View LPV324_200609.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LPV321 Single/LPV358 Dual/LPV324 Quad General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
July 2003
LPV321 Single/LPV358 Dual/LPV324 Quad General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
General Description
The LPV321/358/324 are low power (9A per channel at 5.0V) versions of the LMV321/358/324 op amps. This is another addition to the LMV321/358/324 family of commodity op amps. The LPV321/358/324 are the most cost effective solutions for the applications where low voltage, low power operation, space saving and low price are needed. The LPV321/358/ 324 have rail-to-rail output swing capability and the input common-mode voltage range includes ground. They all exhibit excellent speed-power ratio, achieving 15 KHz of bandwidth with a supply current of only 9A. The LPV321 is available in space saving SC70-5, which is approximately half the size of SOT23-5. The small package saves space on PC boards, and enables the design of small portable electronic devices. It also allows the designer to place the device closer to the signal source to reduce noise pickup and increase signal integrity. The chips are built with National's advanced submicron silicon-gate BiCMOS process. The LPV321/358/324 have bipolar input and output stages for improved noise performance and higher output current drive.
Features
(For V+ = 5V and V- = 0V, Typical Unless Otherwise Noted)
j Guaranteed 2.7V and 5V Performance j No Crossover Distortion j Space Saving Package j Industrial Temperature Range j Gain-Bandwidth Product j Low Supply Current
SC70-5 2.0x2.1x1.0mm -40C to +85C 152KHz 9A 15A 28A V+-3.5mV V-+90mV -0.2V to V+-0.8V
LPV321 LPV358 LPV324
j Rail-to-Rail Output Swing
@ 100k Load
j VCM
Applications
n Active Filters n General Purpose Low Voltage Applications n General Purpose Portable Devices
Connection Diagrams
5-Pin SC70-5/SOT23-5 8-Pin SO/MSOP 14-Pin SO/TSSOP
10092001
10092002
Top View
Top View
10092003
Top View
(c) 2003 National Semiconductor Corporation
DS100920
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
Absolute Maximum Ratings
(Note 1)
Infrared or Convection (20 sec) Storage Temperature Range Junction Temp. (TJ, max) (Note 5)
235C -65C to 150C 150C
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Machine Model Human Body Model LPV324 LPV358 LPV321 Differential Input Voltage Supply Voltage (V -V ) Output Short Circuit to V Output Short Circuit to V Soldering Information
+ - + -
100V 2000V 1500V 1500V
Operating Ratings (Note 1)
Supply Voltage Temperature Range Thermal Resistance ( 5-pin SC70-5 5-pin SOT23-5 8-Pin SOIC 8-Pin MSOP 14-Pin SOIC 14-Pin TSSOP
JA)(Note 10)
2.7V to 5V -40C to +85C 478C/W 265C/W 190C/W 235C/W 145C/W 155C/W
Supply Voltage
5.5V (Note 3) (Note 4)
2.7V DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T Symbol VOS TCVOS IB IOS CMRR PSRR VCM VO IS Parameter Input Offset Voltage Input Offset Voltage Average Drift Input Bias Current Input Offset Current Common Mode Rejection Ratio Power Supply Rejection Ratio Input Common-Mode Voltage Range Output Swing Supply Current 0V VCM 1.7V 2.7V V+ 5V VO = 1V, VCM = 1V For CMRR 50dB RL = 100k to 1.35V LPV321 LPV358 Both Amplifiers LPV324 All Four Amplifiers
+ J
= 25C, V+ = 2.7V, V- = 0V, VCM = 1.0V, VO = V+/2 and R Conditions Min (Note 7) Typ (Note 6) 1.2 2 1.7 0.6 50 50 0 V -100 70 65 -0.2 1.9 V -3 80 4 8 16 180 8 16 24
+
L
> 1M.
Units mV V/C
Max (Note 7) 7
50 40
nA nA dB dB V
1.7
V mV mV A A A
2.7V AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T Symbol GBWP m Gm en in Parameter Gain-Bandwidth Product Phase Margin Gain Margin Input-Referred Voltage Noise Input-Referred Current Noise f = 1 kHz f = 1 kHz
J
= 25C, V+ = 2.7V, V- = 0V, VCM = 1.0V, VO = V+/2 and R Conditions Min (Note 7) Typ (Note 6) 112 97 35 178 0.50
L
> 1M.
Units KHz Deg dB
Max (Note 7)
CL = 22 pF
www.national.com
2
LPV321 Single/LPV358 Dual/LPV324 Quad
5V DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T Boldface limits apply at the temperature extremes. Symbol VOS TCVOS IB IOS CMRR PSRR VCM AV VO Parameter Input Offset Voltage Input Offset Voltage Average Drift Input Bias Current Input Offset Current Common Mode Rejection Ratio Power Supply Rejection Ratio Input Common-Mode Voltage Range Large Signal Voltage Gain (Note 8) Output Swing 0V VCM 4V 2.7V V+ 5V VO = 1V, VCM = 1V For CMRR 50dB RL = 100k RL = 100k to 2.5V 50 50 0 15 10 V+ -100 V+ -200
J
= 25C, V+ = 5V, V- = 0V, VCM = 2.0V, VO = V+/2 and R Min (Note 7) Typ (Note 6) 1.5 2 2 0.6 71 65 -0.2 4.2 100 V+ -3.5 90 180 220 4 50 60 40 50
L
> 1M.
Conditions
Max (Note 7) 7 10
Units mV V/C nA nA dB dB V V V/mV mV mV
IO
Output Short Circuit Current Sourcing Output Short Circuit Current Sinking
LPV324, LPV358, and LPV321 VO = 0V LPV321 VO = 5V LPV324 and LPV358 VO = 5V
2 20 11
16 60 16 9 15 28 12 15 20 24 42 46
mA mA mA A A A
IS
Supply Current
LPV321 LPV358 Both amplifiers LPV324 All four amplifiers
5V AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T Boldface limits apply at the temperature extremes. Symbol SR GBWP m Gm en in Slew Rate Gain-Bandwidth Product Phase Margin Gain Margin Input-Referred Voltage Noise Input-Referred Current Noise f = 1 kHz, f = 1 kHz Parameter (Note 9) CL = 22 pF
J
= 25C, V+ = 5V, V- = 0V, VCM = 2.0V, VO = V+/2 and R Conditions Min (Note 7) Typ (Note 6) 0.1 152 87 19 146 0.30
L
> 1M.
Units V/s KHz Deg dB
Min (Note 7)
3
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
5V AC Electrical Characteristics
Note 3: Shorting output to V+ will adversely affect reliability. Note 4: Shorting output to V- will adversely affect reliability.
(Continued)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Human body model, 1.5k in series with 100pF. Machine model, 0 in series with 200pF.
Note 5: The maximum power dissipation is a function of TJ(MAX), JA, and TA. The maximum allowable power dissipation at any ambient temperature is P D = (TJ(MAX)-TA)/JA. All numbers apply for packages soldered directly into a PC board. Note 6: Typical values represent the most likely parametric norm. Note 7: All limits are guaranteed by testing or statistical analysis. Note 8: RL is connected to V -. The output voltage is 0.5V VO 4.5V. Note 9: Connected as voltage follower with 3V step input. Number specified is the slower of the positive and negative slew rates. Note 10: All numbers are typical, and apply for packages soldered directly onto a PC board in still air.
Ordering Information
Temperature Range Package 5-Pin SC70-5 5-Pin SOT23-5 8-Pin Small Outline 8-Pin MSOP 14-Pin Small Outline 14-Pin TSSOP Industrial -40C to +85C LPV321M7 LPV321M7X LPV321M5 LPV321M5X LPV358M LPV358MX LPV358MM LPV358MMX LPV324M LPV324MX LPV324MT LPV324MTX A19 A19 A27A A27A LPV358M LPV358M P358 P358 LPV324M LPV324M LPV324MT LPV324MT 1k Units Tape and Reel 3k Units Tape and Reel 1k Units Tape and Reel 3k Units Tape and Reel Rails 2.5k Units Tape and Reel 1k Units Tape and Reel 3.5k Units Tape and Reel Rails 2.5k Units Tape and Reel Rails 2.5k Units Tape and Reel M08A MUA08A M14A MTC14 MA05B MAA05 Packaging Marking Transport Media NSC Drawing
www.national.com
4
LPV321 Single/LPV358 Dual/LPV324 Quad
Typical Performance Characteristics
TA = 25C. Supply Current vs. Supply Voltage (LPV321)
Unless otherwise specified, VS = +5V, single supply, Input Current vs. Temperature
100920B4
100920B5
Sourcing Current vs. Output Voltage
Sourcing Current vs. Output Voltage
10092041
10092042
Sinking Current vs. Output Voltage
Sinking Current vs. Output Voltage
10092043
10092044
5
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
Typical Performance Characteristics Unless otherwise specified, VS = +5V, single supply,
TA = 25C. (Continued) Input Voltage Noise vs. Frequency
Output Voltage Swing vs. Supply Voltage
100920B6
10092056
Input Current Noise vs Frequency
Input Current Noise vs Frequency
10092070
10092068
Crosstalk Rejection vs. Frequency
PSRR vs. Frequency
10092073
10092072
www.national.com
6
LPV321 Single/LPV358 Dual/LPV324 Quad
Typical Performance Characteristics Unless otherwise specified, VS = +5V, single supply,
TA = 25C. (Continued) CMRR vs. Frequency CMRR vs. Input Common Mode Voltage
10092063
10092064
CMRR vs. Input Common Mode Voltage
VOS vs. VCM
10092065
10092045
VOS vs. VCM
Input Voltage vs. Output Voltage
10092046
10092069
7
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
Typical Performance Characteristics Unless otherwise specified, VS = +5V, single supply,
TA = 25C. (Continued) Input Voltage vs. Output Voltage Open Loop Frequency Response
10092071
10092052
Open Loop Frequency Response
Gain and Phase vs. Capacitive Load
10092051
10092054
Gain and Phase vs. Capacitive Load
Slew Rate vs. Supply Voltage
10092053
10092055
www.national.com
8
LPV321 Single/LPV358 Dual/LPV324 Quad
Typical Performance Characteristics Unless otherwise specified, VS = +5V, single supply,
TA = 25C. (Continued) Non-Inverting Large Signal Pulse Response Non-Inverting Small Signal Pulse Response
10092050
10092049
Inverting Large Signal Pulse Response
Inverting Small Signal Pulse Response
10092047
10092048
Stability vs. Capacitive Load
Stability vs. Capacitive Load
10092061
10092060
9
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
Typical Performance Characteristics Unless otherwise specified, VS = +5V, single supply,
TA = 25C. (Continued) Stability vs. Capacitive Load Stability vs. Capacitive Load
10092059
10092058
THD vs. Frequency
Open Loop Output Impedance vs Frequency
10092074 10092062
Short Circuit Current vs. Temperature (Sinking)
Short Circuit Current vs. Temperature (Sourcing)
100920B7
100920B8
www.national.com
10
LPV321 Single/LPV358 Dual/LPV324 Quad
Application Information
1.0 BENEFITS OF THE LPV321/358/324 Size The small footprints of the LPV321/358/324 packages save space on printed circuit boards, and enable the design of smaller electronic products, such as cellular phones, pagers, or other portable systems. The low profile of the LPV321/ 358/324 make them possible to use in PCMCIA type III cards. Signal Integrity Signals can pick up noise between the signal source and the amplifier. By using a physically smaller amplifier package, the LPV321/358/324 can be placed closer to the signal source, reducing noise pickup and increasing signal integrity. Simplified Board Layout These products help you to avoid using long pc traces in your pc board layout. This means that no additional components, such as capacitors and resistors, are needed to filter out the unwanted signals due to the interference between the long pc traces. Low Supply Current These devices will help you to maximize battery life. They are ideal for battery powered systems. Low Supply Voltage National provides guaranteed performance at 2.7V and 5V. These guarantees ensure operation throughout the battery lifetime. Rail-to-Rail Output Rail-to-rail output swing provides maximum possible dynamic range at the output. This is particularly important when operating on low supply voltages. Input Includes Ground Allows direct sensing near GND in single supply operation. The differential input voltage may be larger than V + without damaging the device. Protection should be provided to prevent the input voltages from going negative more than -0.3V (at 25C). An input clamp diode with a resistor to the IC input terminal can be used. 2.0 CAPACITIVE LOAD TOLERANCE The LPV321/358/324 can directly drive 200pF in unity-gain without oscillation. The unity-gain follower is the most sensitive configuration to capacitive loading. Direct capacitive loading reduces the phase margin of amplifiers. The combination of the amplifier's output impedance and the capacitive load induces phase lag. This results in either an underdamped pulse response or oscillation. To drive a heavier capacitive load, circuit in Figure 1 can be used.
10092075
10092004
FIGURE 1. Indirectly Driving A Capacitive Load Using Resistive Isolation In Figure 1, the isolation resistor RISO and the load capacitor CL form a pole to increase stability by adding more phase margin to the overall system. The desired performance depends on the value of RISO. The bigger the RISO resistor value, the more stable VOUT will be. Figure 2 is an output waveform of Figure 1 using 100k for RISO and 1000pF for C L.
FIGURE 2. Pulse Response of the LPV324 Circuit in Figure 1 The circuit in Figure 3 is an improvement to the one in Figure 1 because it provides DC accuracy as well as AC stability. If there were a load resistor in Figure 1, the output would be voltage divided by RISO and the load resistor. Instead, in Figure 3, RF provides the DC accuracy by using feedforward techniques to connect VIN to RL. Caution is needed in choosing the value of R F due to the input bias current of the LPV321/358/324. C F and RISO serve to counteract the loss of phase margin by feeding the high frequency component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the overall feedback loop. Increased capacitive drive is possible by increasing the value of CF. This in turn will slow down the pulse response.
11
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
Application Information
(Continued)
10092007 10092005
FIGURE 3. Indirectly Driving A Capacitive Load with DC Accuracy 3.0 INPUT BIAS CURRENT CANCELLATION The LPV321/358/324 family has a bipolar input stage. The typical input bias current of LPV321/358/324 is 1.5nA with 5V supply. Thus a 100k input resistor will cause 0.15mV of error voltage. By balancing the resistor values at both inverting and non-inverting inputs, the error caused by the amplifier's input bias current will be reduced. The circuit in Figure 4 shows how to cancel the error caused by input bias current.
FIGURE 5. Difference Amplifier 4.2 Instrumentation Circuits The input impedance of the previous difference amplifier is set by the resistor R1, R2, R3, and R 4. To eliminate the problems of low input impedance, one way is to use a voltage follower ahead of each input as shown in the following two instrumentation amplifiers. 4.2.1 Three-op-amp Instrumentation Amplifier The quad LPV324 can be used to build a three-op-amp instrumentation amplifier as shown in Figure 6
10092006
FIGURE 4. Cancelling the Error Caused by Input Bias Current 4.0 TYPICAL SINGLE-SUPPLY APPLICATION CIRCUITS 4.1 Difference Amplifier The difference amplifier allows the subtraction of two voltages or, as a special case, the cancellation of a signal common to two inputs. It is useful as a computational amplifier, in making a differential to single-ended conversion or in rejecting a common mode signal.
10092085
FIGURE 6. Three-op-amp Instrumentation Amplifier The first stage of this instrumentation amplifier is a differential-input, differential-output amplifier, with two voltage followers. These two voltage followers assure that the input impedance is over 100M. The gain of this instrumentation amplifier is set by the ratio of R2/R 1. R3 should equal R1 and R4 equal R2. Matching of R3 to R1 and R4 to R2 affects the CMRR. For good CMRR over temperature, low drift resistors should be used. Making R4 Slightly smaller than R 2 and adding a trim pot equal to twice the difference between R 2 and R4 will allow the CMRR to be adjusted for optimum.
www.national.com
12
LPV321 Single/LPV358 Dual/LPV324 Quad
Application Information
(Continued)
5.0 ACTIVE FILTER Simple Low-Pass Active Filter The simple low-pass filter is shown in Figure 9. Its lowfrequency gain( o) is defined by -R3/R1. This allows low-frequency gains other than unity to be obtained. The filter has a -20dB/decade roll-off after its corner frequency fc. R2 should be chosen equal to the parallel combination of R1 and R3 to minimize errors due to bais current. The frequency response of the filter is shown in Figure 10
4.2.2 Two-op-amp Instrumentation Amplifier A two-op-amp instrumentation amplifier can also be used to make a high-input-impedance DC differential amplifier (Figure 7). As in the three-op-amp circuit, this instrumentation amplifier requires precise resistor matching for good CMRR. R4 should equal to R1 and R3 should equal R2.
10092011
10092014
FIGURE 7. Two-op-amp Instrumentation Amplifier 4.3 Single-Supply Inverting Amplifier There may be cases where the input signal going into the amplifier is negative. Because the amplifier is operating in single supply voltage, a voltage divider using R3 and R4 is implemented to bias the amplifier so the input signal is within the input common-common voltage range of the amplifier. The capacitor C1 is placed between the inverting input and resistor R1 to block the DC signal going into the AC signal source, VIN. The values of R1 and C1 affect the cutoff frequency, fc = 1/2 R 1C1. As a result, the output signal is centered around mid-supply (if the voltage divider provides V+/2 at the non-inverting input). The output can swing to both rails, maximizing the signal-to-noise ratio in a low voltage system.
FIGURE 9. Simple Low-Pass Active Filter
10092015
FIGURE 10. Frequency Response of Simple Low-pass Active Filter in Figure 9 Note that the single-op-amp active filters are used in to the applications that require low quality factor, Q ( 10), low frequency ( 5KHz), and low gain ( 10), or a small value for the product of gain times Q ( 100). The op amp should have an open loop voltage gain at the highest frequency of interest at least 50 times larger than the gain of the filter at this frequency. In addition, the selected op amp should have a slew rate that meets the following requirement: Slew Rate 0.5 x (HV OPP) X 10-6V/sec Where H is the highest frequency of interest, and VOPP is the output peak-to-peak voltage.
10092013
FIGURE 8. Single-Supply Inverting Amplifier
13
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
SC70-5 Tape and Reel Specification
100920B3
SOT-23-5 Tape and Reel Specification
TAPE FORMAT Tape Section Leader (Start End) Carrier Trailer (Hub End)
# Cavities
0 (min) 75 (min) 3000 250 125 (min) 0 (min)
Cavity Status Empty Empty Filled Filled Empty Empty
Cover Tape Status Sealed Sealed Sealed Sealed Sealed Sealed
www.national.com
14
LPV321 Single/LPV358 Dual/LPV324 Quad
SOT-23-5 Tape and Reel Specification (Continued)
TAPE DIMENSIONS
100920B1
8 mm Tape Size
0.130 (3.3) DIM A
0.124 (3.15) DIM Ao
0.130 (3.3) DIM B
0.126 (3.2) DIM Bo
0.138 0.002 (3.5 0.05) DIM F
0.055 0.004 (1.4 0.11) DIM Ko
0.157 (4) DIM P1
0.315 0.012 (8 0.3) DIM W
15
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
SOT-23-5 Tape and Reel Specification (Continued)
REEL DIMENSIONS
100920B2
8 mm Tape Size
7.00 330.00 A
0.059 0.512 0.795 2.165 1.50 B 13.00 20.20 55.00 C D N
0.331 + 0.059/-0.000 8.40 + 1.50/-0.00 W1
0.567 14.40 W2
W1+ 0.078/-0.039 W1 + 2.00/-1.00 W3
www.national.com
16
LPV321 Single/LPV358 Dual/LPV324 Quad
Physical Dimensions
unless otherwise noted
inches (millimeters)
5-Pin SC70-5 Tape and Reel NS Package Number MAA05A
17
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
5-Pin SOT23-5 Tape and Reel NS Package Number MA05B
www.national.com
18
LPV321 Single/LPV358 Dual/LPV324 Quad
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
8-Pin Small Outline NS Package Number M08A
8-Pin MSOP NS Package Number MUA08A
19
www.national.com
LPV321 Single/LPV358 Dual/LPV324 Quad
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
14-Pin Small Outline NS Package Number M14A
14-Pin TSSOP NS Package Number MTC14
www.national.com
20
LPV321 Single/LPV358 Dual/LPV324 Quad General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Notes
LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com
National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.

▲Up To Search▲

Price & Availability of LPV324

	To Download LPV324 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .