View HDMP-1638_293017.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Gigabit Ethernet Transceiver Chip with Dual Serial I/O and Differential PECL Clock Inputs Technical Data
HDMP-1638 Transceiver Features
* IEEE 802.3z Gigabit Ethernet compatible, Supports 1250 MBd Gigabit Ethernet * Based on X3T11 "10-Bit Specification" * Low Power Consumption * Transmitter and Receiver Functions Incorporated Onto a Single IC * 10 mm, 64-Pin Plastic Package * 5 Volt Tolerant I/Os * 10-Bit Wide Parallel TTL Compatible I/Os * Single +3.3 V Power Supply * Differential PECL Clock Inputs * Dual Serial I/O With Receive Select * 2kV ESD Protection on All Pins
Description
The HDMP-1638 transceiver is a single silicon bipolar integrated circuit packaged in a plastic QFP package. It provides a low-cost, low-power physical layer solution for 1250 MBd Gigabit Ethernet or proprietary link interfaces. It provides complete Serialize/ Deserialize ("SerDes") for copper transmission, incorporating both the Gigabit Ethernet transmit and receive functions into a single device. This chip is used to build a high speed interface (as shown in Figure 1) while minimizing board space, power and cost. It is compatible with the IEEE 802.3z specification. The transmitter section accepts 10-bit wide parallel TTL data and serializes this data into two high speed serial data streams. The parallel data is expected to be "8B/10B" encoded data, or equivalent. This parallel data is latched into the input register of the transmitter section on the rising edge of the 125 MHz reference clock (used as the transmit byte clock). The transmitter section's PLL locks to this user supplied 125 MHz byte clock. This clock is then multiplied by 10, to generate the 1250 MHz serial signal clock used to generate the high speed outputs. The high speed outputs are capable of interfacing directly to copper cables for electrical transmission or to a separate fiber optic module for optical transmission. The receiver section allows for the selection of one of two serial electrical data streams at 1250 MBd and recovers the original 10-bit wide parallel data. The receiver PLL locks onto the incoming serial signal and recovers the high speed serial clock and data. The serial data is converted back into 10-bit parallel data, recognizing the 8B/10B comma character to establish byte alignment.
Applications
* 1250 MBd Gigabit Ethernet Interface * High Speed Proprietary Interface * Backplane Serialization/Bus Extender
CAUTION: As with all semiconductor IC's, it is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by electrostatic discharge (ESD).
This Material Copyrighted By Its Respective Manufacturer
2
The recovered parallel data is presented to the user at TTL compatible outputs. The receiver section also recovers two 62.5 MHz receiver byte clocks which are 180 degrees out of phase with each other. The parallel data is properly aligned with the rising edge of alternating clocks. For test purposes, the transceiver provides for on-chip local loopback functionality controlled through an external input pin. Additionally, the byte synchronization feature may be disabled. This may be useful in proprietary applications which use alternative methods to align the parallel data.
HDMP-1638 TRANSMITTER SECTION SERIAL DATA OUT PLL PROTOCOL DEVICE
PLL RECEIVER SECTION BYTSYNC SERIAL DATA IN
REFCLK ENBYTSYNC RXSEL
Figure 1. Typical Application Using the HDMP-1638.
HDMP-1638 Block Diagram
The HDMP-1638 was designed to transmit and receive 10-bit wide parallel data over highspeed serial lines. The parallel data applied to the transmitter is expected to be encoded per the Gigabit Ethernet specification, which uses an 8B/10B encoding scheme with special reserve characters for link management purposes. In order to accomplish this task, the HDMP-1638 incorporates the following: * TTL Parallel I/O's * High Speed Phase Locked Loops * Parallel to Serial Converter * Serial Clock and Data Recovery * Comma Character Recognition * Byte Alignment Circuitry * Serial to Parallel Converter
INPUT LATCH
DATA BYTE TX[0-9]
FRAME MUX
OUTPUT SELECT INTERNAL LOOPBACK
DOUTA DOUTB
LOOPEN
TXCAP0 TXCAP1
TX PLL/CLOCK GENERATOR
INTERNAL TX CLOCKS
INPUT SELECT
DINA DINB
REFCLK RXCAP0 RXCAP1 RBC0 RBC1 RX PLL/CLOCK RECOVERY
OUTPUT DRIVER
DATA BYTE RX[0-9]
FRAME DEMUX AND BYTE SYNC
INTERNAL RX CLOCKS INPUT SAMPLER
BYTSYNC
ENBYTSYNC
RXSEL
Figure 2. HDMP-1638 Transceiver Block Diagram.
This Material Copyrighted By Its Respective Manufacturer
3
Input Latch
The transmitter accepts 10-bit wide TTL parallel data at inputs TX[0..9]. REFCLK (from this point forward, REFCLK is defined as the difference between the userprovided PECL reference clocks, REFCLK) is used as the transmit byte clock. The TX[0..9] and REFCLK signals must be properly aligned, as shown in Figure 3.
Output Select
The OUTPUT SELECT block provides for an optional internal loopback of the high speed serial signal for testing purposes. In normal operation, LOOPEN is set low and the serial data stream is placed at both DOUTA and B. When wrap-mode is activated by setting LOOPEN high, the DOUTA, B pins are held static at logic 1 and the serial output signal is internally wrapped to the INPUT SELECT box of the receiver section.
TX PLL/Clock Generator
The transmitter Phase Locked Loop and Clock Generator (TX PLL/CLOCK GENERATOR) block is responsible for generating all internal clocks needed by the transmitter section to perform its functions. These clocks are based on the supplied reference byte clock. REFCLK is used as both the frequency reference clock for the PLL and the transmit byte clock for the incoming data latches. It is expected to be 125 MHz and properly aligned to the incoming parallel data (see Figure 3). This clock is then multiplied by 10 to generate the 1250 MHz clock necessary for the high speed serial outputs.
Input Select
The INPUT SELECT block determines whether one of two pairs of signals DINA, B or the internal loop-back serial signal is used. In normal operation, LOOPEN is set low and the serial data is accepted at DINA or B. RXSEL selects if serial data at DINA or B will be parallelized. If RXSEL is low then DINA will be selected. If RXSEL is high then DINB will be selected. When LOOPEN is set high, the high speed serial signal is internally looped-back from the transmitter section to the receiver section. This feature allows for loop back testing exclusive of the transmission medium.
clocks. An automatic locking feature allows the Rx PLL to lock onto the input data stream without external PLL training controls. It does this by continually frequency locking onto the 125 MHz reference clock, and then phase locking onto the input data stream. An internal signal detection circuit monitors the presence of the input, and invokes the phase detection as the data stream appears. Once bit locked, the receiver generates the high speed sampling clock at 1250 MHz for the input sampler, and recovers the two 62.5 MHz receiver byte clocks (RBC1/RBC0). These clocks are 180 degrees out of phase with each other, and are alternately used to clock the 10-bit parallel output data.
Input Sampler
The INPUT SAMPLER is responsible for converting the serial input signal into a retimed serial bit stream. In order to accomplish this, it uses the high speed serial clock recovered from the RX PLL/CLOCK RECOVERY block. This serial bit stream is sent to the FRAME DEMUX and BYTE SYNC block.
Frame MUX
The FRAME MUX accepts the 10-bit wide parallel data from the INPUT LATCH. Using internally generated high speed clocks, this parallel data is multiplexed into the 1250 MBd serial data stream. The data bits are transmitted sequentially, from the least significant bit (TX[0]) to the most significant bit (TX[9]).
RX PLL/Clock Recovery
The RX PLL/CLOCK RECOVERY block is responsible for frequency and phase locking onto the incoming serial data stream and recovering the bit and byte
This Material Copyrighted By Its Respective Manufacturer
4
Frame Demux and Byte Sync
The FRAME DEMUX AND BYTE SYNC block is responsible for restoring the 10-bit parallel data from the high speed serial bit stream. This block is also responsible for recognizing the comma character (or a K28.5 character) of positive disparity (0011111xxx). When recognized, the FRAME DEMUX AND BYTE SYNC block works with the RX PLL/CLOCK RECOVERY block to properly align the receive byte clocks to the parallel data. When a comma character is detected and realignment of the receiver byte clocks (RBC1/RBC0) is necessary, these clocks are stretched, not slivered, to the next possible correct alignment position. These clocks will be fully aligned by the start of the second 2-byte ordered set. The second comma character received shall be aligned with the rising edge of RBC1. As per the 8B/10B encoding
scheme, comma characters must not be transmitted in consecutive bytes to allow the receiver byte clocks to maintain their proper recovered frequencies.
Output Drivers
The OUTPUT DRIVERS present the 10-bit parallel recovered data byte properly aligned to the receive byte clocks (RBC1/RBC0), as shown in Figure 5. These output data buffers provide TTL compatible signals.
Signal Detect
The SIGNAL DETECT block examines the differential amplitude of the inputs DINB. When this input signal is too small, it outputs a logic 0 at SIG_DET (refer to SIG_DET pin definition for detection thresholds). When the signal at DINB is of a valid amplitude, SIG_DET is set to logic 1.
HDMP-1638 (Transmitter Section) Timing Characteristics TA = 0 C to +70 C, VCC = 3.15 V to 3.45 V
Symbol Parameter Setup Time Hold Time Transmitter Latency Units nsec nsec nsec bits Min. 1.5 1.0 3.5 4.4 Typ. Max.
t setup thold t_txlat[1]
Note: 1. The transmitter latency, as shown in Figure 4, is defined as the time between the latching in of the parallel data word (as triggered by the rising edge of the transmit byte clock, REFCLK) and the transmission of the first serial bit of that parallel word at either output pair (defined by the rising edge of the first bit transmitted).
This Material Copyrighted By Its Respective Manufacturer
5
REFCLK
0.0 V AC
2.0 V TX[0]-TX[9] DATA DATA DATA DATA DATA 0.8 V tSETUP tHOLD
Figure 3: Transmitter Section Timing.
DATA BYTE A
DATA BYTE B
DOUTA,B
T6
T7
T8
T9
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T0
T1
T2
T3
T4
T5
t_TXLAT
TX[0]-TX[9]
DATA BYTE B
DATA BYTE C
REFCLK
0.0 V AC
Figure 4: Transmitter Latency.
This Material Copyrighted By Its Respective Manufacturer
6
HDMP-1638 (Receiver Section) Timing Characteristics TA = 0 C to +70 C, VCC = 3.15 V to 3.45 V
Symbol f_lock b_sync[1,2] t valid_before tvalid_after t duty tA-B[4] t _rxlat[3] Parameter Frequency Lock at Powerup Bit Sync Time Time Data Valid Before Rising Edge of RBC Time Data Valid After Rising Edge of RBC RBC Duty Cycle Rising Edge Time Difference Between RBC0 and RBC1 Receiver Latency Units s bits nsec nsec % nsec nsec bits 2.5 1.5 40 7.5 22.4 28.0 60 8.5 Min. Typ. Max. 500 2500
Notes: 1. This is the recovery time for input phase jumps, per the Fibre Channel Specification X3.230-1994 FC-PH Standard, Sec 5.3. 2. Tested using CPLL=0.1 F. 3. The receiver latency, as shown in Figure 6, is defined as the time between receiving the first serial bit of a parallel data word (defined as the first edge of the first serial bit) and the clocking out of that parallel word (defined by the rising edge of the receive byte clock, either RBC1 or RBC0). 4. Guaranteed at room temperature.
tvalid_before tvalid_after
RBC1
1.4 V
2.0 V RX[0]-RX[9] K28.5 DATA DATA DATA DATA 0.8 V 2.0 V BYTSYNC 0.8 V
RBC0
1.4 V
tA-B
Figure 5: Receiver Section Timing
DATA BYTE C DATA BYTE D
DINA,B R5
R6
R7
R8
R9
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
R2
R3
R4
R5
t_rxlat
RX[0]-RX[9]
DATA BYTE A
DATA BYTE D
RBC1/0
1.4 V
Figure 6: Receiver Latency
This Material Copyrighted By Its Respective Manufacturer
7
HDMP-1638 (TRx) Absolute Maximum Ratings
TA = 25 C, except as specified. Operation in excess of any one of these conditions may result in permanent damage to this device. Symbol VCC VIN,TTL VIN,HS_IN IO,TTL Tstg Tj Parameter Supply Voltage TTL Input Voltage HS_IN Input Voltage TTL Output Source Current Storage Temperature Junction Temperature Units V V V mA C C -65 0 Min. -0.5 -0.7 2.0 Max. 5.0 VCC +2.8 VCC 13 +150 +150
HDMP-1638 (TRx) Guaranteed Operating Rates
Parallel Clock Rate (MHz) Min. Max. 124.0 126.0
TA = 0 C to +70 C, VCC = 3.15 V to 3.45 V Serial Baud Rate (MBaud) Min. Max. 1240 1260
HDMP-1638 (TRx) Transceiver Reference Clock Requirements TA = 0 C to +70 C, VCC = 3.15 V to 3.45 V
Symbol f Ftol Symm Parameter Nominal Frequency (for Gigabit Ethernet Compliance) Frequency Tolerance Symmetry (Duty Cycle) Units MHz ppm % -100 40 Min. Typ. 125 +100 60 Max.
This Material Copyrighted By Its Respective Manufacturer
8
HDMP-1638 (TRx) DC Electrical Specifications TA = 0 C to +70 C, VCC = 3.15 V to 3.45 V
Symbol VIH,TTL VIL,TTL VOH,TTL VOL,TTL IIH,TTL IIL,TTL ICC,TRx[1,2] Parameter TTL Input High Voltage Level, Guaranteed High Signal For All Inputs TTL Input Low Voltage Level, Guaranteed Low Signal For All Inputs TTL Output High Voltage Level, IOH = -400 A TTL Output Low Voltage Level, IOL = 1 mA Input High Current (Magnitude), VIN = 2.4 V, V CC = 3.45 V Input Low Current (Magnitude), VIN = 0.4 V, VCC = 3.45 V Transceiver VCC Supply Current, TA = 25 C Units V V V V A A ma 270 Min. 2 0 2.2 0 Typ. Max. 5.5 0.8 VCC 0.6 40 -600
Notes: 1. Masurement Conditions: Tested sending 1250 MBd PRBS 2^7-1 sequence from a serial BERT with both DOUT outputs biased with 150 resistors. 2. Typical specified with VCC = 3.3 volts, maximum specified with V CC = 3.45 volts.
HDMP-1638 (TRx) PECL DC Electrical Specifications TA = 0 C to +70 C, VCC = 3.15 V to 3.45 V
Symbol Parameter Units Min. Typ. Max. V V 2.14 1.49 2.42 1.82
VIH,PECL PECL Input High Voltage Level VIL,PECL PECL Input Low Voltage Level
This Material Copyrighted By Its Respective Manufacturer
9
HDMP-1638 (TRx) AC Electrical Specifications TA = 0 C to +70 C, VCC = 3.15 V to 3.45 V
Symbol tr,TTLin tf,TTLin tr,TTLout tf,TTLout trs,HS_OUT tfs,HS_OUT trd,HS_OUT tfd,HS_OUT VIP,HS_IN VOP,HS_OUT[1] Parameter Input TTL Rise Time, 0.8 to 2.0 Volts Input TTL Fall Time, 2.0 to 0.8 Volts Output TTL Rise Time, 0.8 to 2.0 Volts, 10 pF Load Output TTL Fall Time, 2.0 to 0.8 Volts, 10 pF Load HS_OUT Single-Ended (+DOUT) Rise Time HS_OUT Single-Ended (+DOUT) Fall Time HS_OUT Differential Rise Time HS_OUT Differential Fall Time HS_IN Input Peak-To-Peak Differential Voltage HS_OUT Output Pk-Pk Diff. Voltage (Z0=50 , Fig. 10) Units nsec nsec nsec nsec psec psec psec psec mV mV 85 85 85 85 200 1200 1200 1600 Min. Typ. 2 2 1.5 1.1 225 200 2.4 2.4 327 327 327 327 2000 2200 Max.
Note: 1.Output Peak-to-Peak Differential Voltage specified as DOUT+ minus DOUT-.
22.0680 ns A. DIFFERENTIAL HS_OUT OUTPUT (DOUT+ MINUS DOUT-)
Yaxis = 400 mV/DIV
22.0680 ns B. SINGLE-ENDED HS_OUT OUTPUT (DOUT+)
Yaxis = 200 mV/DIV
Eye Diagrams of the High-Speed Serial Outputs from the HDMP-1638 as Captured on the 83480A Digital Communications Analyzer. Tested with PRBS=2 7-1. Figure 7: Transmitter DOUT Eye Diagrams.
This Material Copyrighted By Its Respective Manufacturer
10
HDMP-1638 (Transmitter Section) Output Jitter Characteristics (Measured with equivalent parts which have TTL REFCLK input) TA = 0 C to +70 C, VCC = 3.15 V to 3.45 V
Symbol RJ[1] DJ[1] Parameter Random Jitter at DOUT, the High Speed Electrical Data Port, Specified as 1 Sigma Deviation of the 50% Crossing Point (RMS) Deterministic Jitter at DOUT, the High Speed Electrical Data Port (pk-pk) Units ps ps Typ. 8 TBD
Note: 1. Defined by Fibre Channel Specification X3.230-1994 FC-PH Standard, Annex A, Section A.4 and tested using measurement method shown in Figure 8.
70311A CLOCK SOURCE
70841B PATTERN GENERATOR
70841B PATTERN GENERATOR*
83480A OSCILLOSCOPE 125 MHz TRIGGER CH1 CH2
DIVIDE BY 10 CIRCUIT (DUAL OUTPUT)
1.25 GHz
+K28.5, -K28.5 + DATA - DATA 83480A OSCILLOSCOPE
0000011111 + DATA - DATA 1.25 GHz 70311A CLOCK SOURCE
DIVIDE BY 2 CIRCUIT
TRIGGER CH1 CH2
+DOUT BIAS TEE
-DOUT
+DOUT -DOUT VARIABLE DELAY TTL -DIN +DIN
HDMP-1638 REFCLK LOOPEN
HDMP-1638
125 MHz REFCLK Tx[0..9] ENBYTSYNC LOOPEN Rx[0..9]
* PATTERN GENERATOR PROVIDES A DIVIDE BY 10 FUNCTION. 1.4 V
Tx[0..9]
0011111000 (STATIC K28.7)
B. BLOCK DIAGRAM OF DJ MEASUREMENT METHOD
A. BLOCK DIAGRAM OF RJ MEASUREMENT METHOD
Figure 8: Transmitter Jitter Measurement Method.
This Material Copyrighted By Its Respective Manufacturer
11
HDMP-1638 (TRx) Thermal and Power Temperature Characteristics TA = 0 C to +70 C, VCC = 3.15 V to 3.45 V
Symbol P D, TRx[1,2] PD, TRx[1,2,3]
jc[4]
Parameter Transceiver Power Dissipation, one Output Pair Open, Parallel Data Has 5 Ones and 5 Zeroes. Transceiver Power Dissipation, Outputs Connected Per Recommended Bias Terminations with Idle Pattern Thermal Resistance, Junction to Case
Units Typ. mW mW C/W 840 890 10
Max. TBD TBD
Notes: 1. PD is obtained by multiplying VCC by ICC and subtracting the power dissipated outside the chip at the high speed bias resistors. 2. Typical specified with V CC = 3.3 volts, maximum value specified with VCC = 3.45 volts. 3. Specified with high speed outputs biased with 150 resistors and receiver TTL outputs driving 10 pF loads. 4. Based on independent package testing by Agilent Technologies. ja for these devices is 48C/W for the HDMP-1638. ja is measured on a standard 3x3" FR4 PCB in a still air environment. To determine the actual junction temperature in a given application, use the following: T J = T C +( jc x Pd), where TC is the case temperature measured on the top center of the package and P D is the power being dissipated.
I/O Type Definitions
I/O Type I-TTL O-TTL HS_OUT HS_IN C S PECL Definition Input TTL, floats high when left open Output TTL High Speed Output, ECL Compatible High Speed Input External circuit node Power supply or ground Positive ECL
HDMP-1638 (TRx) Pin Input Capacitance
Symbol Parameter CINPUT Input Capacitance on TTL Input Pins Units Typ. Max. pF 1.6
This Material Copyrighted By Its Respective Manufacturer
12
O_TTL
VCC_TTL VCC_TTL
I_TTL
R
R
VCC_TTL or VCC_RX
R
R
VBB 1.4 V R GND ESD PROTECTION ESD PROTECTION GND_TTL
GND_TTL
Figure 9: O-TTL and I-TTL Simplified Circuit Schematic.
HS OUT
VCC_TXHS VCC_TXECL VCC VCC
HS IN
+A - + - VCC R R +DOUT RPAD 150 -DOUT RPAD Zo 0.01 F GND GND ESD
PROTECTION
0.01 F Zo
+DIN
2 * Z0
-DIN
ESD
PROTECTION
150 GND_TXHS GND
NOTES: 1. HS_IN INPUTS SHOULD NEVER BE CONNECTED TO GROUND AS PERMANENT DAMAGE TO THE DEVICE MAY RESULT. 2. THE OPTIONAL SERIES PADDING RESISTORS (RPAD) HELP DAMPEN LOAD REFLECTIONS. TYPICAL RPAD VALUES FOR MISMATCHED LOADS RANGE BETWEEN 25-Z0 . 3. FOR PECL REFCLK INPUT PAIR, THE CONSTANT VOLTAGE SUPPLIES (SHOWN AS A) AND RESISTORS R ARE OMITTED.
Figure 10: HS_OUT and HS_IN Simplified Circuit Schematic.
This Material Copyrighted By Its Respective Manufacturer
13
VCC_TXHS DOUTB+ DOUTBVCC_TXECL DOUTA+ DOUTA-
VCC_RX GND_RXHS DINB+
DINBVCC_RXHS
DINAGND_RXA
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 GND_TXHS TX[0] TX[1] TX[2] TX[3] TX[4] TX[5] TX[6] TX[7] TX[8] TX[9] NC RXSEL GND_TXTTL GND_TXA TXCAP1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 48 47 46 45 44 43 RXCAP0 BYTSYNC GND_RXTTL RX[0] RX[1] RX[2] VCC_RXTTL RX[3] RX[4] RX[5] RX[6] VCC_RXTTL RX[7] RX[8] RX[9] GND_RXTTL
VCC_RXA RXCAP1
42 41 40 39 38 37 36 35 34 33
HDMP-1638 xxxx-x Rz.zz S YYWW
SIG_DET NC
DINA+
xxxx-x = WAFER LOT NUMBER-BUILD NUMBER Rz.zz = DIE REVISION S = SUPPLIER CODE YYWW = DATE CODE (YY = YEAR, WW = WORK WEEK) COUNTRY = COUNTRY OF MANUFACTURE (MARKED ON BACK OF DEVICE) *NOTE: PINS 12 AND 27 ARE DESIGNATED AS "NO CONNECT" PINS AND ARE NORMALLY UNCONNECTED.
HDMP-1638 fig 11
Figure 11: HDMP-1638 (TRx) Package Layout and Marking, Top View.
This Material Copyrighted By Its Respective Manufacturer
-REFCLK ENBYTSYNC GND
RBC0 GND_RXTTL
VCC_RXTTL RBC1
TXCAP0 VCC_TXA LOOPEN VCC_TX GND +REFCLK
VCC_RX
14
TRx I/O Definition
NAME BYTSYNC PIN 47 TYPE O-TTL SIGNAL Byte Sync Output: An active high output. Used to indicate detection of either a comma character (0011111XXX). It is only active when ENBYTSYNC is enabled. Serial Data Inputs: High speed inputs. Serial data is accepted from the DINA inputs when LOOPEN and RXSEL are both low. Serial Data Inputs: High speed inputs. Serial data is accepted from the DINB inputs when LOOPEN is low and RXSEL high. Serial Input Select: If this pin is held low then DINA inputs are parallelized. If this pin is held high then DINB inputs are parallelized. Serial Data Outputs: High speed outputs. These lines are active when LOOPEN is set low. When LOOPEN is set high, these outputs are held static at logic 1. If unused, remove the 150 pulldown resistors to save power. Serial Data Outputs: High speed outputs. These lines are active when LOOPEN is set low. When LOOPEN is set high, these outputs are held static at logic 1. If unused, remove the 150 Ohm pulldown resistors to save power. Enable Byte Sync Input: When high, turns on the internal byte sync function to allow clock synchronization to a comma character (0011111XXX). When the line is low, the function is disabled and will not reset registers and clocks, or strobe the BYTSYNC line. Logic Ground: Normally 0 volts. This ground is used for internal PECL logic. It should be isolated from the noisy TTL ground as well as possible. Analog Ground: Normally 0 volts. Used to provide a clean ground plane for the receiver PLL and high-speed analog cells. Ground: Normally 0 volts. TTL Receiver Ground: Normally 0 volts. Used for the TTL output cells of the receiver section.
-DINA +DINA
52 53
HS_IN
-DINB +DINB
55 56
HS_IN
RXSEL
13
I-TTL
-DOUTA +DOUTA
59 60
HS_OUT
-DOUTB +DOUTB
62 63
HS_OUT
ENBYTSYNC
24
I-TTL
GND
21 25
S
GND_RXA
51
S
GND_RXHS GND_RXTTL
57 32 33 46 15
S S
GND_TXA
S
Analog Ground: Normally 0 volts. Used to provide a clean ground plane for the PLL and high-speed analog cells.
This Material Copyrighted By Its Respective Manufacturer
15
NAME GND_TXHS GND_TXTTL
PIN 1 14
TYPE S S
SIGNAL Ground: Normally 0 volts. TTL Transmitter Ground: Normally 0 volts. Used for the TTL input cells of the transmitter section. These pins are connected to an isolated pad and have no functionality. They may be left open, however, TTL levels may also be applied to these pins.
N/C
27,12
LOOPEN
19
I-TTL
Loopback Enable Input: When set high, the high speed serial signal is internally wrapped from the transmitter's serial loopback outputs back to the receiver's loopback inputs. Also when in loopback mode, the DOUT outputs are held static at logic 1. When set low, DOUT outputs and DIN inputs are active. Receiver Byte Clocks: The receiver section recovers two 62.5 MHz receive byte clocks. These two clocks are 180 degrees out of phase. The receiver parallel data outputs are alternately clocked on the rising edge of these clocks. The rising edge of RBC1 aligns with the output of the comma character (for byte alignment) when detected. Reference Clock and Transmit Byte Clock: A 125 MHz clock supplied by the host system. The transmitter section accepts this signal as the frequency reference clock. It is multiplied by 10 to generate the serial bit clock and other internal clocks. The transmit side also uses this clock as the transmit byte clock for the incoming parallel data TX[0]..TX[9]. It also serves as the reference clock for the receive portion of the transceiver. Data Outputs: One 10 bit data byte. RX[0] is the first bit received. RX[0] is the least significant bit. When there is a loss of input signal at DINB and RXSEL is high, these outputs are held static at logic 1. Refer to SIG_DET (pin 26) pin definition for more details.
RBC1 RBC0
30 31
O-TTL
+REFCLK -REFCLK
22 23
PECL
RX[0] RX[1] RX[2] RX[3] RX[4] RX[5] RX[6] RX[7] RX[8] RX[9] RXCAP0 RXCAP1
45 44 43 41 40 39 38 36 35 34 48 49
O-TTL
C
Loop Filter Capacitor: A loop filter capacitor for the internal PLL must be connected across the RXCAP0 and RXCAP1 pins. (typical value = 0.1 F)
This Material Copyrighted By Its Respective Manufacturer
16
NAME TX[0] TX[1] TX[2] TX[3] TX[4] TX[5] TX[6] TX[7] TX[8] TX[9] TXCAP0 TXCAP1
PIN 2 3 4 5 6 7 8 9 10 11 17 16
TYPE I-TTL
SIGNAL Data Inputs: One 10 bit, 8B/10B encoded data byte. TX[0] is the first bit transmitted. TX[0] is the least significant bit.
C
Loop Filter Capacitor: A loop filter capacitor must be connected across the TXCAP1 and TXCAP0 pins (typical value=0.1 F). Signal Detect: Indicates a loss of signal on the high-speed differential inputs, DINB, as in the case where the transmission cable becomes disconnected. If DIN>=200 mV peak-to-peak, SIG_DET=logic 1. If DIN<200 mV and DIN>50 mV, SIG_DET=undefined. If DIN<=50 mV, SIG_DET=logic 0. Logic Power Supply: Normally 3.3 volts. Used for internal receiver PECL logic. It should be isolated from the noisy TTL supply as well as possible. Analog Power Supply: Normally 3.3 volts. Used to provide a clean supply line for the PLL and high speed analog cells. High Speed Supply: Normally 3.3 volts. Used only for the high speed receiver cell (HS_IN). Noise on this line should be minimized for best operation. TTL Power Supply: Normally 3.3 volts. Used for all TTL receiver output buffer cells.
SIG_DET
26
O-TTL
VCC_RX
28 58
S
VCC _RXA VCC _RXHS
50
S
54
S
VCC _RXTTL
29 37 42 20
S
VCC_TX
S
Logic Power Supply: Normally 3.3 volts. Used for internal transmitter PECL logic. Also used for all transmitter TTL input buffer cells. Analog Power Supply: Normally 3.3 volts. Used to provide a clean supply line for the PLL and high speed analog cells. High Speed ECL Supply: Normally 3.3 volts. Used only for the last stage of the high speed transmitter output cell (HS_OUT) as shown in Figure 10. Due to high current transitions, this VCC should be well bypassed to a ground plane. High Speed Supply: Normally 3.3 volts. Used by the transmitter side for the high speed circuitry. Noise on this line should be minimized for best operation.
VCC_TXA
18
S
VCC _TXECL
61
S
VCC_TXHS
64
S
This Material Copyrighted By Its Respective Manufacturer
17
VCC* VCC
Transceiver Power Supply Bypass and Loop Filter Capacitors
CPLLR
GND_TXHS
RXCAP0 GND_RXTTL
VCC_RXTTL
VCC
HDMP-1638
TOP VIEW VCC_RXTTL
GND_RXTTL VCC_RX VCC_RXTTL TXCAP0 VCC_TXA
VCC_TX GND
TXCAP1
GND
GND_TXTTL GND_TXA
GND_RXTTL
CPLLT
VCC
VCC* * SUPPLY VOLTAGE INTO VCC_RXA AND VCC_TXA SHOULD BE FROM A LOW NOISE SOURCE. ALL BYPASS CAPACITORS AND PLL FILTER CAPACITORS ARE 0.1 F.
If desired, bypass capacitors may be used on the power supply pins of the HDMP-1638. All bypass chip capacitors are 0.1 F. The VCC_RXA and VCC _TXA pins are the analog power supply pins for the PLL sections. The supply into these pins should be clean with minimum noise. Use of capacitors as shown in Figure 12 is mandatory for these pins. The PLL loop filter capacitors and their pin locations are also shown on Figure 12. Notice that only two capacitors are required; CPLLT for the transmitter and CPLLR for the receiver. Nominal capacitance is 0.1 F. The maximum voltage across the capacitors is on the order of 1 volt, so the capacitor can be a low voltage type and physically small. The PLL capacitors are to be placed physically close to the appropriate pins on the HDMP-1638. Keeping the lines short will prevent them from picking up any stray noise from surrounding lines or components.
VCC_TXECL
VCC_TXHS
VCC_RXHS
VCC_RX GND_RXHS
Figure 12: Power Supply Bypass.
Start Up Procedure: The transceiver startup procedure(s) and the following conditions: VCC = +3.3 V 5 % and REFCLK = 125 MHz 100 ppm. After the above conditions have been met, apply valid data using a balanced code such as 8B/10B. Frequency lock occurs within 500 s. After frequency lock, phase lock occurs within 2500 bit times.
This Material Copyrighted By Its Respective Manufacturer
GND_RXA
VCC_RXA
RXCAP1
18
Package Information
Item Package Material Lead Finish Material Lead Finish Thickness Lead Coplanarity Plastic 85% Tin, 15% Lead 300-800 m 0.08 mm max Details
Mechanical Dimensions
PIN #1
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 1 2 3 4 5 6 7 8 9 48 47 46 45 44 43 42 41 40
HDMP-1638
A1
A2
10 39 TOP VIEW 11 38 12 37 13 36 14 35 15 34 16 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
B4
B1 A1 A2 B2 B3
B5
C1
C3
C2 ALL DIMENSIONS ARE IN MILLIMETERS. PART NUMBER HDMP-1638 TOLERANCE A1 10.00 A2 13.20 B1 0.22 B2 0.50 B3 0.88 B4 0.17 B5 0.25 C1 2.00 + 0.10/ - 0.05 C2 0.25 MIN. C3 2.45 MAX.
0.10 0.25 0.05 BASIC + 0.15/ MAX. - 0.10
Figure 13: Mechanical Dimensions of HDMP-1638.
This Material Copyrighted By Its Respective Manufacturer
www.semiconductor.agilent.com Data subject to change. Copyright (c) 1999 Agilent Technologies, Inc. 5968-5120E (11/99)
This Material Copyrighted By Its Respective Manufacturer

▲Up To Search▲

Price & Availability of HDMP-1638

	To Download HDMP-1638 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .