View MCM6229BBXJ17_44766.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document by MCM6229BB/D
Product Preview
MCM6229BB
XJ PACKAGE 400 MIL SOJ CASE 810-03
256K x 4 Bit Static Random Access Memory
The MCM6229BB is a 1,048,576 bit static random access memory organized as 262,144 words of 4 bits. Static design eliminates the need for external clocks or timing strobes while CMOS circuitry reduces power consumption and provides for greater reliability. The MCM6229BB is equipped with both chip enable (E) and output enable (G) pins, allowing for greater system flexibility and eliminating bus contention problems. The MCM6229BB is available in 300 mil and 400 mil, 28 lead surface-mount SOJ packages. * * * * * * Single 5 V 10% Power Supply Fast Access Times: 15/17/20/25/35 ns Equal Address and Chip Enable Access Times All Inputs and Outputs are TTL Compatible and LVTTL Compatible Three State Outputs Low Power Operation: 155/150/135/130/110 mA Maximum, Active AC BLOCK DIAGRAM
A A A A A A A A A ROW DECODER MEMORY MATRIX 512 ROWS x 2048 COLUMNS
EJ PACKAGE 300 MIL SOJ CASE 810B-03
PIN ASSIGNMENTS
A A A A A A A A A A A E G VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14
28 27 26 25 24 23 22 21 20 19 18 17 16 15
VCC A A A A A A A NC* DQ DQ DQ DQ W
DQ INPUT DATA CONTROL DQ A A A
COLUMN I/O COLUMN DECODER
PIN NAMES
A . . . . . . . . . . . . . . . . . . . . Address Inputs W . . . . . . . . . . . . . . . . . . . . . Write Enable G . . . . . . . . . . . . . . . . . . . Output Enable E . . . . . . . . . . . . . . . . . . . . . . Chip Enable DQ . . . . . . . . . . . . . Data Inputs/Outputs VCC . . . . . . . . . . . . . + 5 V Power Supply VSS . . . . . . . . . . . . . . . . . . . . . . . Ground NC* . . . . . . . . . . . . . . . . . No Connection *If not used for no connect, then do not exceed voltages of - 0.5 to VCC + 0.5 V. This pin is used for manufacturing diagnostics.
A
A
A
A
A
A
E W G
This document contains information on a new product under development. Motorola reserves the right to change or discontinue this product without notice. 11/7/96
(c) Motorola, Inc. 1995 MOTOROLA FAST SRAM
MCM6229BB 1
TRUTH TABLE
E H L L L G X H L X W X H H L Mode Not Selected Output Disabled Read Write I/O Pin High-Z High-Z Dout Din Cycle -- -- Read Write Current ISB1, ISB2 ICCA ICCA ICCA
H = High, L = Low, X = Don't Care
ABSOLUTE MAXIMUM RATINGS (See Note)
Rating Power Supply Voltage Relative to VSS Voltage Relative to VSS for Any Pin Except VCC Output Current (per I/O) Power Dissipation Temperature Under Bias Operating Temperature Symbol VCC Vin, Vout Iout PD Tbias TA Value - 0.5 to 7.0 - 0.5 to VCC + 0.5 20 1.0 - 10 to + 85 0 to + 70 Unit V V mA W C C This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to these high-impedance circuits. This CMOS memory circuit has been designed to meet the dc and ac specifications shown in the tables, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow of at least 500 linear feet per minute is maintained.
Storage Temperature Tstg - 55 to + 150 C NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to RECOMMENDED OPERATING CONDITIONS. Exposure to higher than recommended voltages for extended periods of time could affect device reliability.
DC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V 10%, TA = 0 to 70C, Unless Otherwise Noted) RECOMMENDED OPERATING CONDITIONS
Parameter Supply Voltage (Operating Voltage Range) Input High Voltage Input Low Voltage * VIL (min) = - 0.5 V dc; VIL (min) = - 2.0 V ac (pulse width 20 ns). ** VIH (max) = VCC + 0.3 V dc; VIH (max) = VCC + 2 V ac (pulse width 20 ns). Symbol VCC VIH VIL Min 4.5 2.2 - 0.5* Max 5.5 VCC + 0.3** 0.8 Unit V V V
DC CHARACTERISTICS AND SUPPLY CURRENTS
Parameter Input Leakage Current (All Inputs, Vin = 0 to VCC) Output Leakage Current (E = VIH, Vout = 0 to VCC) AC Active Supply Current (Iout = 0 mA, all inputs = VIL or VIH, VIL = 0, VIH 3 V, cycle time tAVAV min, VCC = max) MCM6229BB-15: tAVAV = 15 ns MCM6229BB-17: tAVAV = 17 ns MCM6229BB-20: tAVAV = 20 ns MCM6229BB-25: tAVAV = 25 ns MCM6229BB-35: tAVAV = 35 ns MCM6229BB-15: tAVAV = 15 ns MCM6229BB-17: tAVAV = 17 ns MCM6229BB-20: tAVAV = 20 ns MCM6229BB-25: tAVAV = 25 ns MCM6229BB-35: tAVAV = 35 ns Symbol Ilkg(I) Ilkg(O) ICCA Min -- -- -- -- -- -- -- -- -- -- -- -- -- -- 2.4 Max 1 1 155 150 135 130 110 45 40 35 30 25 5 0.4 -- Unit A A mA
AC Standby Current (VCC = max, E = VIH, f = fmax)
ISB1
mA
CMOS Standby Current (E VCC - 0.2 V, Vin VSS + 0.2 V or VCC - 0.2 V, VCC = max, f = 0 MHz) Output Low Voltage (IOL = + 8.0 mA) Output High Voltage (IOH = - 4.0 mA)
ISB2 VOL VOH
mA V V
MCM6229BB 2
MOTOROLA FAST SRAM
CAPACITANCE (f = 1.0 MHz, dV = 3.0 V, TA = 25C, Periodically Sampled Rather Than 100% Tested)
Characteristic Input Capacitance I/O Capacitance All Inputs Except Clocks and DQs E, G, and W DQ Symbol Cin Cck CI/O Typ 4 5 5 Max 6 8 8 Unit pF pF
AC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V 10%, TA = 0 to + 70C, Unless Otherwise Noted)
Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ns Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V Output Timing Measurement Reference Level . . . . . . . . . . . . . 1.5 V Output Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Figure 1a
READ CYCLE TIMING (See Notes 1, 2, and 3)
6229BB-15 Parameter Read Cycle Time Address Access Time Enable Access Time Output Enable Access Time Output Hold from Address Change Enable Low to Output Active Output Enable Low to Output Active Enable High to Output High-Z Output Enable High to Output High-Z Symbol tAVAV tAVQV tELQV tGLQV tAXQX tELQX tGLQX tEHQZ tGHQZ Min 15 -- -- -- 3 5 0 0 0 Max -- 15 15 6 -- -- -- 6 6 6229BB-17 Min 17 -- -- -- 3 5 0 0 0 Max -- 17 17 7 -- -- -- 7 7 6229BB-20 Min 20 -- -- -- 3 5 0 0 0 Max -- 20 20 7 -- -- -- 7 7 6229BB-25 Min 25 -- -- -- 3 5 0 0 0 Max -- 25 25 8 -- -- -- 8 8 6229BB-35 Min 35 -- -- -- 3 5 0 0 0 Max -- 35 35 8 -- -- -- 8 8 Unit ns ns ns ns ns ns ns ns ns 5, 6, 7 5, 6, 7 5, 6, 7 5, 6, 7 4 Notes 3
NOTES: 1. W is high for read cycle. 2. Product sensitivities to noise require proper grounding and decoupling of power supplies as well as minimization or elimination of bus contention conditions during read and write cycles. 3. All timings are referenced from the last valid address to the first transitioning address. 4. Addresses valid prior to or coincident with E going low. 5. At any given voltage and temperature, tEHQZ max is less than tELQX min, and tGHQZ max is less than tGLQX min, both for a given device and from device to device. 6. Transition is measured 500 mV from steady-state voltage with load of Figure 1b. 7. This parameter is sampled and not 100% tested. 8. Device is continuously selected (E VIL, G VIL).
+5 V OUTPUT Z0 = 50 RL = 50 VL = 1.5 V OUTPUT 255 5 pF 480
TIMING LIMITS
The table of timing values shows either a minimum or a maximum limit for each parameter. Input requirements are specified from the external system point of view. Thus, address setup time is shown as a minimum since the system must supply at least that much time. On the other hand, responses from the memory are specified from the device point of view. Thus, the access time is shown as a maximum since the device never provides data later than that time.
(a)
(b)
Figure 1. AC Test Loads
MOTOROLA FAST SRAM
MCM6229BB 3
READ CYCLE 1 (See Notes 1, 2, 3, and 9)
tAVAV A (ADDRESS) tAXQX Q (DATA OUT) PREVIOUS DATA VALID tAVQV DATA VALID
READ CYCLE 2 (See Notes 3 and 5)
tAVAV A (ADDRESS) tELQV E (CHIP ENABLE) tELQX G (OUTPUT ENABLE) tGLQV tGLQX Q (DATA OUT) HIGH-Z tAVQV tELICCH ICC SUPPLY CURRENT ISB tEHICCL DATA VALID tGHQZ tEHQZ
MCM6229BB 4
MOTOROLA FAST SRAM
WRITE CYCLE 1 (W Controlled, See Notes 1, 2, 3, and 4)
6229BB-15 Parameter Write Cycle Time Address Setup Time Address Valid to End of Write Write Pulse Width Data Valid to End of Write Data Hold TIme Write Low to Data High-Z Write High to Output Active Write Recovery Time Symbol tAVAV tAVWL tAVWH tWLWH, tWLEH tDVWH tWHDX tWLQZ tWHQX tWHAX Min 15 0 12 12 7 0 -- 5 0 Max -- -- -- -- -- -- 6 -- -- 6229BB-17 Min 17 0 14 14 8 0 -- 5 0 Max -- -- -- -- -- -- 7 -- -- 6229BB-20 Min 20 0 15 15 9 0 -- 5 0 Max -- -- -- -- -- -- 7 -- -- 6229BB-25 Min 25 0 17 17 10 0 -- 5 0 Max -- -- -- -- -- -- 8 -- -- 6229BB-35 Min 35 0 20 20 11 0 -- 5 0 Max -- -- -- -- -- -- 8 -- -- Unit ns ns ns ns ns ns ns ns ns 5, 6, 7 5, 6, 7 Notes 4
NOTES: 1. A write occurs during the overlap of E low and W low. 2. Product sensitivities to noise require proper grounding and decoupling of power supplies as well as minimization or elimination of bus contention conditions during read and write cycles. 3. If G goes low coincident with or after W goes low, the output will remain in a high-impedance state. 4. All timings are referenced from the last valid address to the first transitioning address. 5. Transition is measured 500 mV from steady-state voltage with load of Figure 1b. 6. This parameter is sampled and not 100% tested. 7. At any given voltage and temperature, tWLQZ max is less than tWHQX min both for a given device and from device to device.
WRITE CYCLE 1 (W Controlled See Notes 1, 2, 3, and 4)
tAVAV A (ADDRESS) tAVWH E (CHIP ENABLE) tWLWH tWLEH W (WRITE ENABLE) tAVWL D (DATA IN) tWLQZ Q (DATA OUT) HIGH-Z HIGH-Z tDVWH DATA VALID tWHQX tWHDX tWHAX
MOTOROLA FAST SRAM
MCM6229BB 5
WRITE CYCLE 2 (E Controlled, See Notes 1, 2, and 3)
6229BB-15 Parameter Write Cycle Time Address Setup Time Address Valid to End of Write Enable to End of Write Write Pulse Width Data Valid to End of Write Data Hold Time Write Recovery Time Symbol tAVAV tAVEL tAVEH tELEH, tELWH tWLEH tDVEH tEHDX tEHAX Min 15 0 12 12 12 7 0 0 Max -- -- -- -- -- -- -- -- 6229BB-17 Min 17 0 14 14 14 8 0 0 Max -- -- -- -- -- -- -- -- 6229BB-20 Min 20 0 15 15 15 9 0 0 Max -- -- -- -- -- -- -- -- 6229BB-25 Min 25 0 17 17 17 10 0 0 Max -- -- -- -- -- -- -- -- 6229BB-35 Min 35 0 20 20 20 11 0 0 Max -- -- -- -- -- -- -- -- Unit ns ns ns ns ns ns ns ns 5, 6 Notes 4
NOTES: 1. A write occurs during the overlap of E low and W low. 2. Product sensitivities to noise require proper grounding and decoupling of power supplies as well as minimization or elimination of bus contention conditions during read and write cycles. 3. If G goes low coincident with or after W goes low, the output will remain in a high-impedance state. 4. All timings are referenced from the last valid address to the first transitioning address. 5. If E goes low coincident with or after W goes low, the output will remain in a high-impedance state. 6. If E goes high coincident with or before W goes high, the output will remain in a high-impedance state.
WRITE CYCLE 2 (E Controlled See Notes 1, 2, 3, and 4)
tAVAV A (ADDRESS) tAVEH tELEH E (CHIP ENABLE) tAVEL tWLEH W (WRITE ENABLE) tDVEH D (DATA IN) DATA VALID tEHDX Q (DATA OUT) HIGH-Z tELWH tEHAX
ORDERING INFORMATION
(Order by Full Part Number) MCM 6229BB XX
Motorola Memory Prefix Part Number
XX
XX
Shipping Method (R2 = Tape and Reel, Blank = Rails) Speed (15 = 15 ns, 17 = 17 ns, 20 = 20 ns, 25 = 25 ns, 35 = 35 ns) Package (XJ = 400 mil SOJ, EJ = 300 mil SOJ)
Full Part Numbers -- MCM6229BBXJ15 MCM6229BBXJ17 MCM6229BBXJ20 MCM6229BBXJ25 MCM6229BBXJ35
MCM6229BBXJ15R2 MCM6229BBXJ17R2 MCM6229BBXJ20R2 MCM6229BBXJ25R2 MCM6229BBXJ35R2
MCM6229BBEJ15 MCM6229BBEJ17 MCM6229BBEJ20 MCM6229BBEJ25 MCM6229BBEJ35
MCM6229BBEJ15R2 MCM6229BBEJ17R2 MCM6229BBEJ20R2 MCM6229BBEJ25R2 MCM6229BBEJ35R2
MCM6229BB 6
MOTOROLA FAST SRAM
PACKAGE DIMENSIONS
28 LEAD 400 MIL SOJ CASE 810-03
F N DETAIL Z D 28 PL 0.18 (0.007)
14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. MOLD PROTRUSION SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION R TO BE DETERMINED AT DATUM -T-. DIM A B C D E F G H K L M N P R S INCHES MIN MAX 0.720 0.730 0.395 0.405 0.128 0.148 0.015 0.020 0.088 0.098 0.026 0.032 0.050 BSC --- 0.020 0.035 0.045 0.025 BSC 0_ 5_ 0.030 0.045 0.435 0.445 0.360 0.380 0.030 0.040 MILLIMETERS MIN MAX 18.29 18.54 10.04 10.28 3.26 3.75 0.39 0.50 2.24 2.48 0.67 0.81 1.27 BSC --- 0.50 0.89 1.14 0.64 BSC 0_ 5_ 0.76 1.14 11.05 11.30 9.15 9.65 0.77 1.01
28
15
M
1
TA
S
H BRK 0.18 (0.007) -A- L G M M E 0.10 (0.004) K DETAIL Z -T-
SEATING PLANE S
TB
S
P -B-
C
R 0.25 (0.010)
S
S TB
S
RADIUS
MOTOROLA FAST SRAM
MCM6229BB 7
28 LEAD 300 MIL SOJ CASE 810B-03
F N DETAIL Z D 24 PL 0.18 (0.007) H BRK L G M E 0.10 (0.004) K DETAIL Z -T-
SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. MOLD PROTRUSION SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION R TO BE DETERMINED AT DATUM -T-. DIM A B C D E F G H K L M N P R S INCHES MIN MAX 0.720 0.730 0.295 0.305 0.128 0.148 0.015 0.020 0.088 0.098 0.026 0.032 0.050 BSC --- 0.020 0.035 0.045 0.025 BSC 0_ 10 _ 0.030 0.045 0.330 0.340 0.260 0.270 0.030 0.040 MILLIMETERS MIN MAX 18.29 18.54 7.50 7.74 3.26 3.75 0.39 0.50 2.24 2.48 0.67 0.81 1.27 BSC --- 0.50 0.89 1.14 0.64 BSC 0_ 10 _ 0.76 1.14 8.38 8.64 6.60 6.86 0.77 1.01
28
15
1
14
M
TA
S
S
-A-
0.18 (0.007) P -B-
S
TB
M
C
R 0.25 (0.010)
S
S RADIUS TB
S
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. 81-3-5487-8488
MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 INTERNET: http://motorola.com/sps
MCM6229BB 8
MOTOROLA MCM6229BB/D FAST SRAM

▲Up To Search▲

Price & Availability of MCM6229BBXJ17

	To Download MCM6229BBXJ17 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .