 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| x CMOS Analog Switch x Low On-Resistance RON=100 TYP x High Speed Operation tpd=4ns TYP x Operating Voltage Range 2V~6V x Low Power Consumption 1A MAX s Applications q Palmtops q Digital Equipment s General Description The XC74UH4066M is a high speed CMOS Analog Switch manufactured using silicon gate CMOS fabrication. CMOS low power circuit operation makes high speed analog or digital signal switching opssible. As the XC74UH4066M is integrated into a mini molded, SOT-25 package, high density mounting is possible. s Features High Speed Operation: tpd=12ns TYP Low On-Resistance: RON=100 TYP Operating Voltage Range: 2V~6V Low Power Consumption: 1A MAX Space Saving Package: SOT-25 s Pin Configuration IN/OUT 1 5 VCC s Function CONT L H SWITCH OFF ON o H=High level, L=Low level OUT/IN 2 GND 3 4 CONT SOT-25 (TOP VIEW) s Logic Diagram IN/OUT OUT/IN CONT s Absolute Maximum Ratings PARAMETER Power Supply Voltage Input Voltage Output Voltage Input Diode Current Output Diode Current Output Current VCC ,GND Current Continuous Total Power Dissipation Storage Temperature Note: Voltage is all Ground standardized. Ta=25: RATINGS -0.5 ~ +7.0 -0.5 ~ VCC +0.5 -0.5 ~ VCC +0.5 20 20 25 25 200 -65 ~ +150 UNITS V V V mA mA mA mA mW : SYMBOL VCC VIN VOUT IIK IOK IOUT ICC, IGND Pd Tstg s Recommended Operating Conditions PARAMETER Supply Voltage Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time SYMBOL VCC VIN VOUT Topr tr, tf CONDITIONS 2~6 0 ~ VCC 0 ~ VCC -40 ~ +85 0 ~ 1000 (VCC=2.0V) 0 ~ 500 (VCC=4.5V) 0 ~ 400 (VCC=6.0V) UNITS V V V : ns o s DC Electrical Characteristics PARAMETER SYMBOL VCC(V) 2.0 VIH Control Input Voltage VIL 4.5 6.0 2.0 4.5 6.0 2.0 On Resistance Power Off Leakage Current Powr On Leakage Current Control Input Current Quiescent Supply Current RON IS(OFF) IS(ON) ICONT ICC 4.5 6.0 6.0 6.0 6.0 6.0 VCONT=VIH VIN=0 ~ VCC IIN/OUT=1mA VCON=VIL,VIN=VCC,VOUT=GND VCON=VIH,VIN=VCC,GND VIN=VCC or GND VIN=VCC or GND CONDITIONS Ta=25: 1.5 3.15 4.2 0.5 1.35 1.8 Ta=-40~85: 1.5 3.15 4.2 0.5 1.35 1.8 6250 250 210 1.0 1.0 1.0 10.0 A A A A V V MIN TYP MAX MIN MAX UNITS 2000 5000 100 200 60 170 0.1 0.1 0.1 1.0 s Switching Electrical Characteristics tr=tf=6ns PARAMETER SYMBOL tPLH tPHL tZL tZH tLZ tHZ VCC(V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 RL=10k Sine Wave Distortion Rate 4.5 CL=50pF Fin=1KgZ RL=600, CL=50pF --3dB Band Width 4.5 20 log 10 VOUT=-3dB VIN RL=600 Feed Through (switch off) Cross Talk (control switch) 4.5 2.0 4.5 6.0 2.0 Maximum Control Input Frequency Control Input Capacitance Switch Input/Output Capacitance Feed Through Capacitance CIN CIN/OUT CIN-OUT CPD 4.5 6.0 CL=50pF Fin=1MHZ RL=600 CL=50pF Fin=1MHZ RL=1k CL=15pF VOUT=VCC/2 25 60 75 20 30 30 5 6 0.5 13 10 10 MHz MHz MHz pF pF pF pF mV -50 dB 30 MHz 0.05 % RL=1k CL=50pF Output Disable Time RL=1k CL=50pF Output Enable Time CONDITIONS RL=10k CL=50pF Ta=25: 4 10 14 50 10 9 115 23 20 115 23 20 Ta=-40~85: 65 13 11 145 29 25 145 29 25 ns ns ns MIN TYP MAX MIN MAX UNITS Propagation Delay Time o Power Dissipation Capacitance Note: CPD is defined as the value of the internal equivalent capacitance which is derived from the operating supply current at times of 'No Load' (Refer to Typical Application Circuits). Ensure that the average operating supply current at times of 'No Load' meets the following conditions: ICC (opr)=CPD, VCC, Fin+ICC s Propagation Delay Time Waveforms 6ns 6ns VCC 90% 90% Input 50% 50% 10% 10% tTLH tTHL GND VOH 50% 50% Output VOL s Typical Application Circuit VCC Input o CONT Pulse Generator ON VCC Output GND CL= 10k CL= 50pF Note: open output when measuring supply current s Output Enable/Disable Time Waveform 6ns 6ns VCC 90% 90% 50% 10% tTHL tHZ 90% 50% 50% 10% Input GND VOH Output tZL tLZ VOL Output VOH 50% 10% VOL s Typical Application Circuit o Pulse Generator Input VCC VCC CONT VCC Output ON/OFF GND RL= 1 k CL= 50pF VCC Note: open output when measuring supply current s Sine Wave Distortion Rate VCC Input VCC/2 RL= 1 k CONT fin 10F ON GND CL= 50pF VCC Output Note: Input is Sine Wave s -3dB Band Width VCC Input CONT fin 0.1F ON GND VCC VOUT Output o RL= 1 k CL= 50pF Note: Input is Sine Wave s Feed Through VCC Input CONT OFF RL=600 GND VCC RL= 600 Output 0.1F fin CL= 50pF VCC/2 Note: Input is Sine Wave s Cross Talk Wave form 6ns 6ns VCC 90% 90% Input o 10% 10% GND Measurement Circuit Pulse Generator CONT VCC/2 ON/OFF RIN= 600 GND CL= 50pF VCC Output VCC VCC/2 RL= 600 s Maximum Control Input Frequency Waveforms 6ns 6ns VCC 90% 90% Input 10% 10% GND Output VCC/2 s Measurement Circuit Pulse Generator Input o VCC CONT VCC Output ON/OFF GND RL= 1 k CL= 50pF |
Price & Availability of XC74UH4066M
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |