View LC75410W_277524.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : ENN7027
CMOS IC
LC75410E, 75410W
Electronic Volume Controller for Car Audio Systems
Overview
The LC75410E and 75410W are electronic volume controllers that enable control of volume, balance, fader, bass/treble/mid, loudness, input switching, and input gain using only a small number of external components.
Features
* On-chip buffer amplifier cuts down number of external components * Low switching noise generated by on-chip switch through use of silicon gate CMOS process, for low switching noise when there is no signal * Low switching noise when there is a signal due to use of on-chip zero-cross switching circuit * On-chip 1/2 VDD reference voltage circuit * Controls performed with serial input (CCB)
Functions
* Volume: 0 dB to -79.5 dB in 0.5-dB steps, and - (161 positions) Balance function with separate L/R control * Fader: rear output or front output can be attenuated across 16 positions (in 1-dB steps from 0 dB to -2 dB, 2-dB steps from -2 dB to -20 dB, 10-dB steps from -20 dB to -30 dB, and -45 dB, -60 dB, -) * Bass/treble/mid: Each band can be controlled in 1-dB steps from 0 dB to 6 dB, and in 2-dB steps from 8 dB to 12 dB. * Input gain: 0 dB to +18.75 dB (1.25-dB steps) amplification is possible for the input signal. * Input switching: five input signals can be selected for Left and for Right (Four are singleended inputs and one is a differential input.) * Loudness: A tap is output from the -32 dB position of a 2 dB step volume control resistor ladder. A loudness function can be implemented by connecting an external RC circuit.
* CCB is a trademark of SANYO ELECTRIC CO., LTD. * CCB is SANYO's original bus format and all the bus addresses are controlled by SANYO.
Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
O1901RM (OT) No. 7027-1/28
LC75410E, 75410W
Package Dimensions
unit: mm 3159-QIP64E
[LC75410E]
17.2 1.0 1.0 1.6 0.8 14.0 0.35 1.6 1.0 0.15
unit: mm 3190-SQFP64
[LC75410W]
12.0 10.0 0.18
33 48 49 32
1.25
0.5
1.25
0.15
48 49
1.25
33 32
12.0
0.8
10.0 0.5
17.2
14.0
17
1.0 3.0max
1
16
15.6
0.8
0.5
0.1 0.5
0.1 2.7
1
16
1.7max
64
64
1.25
17
SANYO: QIP64E
SANYO: SQFP64
Pin Assignment
LVROUT LTOUT
32 LFIN 31 LFOUT 30 LROUT 29 LAVSS 28 TEST 27 DVSS 26 CL 25 DI 24 CE 23 MUTE 22 RAVSS 21 NC 20 TIM 19 RROUT 18 RFOUT 17 RFIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
LSELO
LF1C1
LF1C2
LF1C3
LF2C1
LF2C2
LF2C3
LF3C1
LF3C2
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
L5P 49 L5M 50 L4 51 L3 52 L2 53 L1 54 LVref 55 VDD 56 Vref 57 RVref 58 R1 59 R2 60 R3 61 R4 62 R5M 63 R5P 64
LC75410E LC75410W
LF3C3 RF3C3
LVRIN
LCOM
LTIN
LCT
RVROUT
RTOUT
RF2C3
RF3C1
RSELO
RF1C1
RF1C2
RF1C3
RF2C1
RF2C2
RF3C2
RVRIN
RCT
RCOM
RTIN
No. 7027-2/28
68k 0.1F 10F [BASS fo 100Hz] [MID fo 1kHz] [TREBLE fo 10kHz] 0.1F 0.1F 0.01F 0.01F 0.001F 0.001F 10F 220pF 10F 1F LVROUT LSELO LCT LVRIN LCOM LF1C1 LF1C2 LF1C3 LF2C1 LF2C2 LF2C3 LF3C1 LF3C2 LF3C3 LTOUT LTIN
47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 48
4.7k
+
L5P
32
49
LFIN LFOUT 10F
PA
+
L5M LVref
+
50
31 30
+
L4 LVref
LVref
51
LROUT LAVSS 29
28
PA
+
L3
52
10F TEST
27 DVSS
1F x 6 LVref
+
L2
53
+
L1
Multiplexer ZEROCROSS DET
+
54
10F
+
LVref
55
26
CL
CCB INTERFACE
CL DI 25
24 CE 23 MUTE
VDD
CONTROL CIRCUIT Multiplexer
56
DI COM CE
47F
+
Vref
57
LOGIC CIRCUIT
10F
+
RVref
58
47k
+
R1 RVref
ZEROCROSS DET NO SIGNAL TIMER
59
22
TEST 1M
21 NC 20
Equivalent Circuit Block Diagram/Sample Application Circuit
LC75410E, 75410W
+
R2 RVref
60
+
R3 RVref
61
+
TIM
19
0.033F RROUT RVref
18
PA
1F x 6
+
R4
62
+
R5M
63
RFOUT
17 RFIN
10F
PA
+
R5P
10F
64
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
RCT
RTIN
RCOM
RF1C2 RF1C1
RF1C3
RF2C1
RF3C1
RF3C2
RF3C3
RF2C2
RF2C3
RVRIN 10F 68k
1F 220pF
RSELO
RTOUT
RVROUT 10F 0.1F 4.7k
10F 0.1F
No. 7027-3/28
[BASS fo 100Hz] [MID fo 1kHz] [TREBLE fo 10kHz]
0.01F
0.001F
0.1F
0.01F
0.001F
LC75410E, 75410W
Specifications
Absolute Maximum Ratings at Ta = 25C, VSS = 0 V
Parameter Maximum supply voltage Maximum input voltage Allowable power dissipation Operating temperature Storage temperature Symbol VDD max VIN max Pd max Topr Tstg VDD All input pins Ta 85C, when mounted on board QIP64E SQFP64 Conditions Ratings 11 VSS - 0.3 to VDD + 0.3 680 800 -40 to +85 -50 to +125 Unit V V mW C C
Allowable Operating Ranges at Ta = 25C, VSS = 0 V
Parameter Supply voltage Input high-level voltage Input low-level voltage Input amplitude voltage Input pulse width Setup time Hold time Operating frequency Symbol VDD VIH VIL VIN ToW Tsetup Thold fopg CL CL, DI, CE CL, DI, CE CL VDD CL, DI, CE, MUTE CL, DI, CE, MUTE Conditions Ratings min 6.0 4.0 VSS VSS 1 1 1 500 typ max 10.5 10.5 1.0 VDD Unit V V V Vp-p s s s kHz
Electrical Characteristics at Ta = 25C, VDD = 9 V, VSS = 0 V
Parameter [Input block] Input resistance Minimum input gain Maximum input gain Step setting error L/R balance [Volume Block] Input resistance Step setting error L/R balance [Tone block] Step setting error Bass control range Mid control range Treble control range L/R balance ATerr Gbass Gmid Gtre BAL max. boost/cut max. boost/cut max. boost/cut 9 9 9 12 12 12 1.0 15 15 15 0.5 dB dB dB dB dB Rvr ATerr BAL LVRIN, RVRIN, loudness off 113 226 452 0.5 0.5 k dB dB Rin Ginmin Ginmax ATerr BAL L1 to L4, R1 to R4 L1 to L4, R1 to R4 25 -1 +16.5 50 0 +18.75 100 +1 +21 0.5 0.5 k dB dB dB dB Symbol Pin Name Conditions Ratings min typ max Unit
Continued on next page.
No. 7027-4/28
LC75410E, 75410W
Continued from preceding page.
Parameter [Fader Block] Input resistance Rfed LFIN, RFIN 0dB to -2dB Step setting error ATerr -2dB to -20dB -20dB to -30dB -30dB to -60dB L/R balance [General] Total harmonic distortion Input crosstalk L/R crosstalk Maximum attenuated output THD (1) THD (2) CT CT VIN = 0dBV, f = 1 kHz VIN = -10dBV, f = 10 kHz VIN = 1Vrms, f = 1 kHz VIN = 1Vrms, f = 1 kHz 80 80 80 90 0.004 0.006 88 88 88 95 5 7 40 CL, DI, CE, VIN = 9 V CL, DI, CE, VIN = 0 V THD = 1%, RL = 10 k flat overall, fIN = 1 kHz VIN = 0 dB, f = 1 kHz -10 2.3 45 2.8 70 10 15 45 10 0.01 0.01 % % dB dB dB dB V V mA A A Vrms dB BAL 25 50 100 0.5 1 2 3 0.5 k dB dB dB dB dB Symbol Pin Name Conditions Ratings min typ max Unit
Vomin (1) VIN = 1Vrms, f = 1 kHz VIN = 1Vrms, f = 1 kHz Vomin (2) INMUTE, fader - VN (1) VN (2) IDD IIH IIL VCL CMRR Flat overall, IHF-A filter Flat overall, 20 to 20 kHzBPF
Output noise voltage Current drain Input high-level current Input low-level current Maximum input voltage Common-mode rejection ratio
Control Timing and Data Format To control the LC75410E and LC75410W input specified serial data to the CE, CL, and DI pins. The data configuration consists of a total of 52 bits broken down into 8 address bits and 44 data bits.
CE DI CL
B0 B1 B2 B3 A0 A1 A2 A3 D0 D1 D2 D3 D4 D5 D38 D39 D40 D41 D42 D43
CE
1s min
1s 1s 1s min min min
1s min
CL
DI
1s min TDEST
No. 7027-5/28
LC75410E, 75410W Address code (B0 to A3) The LC75410E and 75410W use 8-bit address code and can be used in common with ICs that support SANYO's CCB serial bus. Address Code
(LSB) B0 1 B1 0 B2 0 B3 0 A0 0 A1 0 A2 0 A3 1 (81HEX)
Control code allocation Input Switching Control
D0 0 1 0 1 0 D1 0 0 1 1 0 D2 0 0 0 0 1 Setting L1 (R1) L2 (R2) L3 (R3) L4 (R4) L5 (R5) Setting
0 1
1 1
1 1
For IC testing: Normally not used
D3
Bit for IC testing: Normally set to 0
Input Gain Control
D4 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 D5 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 D6 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 D7 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0dB +1.25dB +2.50dB +3.75dB +5.00dB +6.25dB +7.50dB +8.75dB +10.0dB +11.25dB +12.5dB +13.75dB +15.0dB +16.25dB +17.5dB +18.75dB Operation
No. 7027-6/28
LC75410E, 75410W Volume Control (0 to -20.5dB)
D8 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 D9 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 D10 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 D11 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 D12 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 D13 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D14 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D15 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0dB -0.5dB -1dB -1.5dB -2dB -2.5dB -3dB -3.5dB -4dB -4.5dB -5dB -5.5dB -6dB -6.5dB -7dB -7.5dB -8dB -8.5dB -9dB -9.5dB -10dB -10.5dB -11dB -11.5dB -12dB -12.5dB -13dB -13.5dB -14dB -14.5dB -15dB -15.5dB -16dB -16.5dB -17dB -17.5dB -18dB -18.5dB -19dB -19.5dB -20dB -20.5dB Operation
No. 7027-7/28
LC75410E, 75410W Volume Control (-21 to -40.5dB)
D8 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 D9 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 D10 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 D11 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 D12 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D13 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D14 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D15 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Operation -21dB -21.5dB -22dB -22.5dB -23dB -23.5dB -24dB -24.5dB -25dB -25.5dB -26dB -26.5dB -27dB -27.5dB -28dB -28.5dB -29dB -29.5dB -30dB -30.5dB -31dB -31.5dB -32dB -32.5dB -33dB -33.5dB -34dB -34.5dB -35dB -35.5dB -36dB -36.5dB -37dB -37.5dB -38dB -38.5dB -39dB -39.5dB -40dB -40.5dB
No. 7027-8/28
LC75410E, 75410W Volume Control (-41 to -59.5dB)
D8 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 D9 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 D10 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 D11 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 D12 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D13 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D14 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D15 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Operation -41dB -41.5dB -42dB -42.5dB -43dB -43.5dB -44dB -44.5dB -45dB -45.5dB -46dB -46.5dB -47dB -47.5dB -48dB -48.5dB -49dB -49.5dB -50dB -50.5dB -51dB -51.5dB -52dB -52.5dB -53dB -53.5dB -54dB -54.5dB -55dB -55.5dB -56dB -56.5dB -57dB -57.5dB -58dB -58.5dB -59dB -59.5dB
No. 7027-9/28
LC75410E, 75410W Volume Control (-60 to -)
D8 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 D9 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 D10 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 D11 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D12 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 D13 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 D14 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D15 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Operation -60dB -60.5dB -61dB -61.5dB -62dB -62.5dB -63dB -63.5dB -64dB -64.5dB -65dB -65.5dB -66dB -66.5dB -67dB -67.5dB -68dB -68.5dB -69dB -69.5dB -70dB -70.5dB -71dB -71.5dB -72dB -72.5dB -73dB -73.5dB -74dB -74.5dB -75dB -75.5dB -76dB -76.5dB -77dB -77.5dB -78dB -78.5dB -79dB -79.5dB -
No. 7027-10/28
LC75410E, 75410W Three-Band Equalizer Control
D16 D20 D24 0 1 0 1 1 0 0 1 1 0 1 1 0 0 1 1 0 1 0 D17 D21 D25 1 0 0 1 1 1 1 0 0 0 0 0 1 1 1 1 0 0 1 D18 D22 D26 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 D19 D23 D27 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 D40 D41 D42 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 0 0 0 +12dB +10dB +8dB +6dB +5dB +4dB +3dB +2dB +1dB 0dB -1dB -2dB -3dB -4dB -5dB -6dB -8dB -10dB -12dB f1 band f2 band f3 band
Fader Volume Control
D28 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 D29 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 D30 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 D31 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0dB -1dB -2dB -4dB -6dB -8dB -10dB -12dB -14dB -16dB -18dB -20dB -30dB -45dB -60dB - Operation
Channel Selection Control
D32 0 1 0 1 D33 0 0 1 1 Operation L/R simultaneously, Initial setting mode RCH LCH L/R simultaneously
No. 7027-11/28
LC75410E, 75410W Fader Rear/Front Control
D34 0 1 Setting Rear Front
Loudness Control
D35 0 1 Setting OFF ON
Zero-Cross Control
D36 0 1 D37 0 1 Setting Data write through zero-cross detection Zero-cross detection stopped (data write at falling edge of CE)
Zero-Cross Signal Detection Block Control
D38 0 1 0 1 D39 0 0 1 1 Selector Volume Tone Fader Setting
Test Mode Control
D43 0 Setting For IC testing. Always set to 0.
No. 7027-12/28
LC75410E, 75410W Pin Functions
Pin Name L1 L2 L3 L4 R1 R2 R3 R4 Pin No. 54 53 52 51 59 60 61 62 * Single-end input pins Function Equivalent circuit
VDD
LVref RVref VDD
L5M L5P R5M R5P
50 49 63 64 * Differential input pins
M VDD P LVref RVref VDD
LSEL0 RSEL0
48 1
* Input selector output pins
VDD
LVRIN RVRIN
47 2
* 2-dB step volume input pins * Perform input at low-impedance.
LVref RVref VDD
LCT RCT 46 3 * Loudness pins. Connect high-pass compensation RC between LCT (RCT) and LVRIN (RVRIN), and connect low-pass compensation RC between LCT (RCT) and GND.
LCOM RCOM
45 4
* 2-dB stop volume output pins. * To reduce switching noise, each of these pins should be connected to Vref through a capacitor.
VDD
VDD
LVROUT RVROUT 44 5 * 0.5-dB step volume output pin
Continued on next page.
No. 7027-13/28
LC75410E, 75410W
Continued from preceding page.
Pin Name Pin No. Function Equivalent circuit
VDD
LTIN RTIN 43 6 * Equalizer input pin LVref RVref LF1C1 LF1C2 LF1C3 RF1C1 RF1C2 RF1C3 42 41 40 7 8 9 * Equalizer F1 band circuit filter configuration capacitor connection pins. Connect capacitor between LF1C1 (RF1C1) and LF1C2 (RF1C2) LF1C2 (RF1C2) and LF1C3 (RF1C3)
VDD VDD TIN
Vref
LF2C1 LF2C2 LF2C3 RF2C1 RF2C2 RF2C3 39 38 37 10 11 12 * Equalizer F2 band circuit filter configuration capacitor connection pins. Connect capacitor between LF2C1 (RF2C1) and LF2C2 (RF2C2) LF2C2 (RF2C2) and LF2C3 (RF2C3)
VDD FnC1 FnC3
VDD
LF3C1 LF3C2 LF3C3 RF3C1 RF3C2 RF3C3
36 35 34 13 14 15 * Equalizer F3 band circuit filter configuration capacitor connection pins. Connect capacitor between LF3C1 (RF3C1) and LF3C2 (RF3C2) LF3C2 (RF3C2) and LF3C3 (RF3C3)
FnC2
VDD
VDD
LTOUT RTOUT 33 16 * Equalizer output pins
VDD
LFIN RFIN 32 17 * Fader block input pins * Drive at low impedance.
VDD
LFOUT LROUT RFOUT RROUT 31 30 18 19 * Fader output pins. Attenuation is possible separately for the front end and rear end. The attenuation amount is the same for L and R.
Vref
57
* Connect a capacitor of a few tens of F between Vref and AVSS (VSS) as a 0.55 VDD voltage generator, current ripple countermeasure.
VDD
LVref RVref
55 58
* Internal analog system ground pins.
LVref RVref Continued on next page. No. 7027-14/28
LC75410E, 75410W
Continued from preceding page.
Pin Name Pin No. Function Equivalent circuit
VDD
56
* Power supply pin
DVSS
27
* Logic system ground pin
LAVSS RAVSS
29 22
* Analog system ground pins
VDD
* External muting control pin MUTE 23 * Setting this pin to VSS level sets forcibly fader volume block to - level.
VDD
* Timer pin when there is no signal in the zero-cross circuit. TIM 20 Forcibly set data when there is no zero-cross signal, from the time the data is set until the timer ends.
CL DI
26 25
* Input pin for serial data and clock used for control
VDD
CE
24
* Chip enable pin. Data is written to the internal latch and the analog switches are operated when the level changes from High to Low. Data transfer is enabled when the level is High.
VDD
TEST 28 * Dedicated IC test pin. * Normally this pin is used connected to GND.
NC
21
* No Connect pin.
No. 7027-15/28
LC75410E, 75410W Internal Equivalent Circuit Block Diagram Selector Block Equivalent Circuit Block Diagram
R3=22.65k L5P R4=25k LVref L5M R1=22.65k L4 50k LVref L3 50k LVref L2 50k LVref L1 50k LVref
+ 0dB
+ 6.702k
LSELO
R2=25k
1.25dB 5.804k 2.50dB 5.026k 3.75dB 4.352k 5.00dB 3.769k 6.25dB 3.264k 7.50dB 2.826k 8.75dB 2.447k 10.0dB 2.119k 11.25dB 1.835k 12.5dB
INMUTE SW
1.589k 13.75dB 1.376k 15.0dB LVref 16.25dB 1.192k 1.032k 17.5dB 0.894k 18.75dB 5.774k LVref
Total resistance: 50 k Same for right channel Unit (Resistance: )
No. 7027-16/28
LC75410E, 75410W 2-dB Volume Block Equivalent Circuit Block Diagram
LVRIN 0dB 41.139k 32.678k 25.957k 20.618k 16.378k 13.009k Total resistance of 195 k over tap 10.334k 8.208k -16dB 6.520k -18dB 5.179k 4.114k -22dB 3.268k 2.596k 2.062k 1.638k 1.301k LCT 6.344k 5.040k 5.750k 4.003k 3.180k 2.526k 2.006k 1.594k 1.266k Total resistance of 30.847 k under tap 1.006k 0.799k -52dB 0.634k 0.504k 0.400k 0.318k -60dB 0.253k 0.201k -64dB 0.159k 0.127k -68dB 0.101k 0.080k -72dB 0.063k 0.050k -76dB 0.040k -78dB 0.154k -dB LVref -74dB -70dB -66dB -62dB -56dB -58dB -54dB -48dB -50dB -40dB -42dB -44dB -46dB -32dB -34dB -36dB -38dB -24dB -26dB -28dB -30dB Same for right channel Unit (Resistance: ) -20dB -2dB -4dB -6dB -8dB -10dB -12dB -14dB To left channel 0.5-dB block
No. 7027-17/28
LC75410E, 75410W 0.5-dB Volume Block Equivalent Circuit Block Diagram
From left channel 2-dB block 2.797k
LVROUT 0dB -0.5dB
Initial setting switch
2.640k -1dB 2.493k -1.5dB 42.070k -dB Vref Initial setting switch
Unit: Total resistance: 50 k Same for right channel
LCOM
No. 7027-18/28
LC75410E, 75410W 3-Band Graphic Equalizer Block Equivalent Circuit Diagram
LTOUT
LTIN 50k LVref
SW2 SW1
SW3 SW1
SW2
SW3 SW1
SW2
SW3
0.027k 12dB 3.373k 10dB 4.246k 8dB 5.346k 6dB 3.172k 5dB 3.558k 4dB 3.993k 3dB 4.480k 2dB 5.027k 1dB 5.640k 0dB
SW4
0.027k 12dB 3.373k 10dB 4.246k 8dB 5.346k 6dB 3.172k 5dB 3.558k 4dB 3.993k 3dB 4.480k 2dB 5.027k 1dB 5.640k 0dB
SW4
0.027k 12dB 3.373k 10dB 4.246k 8dB 5.346k 6dB 3.172k 5dB 3.558k 4dB 3.993k 3dB 4.480k 2dB 5.027k 1dB 5.640k 0dB
SW4
6.50k
6.50k
6.50k
LF1C1
LF1C2
LF1C3
LF2C1
LF2C2
LF2C3
LF3C1
LF3C2
LF3C3
Unit: Total resistance: 38.861 k Same for right channel During boost, SW 1 and SW 3 are ON, during cut SW 2 and SW 4 are ON, and when 0 dB, 0 dB SW and SW 2 and SW 3 are ON.
No. 7027-19/28
LC75410E, 75410W F1/F2/F3 Band Circuit The equivalent circuit and the formula for calculating the external RC with a mean frequency of 1 kHz are shown below. * F1/F2/F3 band equivalent circuit block diagram
R1
R2
C1
C2
R3
* Calculation example Specification Mean frequency: f0 = 1 kHz Gain during maximum boost: G+12 dB = 12 dB Let us use R1 = 0.027 k, R2 = 38.861 k and C1 = C2 = C. 1. Calculate R2 with G+12 dB = 12 dB:
G+12 dB = 20 x LOG10 1 + R3 = R2 10G/20 -1
R2 2R3+R1
- R1 / 2 6.5 k
2. Calculate C with the center frequency f0 = 1 kHz
f0= C=
1 2 (R1+R2)R3C1C2 = 0.010 x 10-6 0.01 F
1 1 = 2f0 (R1+R2)R3 2 x 1000 38888x6500
3. Calculate Q:
Q=
1 (R1+R2)R3
x
R3(R1+R2) 1.22 (2R3+R1)
No. 7027-20/28
LC75410E, 75410W Fader Volume Block Equivalent Circuit Block Diagram
S1 LFIN 0dB 5.437k -1dB 4.846k -2dB 8.169k -4dB 6.489k -6dB 5.154k -8dB 4.094k -10dB 3.252k -12dB 2.583k -14dB 2.052k -16dB 1.630k -18dB 1.295k -20dB 3.419k -30dB 1.300k -45dB 0.231k -60dB 0.050k -dB Unit: Total resistance: 50 k Same for right channel When FADER = "1", S2 and S3 are ON. When FADER = "0", S1 and S4 are ON. S4 LROUT S3 S2 LFOUT
LVref When - data is sent to the main volume, S1 and S2 become open, and S3 and S4 simultaneously become ON.
No. 7027-21/28
LC75410E, 75410W Usage Cautions (1) Data transmission at power ON * The status of internal analog switches is unstable at power ON. Therefore, perform muting or some other countermeasure until the data has been set. * At power ON, initial setting data must be sent once in order to stabilize the bias of each block in a short time.
(2) Description of zero-cross switching circuit operation The LC75410E and 75410W have a function to switch zero-cross comparator signal detection locations, enabling the selection of the optimum detection location for blocks whose data is to be updated. Basically, the switching noise can be minimized by inputting the signal immediately following the block whose data is to be updated to the zero-cross comparator, so it is necessary to switch the detection location every time.
Selector
Volume
Tone
Fader
Switch Zero-cross comparator
LC75410E, 75410W Zero-Cross Detection Circuit (3) Zero-cross switching control method The zero-cross switching control method consists of setting the zero-cross control bits to the zero-cross detection mode (D36, D37 = 0), and specifying the detection blocks (D38, D39) before transmitting the data. These control bits are latched immediately following data transfer, that is to say beforehand in sync with the falling edge of CE, so when updating data of volumes, etc., it is possible to perform mode setting and zero-cross switching with one data transfer. An example of control when updating the data of the volume block is shown below.
D36 0 D37 0 D38 1 Volume block setting D39 0
Zero-cross detection mode setting
(4) Zero-cross timer setting If the input signal becomes lower than the zero-cross comparator detection sensitivity, or if only low-frequency signals are input, zero-cross detection continues to be impossible, and data is not latched during this time. The zero-cross timer can set a time for forcible latch during such a status when zero-cross detection is not possible. For example, to set 25 ms, using T = 0.69CR and C = 0.033 F, we obtain
R=
25 x 10 -3 0.69 x 0.033 x 10 -6
1.1 M
Normally, a value between 10 ms and 50 ms is set.
No. 7027-22/28
LC75410E, 75410W (5) Cautions related to serial data transfer 1. To ensure that the high-frequency digital signals transferred to the CL, DI, and CE pins do not spill over to the analog signal block, either guard these signal lines with a ground pattern, or perform transmission using shielded wires. 2. The data format of the LC75410E and 75410W uses 8-bit addresses and 44-bit data. When sending data using multiples of 8 (when sending 48 bits), use the method described in Figure 1. Method for Receiving Data Using Multiple of 8 of LC75410E and 75410W
X
X
X
X
D0
D1
D2
D3
D36
D37
D38
D39
D40
D41
D42
D43
Dummy data
Input switching control
Test mode control X : don't care
Figure 1
No. 7027-23/28
LC75410E, 75410W
20 18 16
Input Gain Step Characteristics
LC75410E VDD=9V VIN=-30dBV Input L1 Output LFOUT f=1kHz
20 18 16
Input Gain Step Characteristics
LC75410W VDD=9V VIN=-30dBV Input L1 Output LFOUT f=1kHz
Output level -- dB
Output level -- dB
14 12 10 8 6 4 2 0 0
14 12 10 8 6 4 2 0
2
4
6
8
10
12
14
16
18
20
0
2
4
6
8
10
12
14
16
18
20
Step setting -- dB
ILC05428
Step setting -- dB
ILC05429
Graphic equalizer block
Graphic equalizer block
Main volume block
Main volume block
Input gain block
Input gain block
Fader block
V
Fader block
V
0 --10 --20
Main Volume Control Step Characteristics
LC75410E VDD=9V VIN=0dBV Input L1 Output LFOUT f=1kHz
0 --10 --20
Main Volume Control Step Characteristics
LC75410W VDD=9V VIN=0dBV Input L1 Output LFOUT f=1kHz
Attenuation -- dB
--40 --50 --60 --70 --80 --90
Attenuation -- dB
--50 --40 --30 --20 --10 0
--30
--30 --40 --50 --60 --70 --80 --90
--100 --
--70
--60
--100 --
--70
--60
--50
--40
--30
--20
--10
0
Step setting -- dB
ILC05430
Step setting -- dB
ILC05431
Graphic equalizer block
Graphic equalizer block
Main volume block
Main volume block
Input gain block
Input gain block
Fader block
V
Fader block
V
No. 7027-24/28
LC75410E, 75410W
Fader Volume Control Step Characteristics
0 --10 --20
Fader Volume Control Step Characteristics
0 --10 --20
Attenuation -- dB
Attenuation -- dB
--30 --40 --50 --60 --70 --80 --90
LC75410E VDD=9V, VSS=0 VIN=0dBV Input L1 Output LFOUT f=1kHz
--30 --40 --50 --60 --70 --80 --90
LC75410W VDD=9V, VSS=0 VIN=0dBV Input L1 Output LFOUT f=1kHz
--100 --
--70
--60
--50
--40
--30
--20
--10
0
--100 --
--70
--60
--50
--40
--30
--20
--10
0
Step setting -- dB
ILC05432
Step setting -- dB
ILC05433
Graphic equalizer block
Graphic equalizer block
Main volume block
Main volume block
Input gain block
Input gain block
Fader block
Fader block
V
V
THD -- Frequency Characteristics
Total harmonic distortion, THD -- % Total harmonic distortion, THD -- %
1.0 7 5 3 2 0.1 7 5 3 2 0.01 7 5 3 2 23 5 7 100
THD -- Frequency Characteristics
1.0 7 5 3 2 0.1 7 5 3 2 0.01 7 5 3 2 23 5 7 100 23 5 7 1k 23
LC75410E VDD=9V Input L1 Output LFOUT 80kHz LPF
LC75410W VDD=9V Input L1 Output LFOUT 80kHz LPF
VIN=0dBV
VIN=0dBV VIN= --10dBV
VIN= --10dBV
0.001 10
23
5 7 1k
23
5 7 10k
23
Frequency, f -- Hz
5 7100k ILC05434
0.001 10
5 7 10k
23
Frequency, f -- Hz
5 7100k ILC05435
Graphic equalizer block
Graphic equalizer block
Main volume block
Main volume block
Input gain block
Input gain block
Fader block
THD METER
Fader block
THD METER
No. 7027-25/28
LC75410E, 75410W
Total harmonic distortion, THD -- %
3 2 0.1 7 5 3 2
Total harmonic distortion, THD -- %
1.0 7 5
THD -- Input Level Characteristics
1.0 7 5 3 2 0.1 7 5 3 2 0.01 7 5 3 2
THD -- Input Level Characteristics
f
LC75410E VDD=9V, VSS=0 80kHz LPF Input L1, Output LFOUT With VR=0dB
--35 --30 --25 --20 --15 --10
0 =2
kH
z
0.01 7 5 3 2
0 f=1
kH
z
2 f=
LC75410W VDD=9V, VSS=0 80kHz LPF Input L1, Output LFOUT With VR=0dB
--35 --30 --25 --20 --15 --10 --5
0k
Hz
0k Hz
Hz
f=
1k
Hz
f=1
f=1k
0
0.001 --40
--5
0
5
10
0.001 --40
5
10
Input level, VIN -- dB
ILC05436
Input level, VIN -- dB
ILC05437
Graphic equalizer block
Graphic equalizer block
Main volume block
Main volume block
Input gain block
Input gain block
Fader block
Fader block
THD METER
THD METER
THD -- Supply Voltage Characteristics
Total harmonic distortion, THD -- % Total harmonic distortion, THD -- %
1.0 7 5 3 2 0.1 7 5 3 2 0.01 7 5 3 2 4 5 6 7 8 9 10 11 12 13
THD -- Supply Voltage Characteristics
1.0 7 5 3 2 0.1 7 5 3 2 0.01 7 5 3 2 4 5 6
LC75410E VSS=0, VIN=0dBV Input L1 Output LFOUT 80kHz LPF
f=2 0k
LC75410W VSS=0, VIN=0dBV Input L1 Output LFOUT 80kHz LPF
f=1
0k
Hz
f=
Hz
f=
10
kH kH z z
20
f=1
kH
z
f=1
kH
z
0.001
0.001 7 8 9 10 11 12 13
Supply voltage -- V
ILC05438
Supply voltage -- V
ILC05439
Graphic equalizer block
Graphic equalizer block
Main volume block
Main volume block
Input gain block
Input gain block
Fader block
THD METER
Fader block
THD METER
No. 7027-26/28
LC75410E, 75410W
F1 Band Characteristics
0 --5 --10
F1 Band Characteristics
0 --5 --10
LC75410E VDD=9V VIN=-20dBV Input L1 Output LFOUT Level -- dB
LC75410W VDD=9V VIN=-20dBV Input L1 Output LFOUT
Level -- dB
--15 --20 --25 --30 --35 --40 10
--15 --20 --25 --30 --35 --40 10
23
5 7 100
23
5 7 1k
23
5 7 10k
23
Frequency, f -- Hz
5 7100k ILC05440
23
5 7 100
23
5 7 1k
23
5 7 10k
23
Frequency, f -- Hz
0 --5 --10
5 7100k ILC05441
F2 Band Characteristics
0 --5 --10
F2 Band Characteristics
LC75410W VDD=9V VIN=-20dBV Input L1 Output LFOUT
LC75410E VDD=9V VIN=-20dBV Input L1 Output LFOUT Level -- dB
Level -- dB
--15 --20 --25 --30 --35 --40 10
--15 --20 --25 --30 --35 --40 10
23
5 7 100
23
5 7 1k
23
5 7 10k
23
Frequency, f -- Hz
0 --5 --10 --15 --20 --25 --30 --35 --40 10
5 7100k ILC05442
23
5 7 100
23
5 7 1k
23
5 7 10k
23
Frequency, f -- Hz
0 --5 --10
5 7100k ILC05443
F3 Band Characteristics
LC75410E VDD=9V VIN=-20dBV Input L1 Output LFOUT Level -- dB
F3 Band Characteristics
LC75410W VDD=9V VIN=-20dBV Input L1 Output LFOUT
Level -- dB
--15 --20 --25 --30 --35 --40 10
23
5 7 100
23
5 7 1k
23
5 7 10k
23
Frequency, f -- Hz
10
5 7100k ILC05444
23
5 7 100
23
5 7 1k
23
5 7 10k
23
Frequency, f -- Hz
10
5 7100k ILC05445
Output Level Characteristics
VDD = 9 V, VIN = 0, Input: L1, Output: LFOUT For settings from 0 to -54 dB (in 2 dB steps)
0 --2 --4 --6 --8 --10 --12 --14 --16 --18 --20 --22 --24 --26 --28 --30 --32 --34 --36 --38 --40 --42 --44 --46 --48 --50 --52 --54
Output Level Characteristics
VDD = 9 V, VIN = 0, Input: L1, Output: LFOUT For settings from 0 to -54 dB (in 2 dB steps)
0 --2 --4 --6 --8 --10 --12 --14 --16 --18 --20 --22 --24 --26 --28 --30 --32 --34 --36 --38 --40 --42 --44 --46 --48 --50 --52 --54
0
0
--10
--10
Level -- dB
--20
Level -- dB
--20
--30
--30
--40
--40
--50 --60 10
--50 --60 10
LC75410E
23 5 7 100 23 5 7 1k 23 5 7 10k 23
LC75410W
23 5 7 100 23 5 7 1k 23 5 7 10k 23
Frequency, f -- Hz
5 7100k ILC05446
Frequency, f -- Hz
5 7100k ILC05447
No. 7027-27/28
LC75410E, 75410W
Loudness Characteristics
10 10 0
Loudness Characteristics
VDD = 9 V, VIN = 0, Input: L1, Output: LFOUT Loudness on, for settings from 0 to -54 dB (in 2 dB steps)
0 --2 --4 --6 --8 --10 --12 --14 --16 --18 --20 --22 --24 --26 --28 --30 --32 --34 --36 --38 --40 --42 --44 --46 --48 --50 --52 --54
VDD = 9 V, VIN = 0, Input: L1, Output: LFOUT Loudness on, for settings from 0 to -54 dB (in 2 dB steps)
--10
--20
--30
--40
--50 --60 10
0 --2 --4 --6 --8 --10 --12 --14 --16 --18 --20 --22 --24 --26 --28 --30 --32 --34 --36 --38 --40 --42 --44 --46 --48 --50 --52 --54
0
--10
Level -- dB
Level -- dB
--20
--30
--40
--50 --60 10
LC75410E
23 5 7 100 23 5 7 1k 23 5 7 10k 23
LC75410W
23 5 7 100 23 5 7 1k 23 5 7 10k 23
Frequency, f -- Hz
5 7100k ILC05448
Frequency, f -- Hz
5 7100k ILC05449
Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of October, 2001. Specifications and information herein are subject to change without notice. PS No. 7027-28/28

▲Up To Search▲

Price & Availability of LC75410W

	To Download LC75410W Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .