View PSRDA05-4_260836.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

05096
PSRDA3.3-4
thru
Only One Name Means ProT ek'TionTM
PSRDA15-4
STEERING DIODE / TVS ARRA COMBO Y
APPLICA TIONS Ethernet - 10/100 Base T Computer I/O Ports - SCSI, FireWire & USB Set-Top Box Protection Video Card IEC COMPA TIBILITY (EN61000-4) 61000-4-2 (ESD): Air - 15kV, Contact - 8kV 61000-4-4 (EFT): 40A - 5/50ns 61000-4-5 (Surge): 24A, 8/20s - Level 2(Line-Gnd) & Level 3(Line-Line) FEA TURES 500 Watts Peak Pulse Power per Line (tp=8/20s) Unidirectional Configuration Available in 4 Voltage Types: 3.3V to 15V Protects Up to Four (4) I/O Ports ESD Protection > 40 kilovolts LOW CAPACITANCE: 15pF RoHS Compliant in Lead-Free Versions MECHANICAL CHARACTERISTICS Molded JEDEC SO-8 Package Weight 70 milligrams (Approximate) Available in Tin-Lead or Lead-Free Pure-Tin Plating(Annealed) Solder Reflow Temperature: Tin-Lead - Sn/Pb, 85/15: 240-245C Pure-Tin - Sn, 100: 260-270C Flammability Rating UL 94V-0 12mm Tape and Reel Per EIA Standard 481 Marking: Logo, Marking Code, Date Code & Pin One Defined By Dot on Top of Package
SO-8
PIN CONFIGURA TION
GND
I/O 4
I/O 3
GND
8
7
6
5
1
I/O 1
2
+VREF
3
+VREF
4
I/O 2
05096.R7 4/05
1
www.protekdevices.com
PSRDA3.3-4
thru
PSRDA15-4
DEVICE CHARACTERISTICS MAXIMUN RATINGS @ 25C Unless Otherwise Specified
PARAMETER Peak Pulse Power (tp = 8/20s) - See Figure 1 Operating Temperature Storage Temperature Maximum Forward Voltage @ 100mA (See Note 1)
Note 1: Measured between pins 8 or 5 to 1, 2, 3, 4, 6 and 7.
SYMBOL PPP TJ TSTG VF
VALUE 500 -55C to 150C -55C to 150C 1.1
UNITS Watts C C Volts
ELECTRICAL CHARACTERISTICS PER LINE @ 25C Unless Otherwise Specified
PART NUMBER DEVICE MARKING RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE MAXIMUM CLAMPING VOLTAGE (See Fig. 2) @ IP = 1A VC VOLTS 6.5 9.8 19.0 24.0 MAXIMUM CLAMPING VOLTAGE (See Fig. 2) MAXIMUM LEAKAGE CURRENT MAXIMUM CAPACITANCE (See Note 1) (See Figure 5) @0V, 1 MHz Cj(SD) pF 15 15 15 15
VWM VOLTS PSRDA3.3-4 PSRDA05-4 PSRDA12-4 PSRDA15-4 PRA PRB PRD PRE 3.3 5.0 12.0 15.0
@ 1mA V(BR) VOLTS 4.0 6.0 13.3 16.7
@8/20s VC @ IPP 10.9V @ 43.0A 13.5V @ 42.0A 25.9V @ 21.0A 30.0V @ 17.0A
@VWM ID A 125 20 1 1
Note 1: Capacitance measured at VWM = VCC connected between I/O pins to pin 8 and 5 (Gnd). VR = VWM @ 1MHz. As shown in Figure 5, REF1 is connected to ground, REF2 is connected to +VCC, and input applies to VCC = 5V, Vsign = mV, F = 1 MHz.
10,000
PPP - Peak Pulse Power - Watts
FIGURE 1 PEAK PULSE POWER VS PULSE TIME
IPP - Peak Pulse Current - % of IPP
120 100 80 60 40 20 0 tf
FIGURE 2 PULSE WAVE FORM
Peak Value IPP TEST WAVEFORM PARAMETERS tf = 8s td = 20s
1,000
500W 8/20s Waveform
e-t
100
td = t I /2 PP
10 0.1
1
10 100 td - Pulse Duration - s
1,000
10,000
0
5
10
15 t - Time - s
20
25
30
05096.R7 4/05
2
www.protekdevices.com
PSRDA3.3-4
thru
PSRDA15-4
GRAPHS
FIGURE 3 POWER DERATING CURVE
40 Peak Pulse Power 8/20s
5 Volts per Division
100 80
% Of Rated Power
FIGURE 4 OVERSHOOT & CLAMPING VOLTAGE FOR PSRDA05-4
30
60
20
40 20 Average Power 0 0 25 50 75 100 125 TL - Lead Temperature - C 150
10
0 ESD Test Pulse: 8 kilovolt, 1/30ns (waveshape)
FIGURE 5 INPUT CAPACITANCE CIRCUIT
REF2
FIGURE 6 TYPICAL CLAMPING VOLTAGE VS PEAK PULSE CURRENT FOR PSRDA05-4
12
VC - Clamping Voltage - Volts
8
I/O
+VCC
4
VR
G
0 0 REF1 5 10 15 20 IPP - Peak Pulse Current - Amps 25 30
FIGURE 7 INSERTION LOSS - PSRDA12-4
FIGURE 8 RETURN LOSS - PSRDA12-4
20 db
10 db per Division 10 db per Division
20 db
Ref 0 db
Ref 0 db
-20 db
-20 db
-50 db 100 MHz per Division 05096.R7 4/05 3
-50 db 100 MHz per Division www.protekdevices.com
PSRDA3.3-4
thru
PSRDA15-4
APPLICA TION NOTE
The PSRDAxx-4 Series are low capacitance, unidirectional TVS arrays that are designed to protect I/O or high speed data lines from the damaging effects of ESD or EFT. This product series has a surge capability of 500 Watts PPP per line for an 8/20s waveshape and offers ESD protection > 40kV. DIFFERENTIAL-MODE CONFIGURATION (Figure 1) Ideal for use in USB applications, the PSRDAxx-4 Series provides up to four (4) lines of protection in a differential-mode configuration as depicted in Figure 1. Circuit connectivity is as follows: Pins 1, 4, 6 and 7 are connected to the data lines. Pins 5 and 8 are connected to ground. Pins 2 and 3 are connected to the databus. DIFFERENTIAL-MODE CONFIGURATION (Figure 2) The PSRDAxx-4 Series also provides up to four (4) lines of protection in a differential-mode configuration as depicted in Figure 2 for T1/E1 applications. Circuit connectivity is as follows: Pins 1, 4, 6 and 7 are connected to the data lines. Pins 5 and 8 are connected to ground. Pins 2 and 3 are connected to the databus. CIRCUIT BOARD LAYOUT RECOMMENDATIONS Circuit board layout is critical for Electromagnetic Compatibility (EMC) protection. The following guidelines are recommended: The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. The path length between the TVS device and the protected line should be minimized. All conductive loops including power and ground loops should be minimized. The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. Ground planes should be used whenever possible. For multilayer PCBs, use ground vias.
Figure 2. Typical Differential-Mode T1/E1 Protection PTC RTIP PLC016 RRING PTC
T1/E1 TRANSCEIVER
4 3 2 1
Figure 1. Typical Differential-Mode USB Protection USB PORT D+ DVBUS
4 3 2 1
VBUS
GND
USB CONTROLLER
5
6
7
8
USB PORT GND GND D+ DGND
VBUS

5
6
7
8
GND TTIP
GND
PTC
PLC016 TRING PTC
05096.R7 4/05
4
www.protekdevices.com
PSRDA3.3-4
thru
PSRDA15-4
PACKAGE OUTLINE & DIMENSIONS
PACKAGE OUTLINE
-A-
SO-8
8
5 -B - P
+ 0.010 (0.25 MM) M B M 4 PL
DIM A B C D F G J K P R
NOTES 1. 2. 3. 4. 5. 6.
PACKAGE DIMENSIONS MILLIMETERS MIN MAX 4.80 3.80 1.35 0.35 0.40 1.27 BSC 0.18 0.10 5.80 0.25 INCHES MIN MAX
1
4
G
D C R x 45 0 - 10
K 0.010 (0.25 MM) M T B S A S 8 PL
-T-
+
J
F
5.00 0.189 0.196 4.00 0.150 0.157 0.054 0.068 1.75 0.49 0.014 0.019 0.049 1.250 0.016 1.27 BSC 0.05 BSC 0.05 BSC 0.25 0.007 0.009 0.004 0.008 0.25 6.20 0.229 0.244 0.019 0.50 0.010
MOUNTING PAD
0.050 0.005 0.030 0.005
- T - = Seating Plane and Datum Surface. Dimensions "A" and "B" are Datum. Dimensions "A" and "B" do not include mold protrusion. Maximum mold protrusion is 0.015" (0.380 mm) per side. Dimensioning and tolerances per ANSI Y14.5M, 1982. Dimensions are exclusive of mold flash and metal burrs.
TAPE & REEL/BULK ORDERING NOMENCLATURE 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Suffix-T7 = 7 Inch Reel - 1,000 pieces per 12mm tape, i.e., PSRDA05-4-T7. 3. Suffix-LF = Lead-Free, Pure Tin Plating, i.e., PSRDA05-4-LF-T7. 4. Suffix-T13 = 13 Inch Reel - 2,500 pieces per 12mm tape, i.e., PSRDA05-4-T13. 5. No Suffix = Product Shipped in Tubes of 98 pcs per Tube.
0.160 0.005
0.245 MIN
0.045 0.005
Outline & Dimensions: Rev 1 - 11/01, 06009
COPYRIGHT (c) ProTek Devices 2005 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer's and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products.
ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: sales@protekdevices.com Web Site: www.protekdevices.com
05096.R7 4/05
5
www.protekdevices.com

▲Up To Search▲

Price & Availability of PSRDA05-4

	To Download PSRDA05-4 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .