)
SYMBOL SRSIMA SRSIMB TEST CONDITION Ain+Bin Aout Ain+Bin Bout MIN. 1.0 1.0 TYP. 3.0 3.0 MAX. 5.0 5.0 UNIT dB dB
q SRS 3D-Stereo
SRS GAIN HIGH 1 SRS GAIN HIGH 2 SRS GAIN LOW 1 SRS GAIN LOW 2 SRS GAIN HIGH 3 SRS GAIN HIGH 4
(SRS 3D Stereo-ON, f=125Hz)
SYMBOL SRSGH1 SRSGH2 SRSGL1 SRSGL2 SRSGH3 SRSGH4 TEST CONDITION Ain Aout, Mode=High Bin Bout, Mode=High Ain Aout, Mode=Low Bin Bout, Mode=Low Bin Aout, Mode=High Ain Bout, Mode=High MIN. 10.0 10.0 7.0 7.0 6.8 6.8 TYP. 12.0 12.0 9.0 9.0 8.8 8.8 MAX. 14.0 14.0 11.0 11.0 10.8 10.8 UNIT dB dB dB dB dB dB
PARAMETER
- 4-
NJW1140
s I C BUS Block CHARACTERISTICS (SDA, SCL)
PARAMETER High Level Input Voltage Low Level Input Voltage High Level Input Current Low Level Input Current Low Level Output Voltage (3mA at SDA pin) Maximum Output Current Maximum Clock Frequency Data Change Minimum Waiting Time Data Transfer Start Minimum Waiting Time Low Level Clock Pulse Width High Level Clock Pulse Width Minimum Start Preparation Waiting Time Minimum Data Hold Time Minimum Data Preparation Time Rise Time Fall Time Minimum Stop Preparation Waiting Time I C BUS Load Condition: Pull up resistance 4k (Connected to +5V) Load capacitance 200pF (Connected to GND)
2
2
SYMBOL VIH VIL IIH IIL VOL IOL fSCL tBUF tHD:STA tLOW tHIGH tSU:STA tHD:DAT tSU:DAT tR tF tSU:STO
MIN. 3.0 0 0 -3.0 4.7 4.0 4.7 4.0 4.7 5.0 250 4.0
TYP. -
MAX. 5.0 1.5 10 10 0.4 100 1.0 300 -
UNIT V V A A V mA kHz s s s s s s nS s nS s
SDA
tBUF
tR
tF
tHD:STA
SCL
tHD:STA tLOW P S
tHD:DAT
tHIGH
tSU:DAT Sr
tSU:STA
tSU:STO P
-5-
NJW1140
sTERMINAL DESCRIPTION No.
1 2 3 4 5 6 35 36 37 38 39 40
SYMBOL
IN1a IN2a IN3a IN4a IN5a IN6a IN6b IN5b IN4b IN3b IN2b IN1b
FUNCTION
Ach Input Terminal 1 Ach Input Terminal 2 Ach Input Terminal 3 Ach Input Terminal 4 Ach Input Terminal 5 Ach Input Terminal 6 Bch Input Terminal 6 Bch Input Terminal 5 Bch Input Terminal 4 Bch Input Terminal 3 Bch Input Terminal 2 Bch Input Terminal 1
EQUIVALENT CIRCUIT
VOLTAGE
20k
V+/2
80k
7 13 14 27 28 34
MONa LINEa OUTa OUTb LINEb MONb
Ach Monitor Output Terminal (-2dB) Ach Line Output Terminal (4.5dB) Ach Output Terminal (0dB) Bch Output Terminal (0dB) Bch Line Output Terminal (4.5dB) Bch Monitor Output Terminal (-2dB)
FB 50
V+/2
8
SRS/SS FIL1
Surround Filter 1
FB 22.2k
V+/2
11 30
TONE-Ha TONE-Hb
Ach Treble Filter Bch Treble Filter
FB 20k
V+/2
12k
12 29
TONE-La TONE-Lb
Ach Bass Filter Bch Bass Filter
FB 12k
V+/2
- 6-
NJW1140
sTERMINAL DESCRIPTION No. SYMBOL FUNCTION EQUIVALENT CIRCUIT VOLTAGE
12k
15
AGC
AGC Filter
400
400
0.9V
16 17
CVa CVb
Pop Noise Reduction Filter for Ach Volume & Balance Pop Noise Reduction Filter for Bch Volume & Balance
8k
V+/2
VREG 5V
18 19
SDA SCL
I C Bus Data Input 2 I C Bus Clock Input
2
4k
-
8k
SCL:GND SDA:ACK
20
GND
GND Terminal
0V
21
V+
Power Supply Terminal
GND
200k
22
Vref
Reference Voltage
V+/2
-7-
NJW1140
sTERMINAL DESCRIPTION No. SYMBOL FUNCTION EQUIVALENT CIRCUIT VOLTAGE
24 25
CTL CTH
Pop Noise Reduction Filter for Bass Control Pop Noise Reduction Filter for Treble Control
36k
V+/2
26
CSR
Pop Noise Reduction Filter for Surround ON/OFF Control
V+/2
33
SRS FIl2
Surround Filter 2
3k
V+/2
- 8-
NJW1140
s APPLICATION CIRCUIT
0.1F 0.1F
1
0.1F
IN1a IN2a IN3a IN4a IN5a IN6a MONa SRS/SS FIL1 NC NC TONE-Ha TONE-La LINEa OUTa AGC CVa CVb SDA SCL GND
IN1b IN2b IN3b IN4b IN5b IN6b MONb
40
0.1F
2
0.1F
39
0.1F
3
0.1F
38
0.1F
4
0.1F
37
0.1F
5
0.1F
36
0.1F 330nF
6
4.7F
35
4.7F
7
22nF
34
4.7k 8.2nF
8 9 10
2.2nF
SRS F IL2 33 NC NC TONE-Hb TONE-Lb 32 31
2.2nF
11
100nF
30
100nF
12
4.7F
29
4.7F
13
4.7F
LINEb 28
4.7F
14
0.33F
OUTb CSR CTH CTL NC Vref V+
27
1F
15
1F
26
1F
16
1F
25
1F
17 18 19 20
24 23
1F
22 21
22F
(NOTE) 2 1. Separate the I C bus line from the following terminals for avoiding digital noise problem.
Pin No. 8 11 Symbol SRS/SS FIL1 TONE-Ha Pin No. 12 29 Symbol TONE-La TONE-Lb Pin No. 30 33 Symbol TONE-Hb SRS FIL2
-9-
NJW1140
s DEFINITION OF I C REGISTER 2 q I C BUS FORMAT
MSB LSB MSB LSB MSB LSB
2
S
1bit
Slave Address
8bit
A
1bit
Select Address
8bit
A
1bit
Data
8bit
A
1bit
P
1bit
S: Starting Term A: Acknowledge Bit P: Ending Term
q SLAVE ADDRESS
MSB LSB
1
0
0
0
0
0
1
R/W
R/W=0: Write mode for register setting R/W=1: Not available q CONTROL REGISTER TABLE The select address sets each function (Volume, Balance, AGC, Surround, Tone Control). The auto increment function cycles the select address as follows. 00H01H02H03H04H05H00H
Select Address 00H 01H 02H 03H 04H 05H OUT SEL CHS BCB BCT BASS TREB Don't Care AGC1 AGC0 AGC Don't Care BAL BCSB BCST BIT D7 D6 D5 D4 VOL SR1 SR0 D3 D2 D1 D0
SUB-BASS SUB-TREB
q CONTROL REGISTER DEFAULT VALUE
Select Address 00H 01H 02H 03H 04H 05H BIT D7 0 0 0 0 0 0 D6 0 0 0 0 0 0 D5 0 0 0 0 0 0 D4 0 0 0 0 0 0 D3 0 0 0 0 0 0 D2 0 0 0 0 0 0 D1 0 0 0 0 0 0 D0 0 0 0 0 0 0
- 10-
NJW1140
sI C CONTROL COMMAND DESCRIPTION qMASTER VOLUME CONTROL
Select Address 00H BIT D7 D6 D5 D4 VOL D3 D2 D1 D0
2
The attenuator is consisted of both the Volume1 and Volume2. The total attenuation level is summing of each attenuation level of the Volume1 and Volume2. The attenuation for both the Volume1 and Volume2 are always synchronized to have the same attenuation levels for each other, and are not controllable independently for each other. *"VOL": Sets the total attenuation level for the both Ach and Bch (up to 84dB, 0.33dB/step) qCHANNEL BALANCE AND SURROUND MODE CONTROL
Select Address 01H BIT D7 CHS D6 D5 D4 BAL D3 D2 D1 SR1 D0 SR0
xChannel Balance Control To control the balance between Ach and Bch, the both commands "CHS" and "BAL" should be set. For example, to move a sound image to Ach-side, Bch should be attenuated with no attenuation on Ach. The command "CHS" defines the channel should be attenuate, and the command "BAL" defines the attenuation level itself. The attenuation for the balance control is consisted of the both Volume1 and Volume2, has the same structure with Master Volume Control described above. *"CHS": Defines the channel should be attenuated The channel CHS should be attenuated (D7)
Bch Ach 0 1
*"BAL": Defines the attenuation level for the specified channel with command "CHS" (up to 30dB, 1dB/Step) xSurround Mode Control *"SR1", "SR0": Surround Mode Switch Surround Mode
Surround OFF (Bypass) Simulated Surround SRS 3D-Stereo - High Mode SRS 3D-Stereo - Low Mode SR1 (D1) 0 0 1 1 SR0 (D0) 0 1 0 1
- 11 -
NJW1140
qBASS-TONE CONTROL SETTING
Select Address 02H BIT D7 BCB D6 D5 BASS D4 D3 D2 BCSB D1 D0
SUB-BASS
*"BCB": Defines the Bass-Tone Control Mode as Boost or Cut Bass Tone Control Mode
Cut Boost BCB (D7) 0 1
*"BASS": Sets the Cut or Boost level for Bass-Tone Control (up to 15dB, 1dB/Step) *"BCSB": Defines the Sub-Bass-Tone Control Mode as Boost or Cut Sub-Bass Tone Control Mode
Cut Boost BCSB (D2) 0 1
*"SUB-BASS": Sets the Cut or Boost level for Sub-Bass-Tone Control (up to 3dB, 1dB/Step) qTREBLE-TONE CONTROL SETTING
Select Address 03H BIT D7 BCT D6 D5 TREB D4 D3 D2 BCST D1 D0
SUB-TREB
*"BCT": Defines the Treble-Tone Control Mode as Boost or Cut Treble-Tone Control Mode
Cut Boost BCT (D7) 0 1
*"TREB": Sets the Cut or Boost level for Treble-Tone Control (up to 15dB, 1dB/Step) *"BCST": Defines the Sub-Treble-Tone Control Mode as Boost or Cut Sub-Treble-Tone Control Mode
Cut Boost BCST (D2) 0 1
*"SUB-TREB": Sets the Cut or Boost level for Sub-Treble-Tone Control (up to 3dB, 1dB/Step)
- 12-
NJW1140
qOUTPUT ON/OFF, INPUT SELECTOR, AGC and BBE ON/OFF CONTROL
Select Address 05H BIT D7 OUT D6 D5 SEL D4 D3 AGC1 D2 AGC0 D1 AGC D0
Don't Care
xOutput ON/OFF *"OUT": Output ON/OFF Switch Output
Output OFF (Mute) Output ON OUT (D7) 0 1
xInput Selector *"SEL": Input Selector Control
SEL Input Select IN1a and IN1b IN2a and IN2b IN3a and IN3b IN4a and IN4b IN5a and IN5b IN6a and IN6b D6 0 0 0 0 1 1 D5 0 0 1 1 0 0 D4 0 1 0 1 0 1
xAGC Control *"AGC1", "AGC0": Set the AGC Flat Level *"AGC": AGC ON/OFF Switch AGC Flat Level
300mVrms 400mVrms 500mVrms 600mVrms AGC OFF AGC1 (D3) 0 0 1 1 AGC0 (D2) 0 1 0 1 AGC (D1) 1 1 1 1 0
- 13 -
NJW1140
qMASTER VOLUME CONTROL (Select Address: 00H)
VOL Gain (dB) 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 -24 -25 -26 -27 -28 -29 -30 -31 -32 -33 -34 -35 -36 -37 -38 -39 -40 HEX FF FC F9 F6 F3 F0 ED EA E7 E4 E1 DE DB D8 D5 D2 CF CC C9 C6 C3 C0 BD BA B7 B4 B1 AE AB A8 A5 A2 9F 9C 99 96 93 90 8D 8A 87 D7 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D5 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 D4 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 0 0 0 D3 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 D2 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 D1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 D0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
- 14-
NJW1140
qMASTER VOLUME CONTROL (cont'd)
VOL Gain (dB) -41 -42 -43 -44 -45 -46 -47 -48 -49 -50 -51 -52 -53 -54 -55 -56 -57 -58 -59 -60 -61 -62 -63 -64 -65 -66 -67 -68 -69 -70 -71 -72 -73 -74 -75 -76 -77 -78 -79 -80 -81 -82 -83 -84 Mute HEX 84 81 7E 7B 78 75 72 6F 6C 69 66 63 60 5D 5A 57 54 51 4E 4B 48 45 42 3F 3C 39 36 33 30 2D 2A 27 24 21 1E 1B 18 15 12 0F 0C 09 06 03 00 D7 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D6 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D5 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 D4 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 D3 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 D2 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 D1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
- 15 -
NJW1140
qCHANNEL BALANCE CONTROL (Select Address: 01H)
BAL Gain (dB) 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 -24 -25 -26 -27 -28 -29 -30 Mute D6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D5 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 D4 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 D3 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 D2 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
- 16-
NJW1140
qBASS-TONE CONTROL (Select Address: 02H) / TREBLE-TONE CONTROL (Select Address: 03H)
BASS TREB Cut Gain (dB) 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 Boost Gain (dB) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 D6 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 D5 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 D4 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 D3 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
qSUB-BASS-TONE CONTROL (Select Address: 02H) / SUB-TREBLE-TONE CONTROL (Select Address: 03H)
SUB-BASS SUB-TREB Cut Gain (dB) 0 -1 -2 -3 Boost Gain (dB) 0 1 2 3 D1 0 0 1 1 D0 0 1 0 1
- 17 -
NJW1140
sTYPICAL CHARACTERISTICS
Supply Current vs Supply Voltage
Ta=25o C 15 16 Supply Current [mA] Supply Current [mA]
Su pply Current vs T emparature
V+=9V
10
14
12
5
10
0 0 5 10 15 Supply C urren t [H z]
8 0 50 Tem parature [ C]
o
100
Gain vs Volume Control
V+=9V, Vin(Ach)=1Vrms,f=1kHz, OUTPUT,Rg=600 0
0
G ain vs Balance Control
V +=9V, Vin=1V rms, f=1k Hz, Rg=600
-20
Gain [d B]
-20
Gain [dB]
-40
-40 Vo(Bch ) -60 75, 25, -20oC Vo(Ach ) 75, 25, -20o C
-60
75,25,-20oC
-80
-80
-100 0
-10 -20 -30 -40 -50 -60 -70 -80 MUTE Volume Control [dB]
-100 M UTE -30 -30
-20 0 -10 0 0 0 -2 -1
10 -10
20 -20 30-30
MUTE
Balance Control [d B]
Output Noise vs Volume Control
V+=9V, OUTPUT,BW=400-30kHz -60 -70 -80 Gain [dB] -90 -100 -110 Rg=600, Ta=25oC
Output Noise vs Temperature
V+=9V, Rg=600, BW=400Hz-30kHz -40
Output Noise [dBV]
-60 Vol=0dB -80
-100 Vol=MUTE
-120 0
-10 -20 -30 -40 -50 -60 -70 -80 MUTE Volume Control [dB]
-120 0 50 Temparature [ C]
o
100
- 18-
NJW1140
sTYPICAL CHARACTERISTICS
THD+N vs Input Voltage
V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT Rg=600, BW=400Hz-30kHz, Ta=25oC 100
THD+N vs Input Voltage
V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT Rg=600, BW=400Hz-30kHz, Vol=-20dB 100
10 THD+N [ % ]
-30dB THD+N [ % ]
10 25oC
1
1
-20oC
0.1
-20dB -10dB 0dB 0.1 1
0.1 75oC 0.01 0.01 0.1 1
0.01 0.01
Input Voltage [Vrms]
Input Voltage [Vrms]
THD+N vs Output Voltage
V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT BW=400Hz-30kHz, Rg=600, Ta=25oC 100
THD+N vs Output Voltage
V+=9V, Vin(Ach), f=1kHz, Vo(Ach)OUTPUT Rg=600, BW=400Hz-30kHz, Vol=0dB 100
10 THD+N [ % ] -30dB 1
10 THD+N [ % ] -20oC 1 25oC
0.1 -10dB 1 0dB
0.1 75oC 0.01 0.01 0.1 1
-20dB 0.01 0.01 0.1
Output Voltage [Vrms]
Output Voltage [Vrms]
M UT E Level vs Frequency
V+=9V, Vin(Ach)=1Vrm s, Vol=MU TE
Vo(Ach)O U TPUT, Rg=600 , Ta=25 C 120
o
Ch annel Separation vs Frequen cy
V+=9V , Vin=1Vrm s, f=1kHz, Vo=OUTP UT
o R g=600 , Vol=0 dB, Ta=25 C
100
Channel Sep aration [d B]
100 M UTE Level [d B] 80 60 40 20 0 100 1000 Frequency [Hz]
80
60 Vin(Ach)-V o(Bch ) Vin(Bch)-V o(Ach ) 40
20
10
4
0 100 1000 Freqency [H z]
10
4
- 19 -
NJW1140
sTYPICAL CHARACTERISTICS Gain vs Frequency (TONE)
V+=9V, Vin(Ach)=0.1Vrms,Gv:3dB steps 20 Vo(Ach), Rg=600, Ta=25oC
AGC Control
V+=9V, Vin(Ach+Bch), f=1kHz, Vo (Ach)OUTPUT Rg=600 , Ta=25o C 600m V
1
10 Gain [dB]
Output Voltage [Vrms]
500m V 0.1 400m V
0
300m V 0.01 OFF
-10
-20 100 1000 Frequency [Hz] 10
4
0.001 0.001
0.01
0.1
1
Input Voltage [Vrms]
AGC Attack Time (C:20pin =0.33 F) V+=9V , V in(Ach+Bch)=1Vrms,f=20kH z,Vo (Ach)OUTPUT
AGC level= 0.3V,Rg=600 ,T a=25oC 2
AGC Recovery T ime (C:20pin =0.33 F) V+=9V, Vin(Ac h+B ch)=1 Vrm s, f=10kHz,Vo (Ach)OUTPUT
AGC level= 0.3V,Rg=600 ,Ta=25o C 0.2
O utput Voltage [V]
0
O utput Voltage [V]
1
0.1
0
-1
-0.1
-2 0 2 4 6 8 10 Time [ms]
-0.2 0 100 200 300 400 500 Time [ms]
Gain vs Frequency (SRS&Simulated)
V+ =9V , V(Lch)in=0.1Vrm s,O UTP UT(Lch) Rg=600 ,Ta=25o C 15
Phase vs Frequency (Simulated)
V+=9V, Vin(A+Bch)=0.1Vrms, Rg=600, 200 150 Ta=25oC
BchOUT
10 Gain [d B]
5
SRS Gain MIN
Phase [deg]
SR S Gain MAX
100 50 0 -50 -100
AchOUT
0
Simulated (A+ B)IN -AOU T
-5 100 1000 Frequency [Hz]
10
4
100
1000 Frequency [Hz]
10
4
- 20-
NJW1140
s NOTE 1) The SRS technology right incorporated in the NJW1140 is owned by SRS Labs, a U.S. Corporation and licensed to New Japan Radio Co., Ltd. SRS is protected under U.S. and foreign patents issued and/or pending. , are trademarks of SRS Labs, Inc. in the United States and selected foreign countries. SRS and the Neither the purchase of the NJW1140, nor the corresponding sale of audio enhancement equipment conveys the right to sell commercialized recording made with any SRS technology. SRS Labs requires that all users of the NJW1140 must enter into a license agreement directly with SRS Labs if the royalty is not included in the purchase price. SRS Labs also requires any users to company with all rules and regulations as outlined in the SRS Trademark Usage Manual. For further information, please contact: SRS Labs, Inc. 2909 Daimler Street, Santa Ana, CA 92705 USA Tel: (949) 442-1070 Fax: (949) 852-1099 www.srslabs.com
2) Purchase of I C components of New Japan Radio Co., Ltd or one of its sublicensed Associated Companies 2 2 conveys a license under the Philips I C Patent Rights to use these components in an I C system, provided that 2 the system conforms to the I C Standard Specification as defined by Philips.
2
[CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights.
- 21 -

▲Up To Search▲

Price & Availability of NJW1140

	To Download NJW1140 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .