View MC34156FN_135484.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Order this document from Analog Marketing
Product Preview
MC34156
28-Channel Inkjet Driver
The MC34156 is a 28-Channel Decoder/Driver intended to be used in inkjet printer applications. By using sophisticated SMARTMOSTM technology, it has been possible to combine low power CMOS inputs and logic and high current, high voltage bipolar outputs capable of sustaining a maximum of 30 V. A 4-to-14 line decoder determines the selected output driver (n) in each 14-driver bank. Two independent output enable inputs (active low) then provide the final decoding to activate 1- or 2-of-28 outputs (OUTAn and/or OUTBn). The ac electrical characteristics of the drivers are tightly controlled and thereby the energy of the device delivers to the inkjet print head. A Chip Enable function is provided to lock out the drivers during system power up. The 28 bipolar power outputs are open collector 30 V Darlington drivers capable of sinking 500 mA at ambient temperatures up to 70C. All driver outputs are capable of withstanding a contact discharge of 8.0 kV with the IC biased. * ESD Output Protection with Clamping Diodes
28-CHANNEL INKJET DRIVER
(SMARTMOSTM Technology)
SEMICONDUCTOR TECHNICAL DATA
* * * *
Addressable Data Entry Tightly Controlled AC and Electrical Characteristics for Inkjet Printers CMOS, TTL Compatible Inputs Low Power CMOS Logic
44 1
FN SUFFIX PLASTIC PACKAGE CASE 777
SMARTMOS is a trademark of Motorola, Inc.
ORDERING INFORMATION
Device MC34156FN Operating Temperature Range TA = 0 to +70C
PIN ASSIGNMENTS
Package Plastic Package
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Pin Name IND VDD Gnd ENB Chip Enable OUTB0 OUTB1 OUTB2 OUTB3 OUTB4 OUTB5 OUTB6 OUTB7 OUTB8 OUTB9 Gnd N/C N/C N/C OUTB10 OUTB11 OUTB12 OUTB13 OUTA13 OUTA12 OUTA11 OUTA10 COM Gnd OUTA9 OUTA8 OUTA7 OUTA6 OUTA5 OUTA4 OUTA3 OUTA2 OUTA1 OUTA0 ENA INA Gnd INB INC Pin Description 4th Decoder Input Power Supply Ground Enable Pin for B Set Drivers Chip Enable B Set 1st Driver B Set 2nd Driver B Set 3rd Driver B Set 4th Driver B Set 5th Driver B Set 6th Driver B Set 7th Driver B Set 8th Driver B Set 9th Driver B Set 10th Driver Ground Not Connected Not Connected Not Connected B Set 11th Driver B Set 12th Driver B Set 13th Driver B Set 14th Driver A Set 14th Driver A Set 13th Driver A Set 12th Driver A Set 11th Driver Common Ground A Set 10th Driver A Set 9th Driver A Set 8th Driver A Set 7th Driver A Set 6th Driver A Set 5th Driver A Set 4th Driver A Set 3rd Driver A Set 2nd Driver A Set 1st Driver Enable Pin for A Set Drivers 1st Decoder Input Ground 2nd Decoder Input 3rd Decoder Input
Simplified Block Diagram
Output Enable B V DD 2 Logic Supply
40 Output Enable A
Chip Enable
IND (MSB)
OUTB1 OUTB2 OUTB3
41 INA (LSB)
OUTB0
Gnd
42 Gnd
44 INC
43 INB
6
5
4
3
1
7 8 9
39 38 37
OUTA0 OUTA1 OUTA2 OUTA3 OUTA4 OUTA5 OUTA6 OUTA7 OUTA8 OUTA9 Gnd
4-To-14 Line Decoder
Output Driver Bank B
OUTB5 11 OUTB6 12 OUTB7
13
Output Driver Bank A
OUTB4 10
36 35 34 33 32 31 30 29
OUTB8 14 OUTB9 15 Gnd N/C
16 17
N/C 18
N/C 19
OUTB10 20
OUTB11 21
OUTB12 22
OUTB13 23
OUTA13 24
OUTA12 25
OUTA11 26
OUTA10 27
COM 28
This document contains information on a product under development. Motorola reserves the right to change or discontinue thisIC DEVICE DATA MOTOROLA ANALOG product without notice.
(c) Motorola, Inc. 1996
Issue 0
1
MC34156
Figure 1. Functional Block Diagram
Output Enable A Turn Off Delay
OUTA0
OUTA1 Logic Supply OUTA2
Chip Enable
OUTA13
INA (LSB) 4-to-14 Line Decoder OUTB0
INB
OUTB1
INC
OUTB2 IND (MSB)
Output Enable B
Turn On Delay
OUTB13
Figure 2. Output Driver Configuration
COM OUT
Figure 3. Typical Input Circuit
VDD
IN
2
MOTOROLA ANALOG IC DEVICE DATA
MC34156
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PACKAGE CASE 777-02 ISSUE C -N- Y
BRK
D
B
0.007(0.180) M T U
L-M
S
N
S S
0.007(0.180) M T
L-M
N
S
Z -L- -M-
V
44 1
W
D L-M L-M
S S
X VIEW D-D
G1 0.010 (0.25)
S
T
L-M
S
N
S
A R Z
0.007(0.180) M T 0.007(0.180) M T
N N
S
H
S
0.007(0.180) M T
L-M
S
N
S
J C G G1 0.010 (0.25)
S
K1 K F 0.007(0.180) M T VIEW S
DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.685 0.695 0.685 0.695 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.650 0.656 0.650 0.656 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.610 0.630 0.040 --- MILLIMETERS MIN MAX 17.40 17.65 17.40 17.65 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 16.51 16.66 16.51 16.66 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10_ 15.50 16.00 1.02 ---
E 0.004 (0.10) -T- SEATING
PLANE
T
L-M
S
N
S
VIEW S
L-M
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- ARE DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.25) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA ANALOG IC DEVICE DATA
*MC34156/D*
MC34156/D
3

▲Up To Search▲

Price & Availability of MC34156FN

	To Download MC34156FN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .