![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
tm TE CH Preliminary T35L3232B SYNCHRONOUS BURST SRAM FEATURES E FT pin for user configurable pipeline or flow-through operation. E Fast Access times: - Pipeline - 3.8 / 4 / 4.5 ns - Flow-through - 9 / 10 / 11ns ESingle 3.3V +0.3V/-0.165V power supply ECommon data inputs and data outputs EIndividual BYTE WRITE ENABLE and GLOBAL WRITE control E Three chip enables for depth expansion and address pipelining E Clock-controlled and registered address, data I/Os and control signals EInternally self-timed WRITE CYCLE EBurst control pins ( interleaved or linear burst sequence) EHigh 30pF output drive capability at rated access time ESNOOZE MODE for reduced power standby E Burst Sequence : - Interleaved (MODE=NC or VCC) - Linear (MODE=GND) 32K x 32 SRAM Pipeline and Flow-Through Burst Mode GENERAL DESCRIPTION The Taiwan Memory Technology Synchronous Burst RAM family employs high-speed, low power CMOS design using advanced triple-layer polysilicon, double-layer metal technology. Each memory cell consists of four transistors and two high valued resistors. The T35L3232B SRAM integrates 32,768 x 32 bits SRAM cells with advanced synchronous peripheral circuitry and a 2-bit counter for internal burst operation. All synchronous inputs are gated by registers controlled by a positive-edge-triggered clock input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining chip enable ( CE ), depthexpansion chip enables (CE2 and CE2), burst control inputs (ADSC , ADSP, and ADV ), write enables ( BW1, BW2 , BW3 , BW4 , and BWE ), and global write (GW ). Asynchronous inputs include the output enable ( OE ), Snooze enable (ZZ) and burst mode control (MODE). The data outputs (Q), enabled by OE , are also asynchronous. Addresses and chip enables are registered with either address status processor ( ADSP) or address status controller (ADSC ) input pins. Subsequent burst addresses can be internally generated as controlled by -3.8 3.8ns 6.6ns 9ns 10.5ns -4 4ns 7.5ns 10ns 15ns -4.5 4.5ns 8.5ns 11ns 15ns the burst advance pin (ADV ). Address and write controls are registered on-chip to initiate self-timed WRITE cycle. WRITE cycles can be one to four bytes wide as controlled by the write control inputs. Individual byte write allows individual byte to be written. OPTIONS MARKING Access Pipeline time 3-1-1-1 Cycle time Access Flowtime through Cycle 2-1-1-1 time Package 100-pin QFP 100-pin TQFP Q T Pkg. Q T BW1 controls DQ1-DQ8. BW2 controls DQ9-DQ16. BW3 controls DQ17-DQ 24. BW4 controls DQ25-DQ32. BW1, BW2 , BW3, and BW4 can be active only with BWE being LOW. GW being LOW causes all bytes to be written. WRITE pass-through capability allows written data available at the output for the immediately next READ cycle. This device also incorporates pipelined enable circuit for easy depth expansion without penalizing system performance. Part Number Examples PART NO. T35L3232B-3.8Q T35L3232B-4T Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 1 Publication Date: FEB. 2000 Revision:0.A tm A0-A14 MODE ADV CLK TE CH Preliminary T35L3232B FUNCTIONAL BLOCK DIAGRAM 15 ADDRESS REGISTER 15 13 15 A0 A1 A1' Q1 BINARY COUNTER & LOGIC Q0 A0' ADSC ADSP CLR BWE BYTE 4 WRITE REGISTER BW4 8 BYTE 4 WRITE DRIVER 8 8 BYTE 3 WRITE REGISTER BW3 8 BYTE 2 WRITE REGISTER BW2 8 BYTE 1 WRITE REGISTER BW1 GW FT CE CE2 CE2 OE ENABLE REGISTER BYTE 1 WRITE DRIVER BYTE 2 WRITE DRIVER BYTE 3 WRITE DRIVER 8 32 32K x 8 x 4 MEMORY ARRAY 8 SENSE AMPS 32 OUTPUT BUFFERS 32 DQ1 E E E DQ32 8 INPUT REGISTERS 4 Note: The Functional Block Diagram illustrates simplified device operation. See Truth Table, pin descriptions and timing diagrams for detailed information. Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 2 Publication Date: FEB. 2000 Revision:0.A tm NC DQ17 DQ18 VCCQ VSSQ DQ19 DQ20 DQ21 DQ22 VSSQ VCCQ DQ23 DQ24 FT VCC NC VSS DQ25 DQ26 VCCQ VSSQ DQ27 DQ28 DQ29 DQ30 VSSQ VCCQ DQ31 DQ32 NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 TE CH Preliminary T35L3232B PIN ASSIGNMENT (Top View) ADSC ADSP BWE BW4 BW3 BW2 BW1 VCC ADV VSS CE2 CE2 CLK GW OE CE A8 A6 A7 A9 100 9 9 9 8 9 7 9 69 5 9 49 39 29 19 0 8 888 7 8 6 8 5 8 4 8 3 8 2 8 1 9 80 79 78 77 76 75 74 73 72 71 70 69 NC DQ16 DQ15 VCCQ VSSQ DQ14 DQ13 DQ12 DQ11 VSSQ VCCQ DQ10 DQ9 VSS NC VCC ZZ DQ8 DQ7 VCCQ VSSQ DQ6 DQ5 DQ4 DQ3 VSSQ VCCQ DQ2 DQ1 NC 100-pin QFP or 100-pin TQFP 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 31 MODE A5 3 23 3 3 43 5 3 63 7 3 83 9 4 04 1 VCC VSS NC NC A4 A3 A2 A1 A0 4 24 3 4 44 5 4 6 4 74 8 4 9 A10 A11 A12 A13 A14 NC NC 50 NC NC Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 3 Publication Date: FEB. 2000 Revision:0.A tm C LK ADSP TE CH t KC Preliminary T35L3232B PIPELINE READ TIMING t KH t KL t ADSS t ADSH t ADSS t ADSH ADS C t AS t AH ADDRESS A1 t WS t WH A2 A3 Burst continued with new base address. GW, BWE, BW 1- BW4 t CES t CEH Deselect cycle. CE (NOTE2) t AAS t AAH ADV ADV suspends burst. OE (NOTE3) t KQLZ tOEHZ t OEQ tOELZ t KQ t KQX t KQHZ t KQX Q High-Z t KQ Q(A1) Q(A2) (NOTE1) Q(A2+1) Q(A2+2) Q(A2+3) Q(A2) Q(A2+1) Q(A3) Burst wraps around to its inital state. BURST READ Sing le READ DON' T CARE UNDEFINED Note: 1. Q(A2) refers to output from address A2. Q (A2 + 1) refers to output from the next internal burst address following A2. 2. CE2 and CE2 have timing identical to CE . On this diagram, when CE is LOW, CE2 is LOW and CE2 is HIGH. When CE is HIGH, CE2 is HIGH and CE2 is LOW. 3. Timing is shown assuming that the device was not enabled before entering into this sequence. OE does not cause Q to be driven until after the following clock rising edge. Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 12 Publication Date: FEB. 2000 Revision:0.A tm CLK ADSP TE CH t KC Preliminary T35L3232B FLOW-THROUGH READ TIMING t K H t KL t AD S S t A D S H t AD S S t A D S H AD S C t AS t A H D e s e le c t C y c le ( NO T E 4 ) AD D R E S S A1 t WS t WH A2 GW, BWE, BW1-BW4 t CE S t CE H CE (NO TE2) t A A S t A AH AD V AD V s us pe n ds bu rs t . OE t O EQ t K Q LZ tO EHZ tO EL Z t KQ t K QX t KQ HZ Q High-Z t KQ Q (A1 ) Q (A2 ) Q (A2 +1 ) (NOTE 1 ) Q (A2 +2 ) Q (A2 +3 Q(A2 ) ) Q (A2 +1 ) +2 ) Q (A2 B ur s t w ra ps a ro und to its inita l s ta te . B U R ST R E AD S i n g le R E A D DON'T CARE UNDEFINED Note: 1. Q(A2) refers to output from address A2. Q (A2 + 1) refers to output from the next internal burst address following A2. 2. CE2 and CE2 have timing identical to CE . On this diagram, when CE is LOW, CE2 is LOW and CE2 is HIGH. When CE is HIGH, CE2 is HIGH and CE2 is LOW. 3. Timing is shown assuming that the device was not enabled before entering into this sequence. OE does not cause Q to be driven until after the following clock rising edge. 4. Output are disabled tKQHZ after diselect. Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 13 Publication Date: FEB. 2000 Revision:0.A tm TE CH t KC Preliminary T35L3232B WRITE TIMING CLK t KH t KL t ADSS t ADSH AD SP t ADSS t ADSH ADSC extends burst. t ADSS t ADSH ADS C t AS t AH AD DRESS A1 A2 BYT E W RIT E s ignals a re ignored for first cycle when ADSP init ialtes bu rst. A3 t WS t WH BWE, BW 1-BW4 t WS t WH (NOTE5) GW t CES t CEH CE (NOTE2) t AAS t AAH ADV (NOTE4) ADV suspnds burst. OE (NOTE3) t DS t DH D High-Z D(A1) tOEHZ D(A2) D(A2+1) (NOTE1) D(A2+1) D(A2+2) D(A2+3) D(A3) D(A3+1) D(A3+2) Q BURST READ Single W RIT E BURST W RITE Exte nde d BURST WRITE DO N' T CARE UNDEFINED Note: 1. Q(A2) refers to output from address A2. Q (A2 + 1) refers to output from the next internal burst address following A2. 2. CE2 and CE2 have timing identical to CE . On this diagram, when CE is LOW , CE2 is LOW and CE2 is HIGH. When CE is HIGH , CE2 is HIGH and CE2 is LOW. 3. OE must be HIGH before the input data setup and hold HIGH throughout the data hold time. This prevents input/output data contention for the time period to the byte write enable inputs being sampled. 4. ADV must be HIGH to permit a WRITE to the loaded address. 5. Full width WRITE can be initiated by GW LOW or GW HIGH and BWE , BW1- BW4 LOW. Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 14 Publication Date: FEB. 2000 Revision:0.A tm TE CH Preliminary T35L3232B PIPELINE READ/WRITE TIMING t KC CLK t KH t KL t ADSS t ADSH ADSP ADS C t AS t AH ADDRESS A1 A2 A3 t WS t WH A4 A5 A6 BWE BW 1- B W4 t CES t CEH CE (NOTE2) ADV OE t KQ t DS t DH tOELZ D(A5) t KQ (NOTE1) Q(A2) Single WRIT E Q(A3) Pass-through READ Q(A4) Q(A4+1) Q(A4+2) Q(A4+3) Back-to-Back WRITEs D(A6) D High-Z t KQLZ tOEHZ D(A3) Q High-Z Q(A1) Back-to-Back READs BURST READ DON' T CARE UNDEFINED Note: 1. Q(A4) refers to output from address A4. Q (A4 + 1) refers to output from the next internal burst address following A4. 2. CE2 and CE2 have timing identical to CE . On this diagram, when CE is LOW, CE2 is LOW and CE2 is HIGH. When CE is HIGH, CE2 is HIGH and CE2 is LOW. 3. The data bus (Q) remains in High-Z following a WRITE cycle unless an ADSP , ADSC or ADV cycle is performed. 4. GW is HIGH. 5. Back-to-back READs may be controlled by either ADSP or ADSC. Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 15 Publication Date: FEB. 2000 Revision:0.A tm CLK AD S P TE CH t KC Preliminary T35L3232B FLOW-THROUGH READ/WRITE TIMING t K H t KL t AD S S t AD S H AD S C t AS t AH AD D R E S 1 AS A2 A3 t WS t WH A4 A5 A6 BW E BW1-BW4 (NOTE4) t CE S t CE H CE (NOTE2) AD V OE t DS t DH tO EL Z D High-Z tO E HZ D (A3 ) t KQ (NO TE 1 ) D (A5 ) D (A6 ) Q Q (A1 ) Q (A2 ) Q (A4 ) Q (A4 +1 ) Q (A4 +2 ) Q (A4 +3 ) B a c k -t o -B a c k R E A D s S i ng le W R IT E BUR ST R EAD B a c k -to -B a c k W R ITE s DO N' T CARE UNDEFINED Note: 1. Q(A4) refers to output from address A4. Q (A4 + 1) refers to output from the next internal burst address following A4. 2. CE2 and CE2 have timing identical to CE . On this diagram, when CE is LOW, CE2 is LOW and CE2 is HIGH. When CE is HIGH, CE2 is HIGH and CE2 is LOW. 3. The data bus (Q) remains in High-Z following a WRITE cycle unless an ADSP , ADSC or ADV cycle is performed. 4. GW is HIGH. 5. Back-to-back READs may be controlled by either ADSP or ADSC. Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 16 Publication Date: FEB. 2000 Revision:0.A tm TE CH Preliminary T35L3232B PACKAGE DIMENSIONS 100-LEAD QFP SSRAM (14 x 20 mm) SYMBOL A A1 A2 b D E e HD' HE' L' L1' t y c DIMENSIONS IN INCHES 0.130(MAX) 0.112O0.005 0.004(MIN) 0.012+0.004-0.002 0.551O0.005 0.787O0.005 0.026O0.006 0.677O0.008 0.913O0.008 0.032O0.008 0.063O0.008 0.006+0.004-0.002 0.004(MAX) 0C~12C DIMENTION IN MM 3.302(MAX) 2.845O0.127 0.102(MIN) 0.300+0.102-0.051 14.000O0.127 20.000O0.127 0.650O0.152 17.200O0.203 23.200O0.203 0.800O0.203 1.600O0.203 0.150+0.102-0.051 0.102(MAX) 0C~12C Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P.17 Publication Date: FEB. 2000 Revision:0.A tm TE CH Preliminary T35L3232B PACKAGE DIMENSIONS 100-LEAD TQFP SSRAM (14 x 20 mm) SYMBOL A A1 A2 b D E e HD' HE' L' L1' t y c DIMENSIONS IN INCHES 0.063(MAX) 0.055O0.005 0.002(MIN) 0.013+0.002-0.004 0.551O0.004 0.787O0.004 0.026O0.006 0.630O0.004 0.866O0.004 0.024O0.006 0.039O0.006 0.006O0.002 0.003(MAX) 0C~7C DIMENTION IN MM 1.600(MAX) 1.400O0.050 0.050(MIN) 0.320+0.060-0.100 14.000O0.100 20.000O0.100 0.650O0.152 16.000O0.100 22.000O0.100 0.600O0.150 1.000O0.150 0.150+0.050-0.060 0.080(MAX) 0C~7C Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P.18 Publication Date: FEB. 2000 Revision:0.A tm PINS TE CH Preliminary T35L3232B PIN DESCRIPTIONS DESCRIPTION Addresses: These inputs are registered and must meet the setup and 32-37, 44-48, Inputhold times around the rising edge of CLK. The burst counter 81, 82, 99, A0-A14 Synchronous generates internal addresses associated with A0 and A1, during 100, burst cycle and wait cycle. SYM. TYPE 93-96 BW1 BW2 BW3 BW4 Byte Writes: A byte write is LOW for a WRITE cyle and HIGH for a READ cycle. BW1 controls DQ1-DQ8. BW2 controls DQ9InputDQ16. BW3 controls DQ17-DQ24. BW4 controls DQ25-DQ32. Synchronous Data I/O are high impedance if either of these inputs are LOW , conditioned by BWE being LOW. Write Enable: This active LOW input gates byte write operations Inputand must meet the setup and hold times around the rising edge of Synchronous CLK. Global Write: This active LOW input allows a full 32-bit WRITE to Inputoccur independent of the BWE and BWn lines and must meet Synchronous the setup and hold times around the rising edge of CLK. Clock: This signal registers the addresses, data, chip enables, Inputwritecontrol and burst control inputs on its rising edge. All Synchronous synchronous inputs must meet setup and hold times around the clock's rising edge. Synchronous Chip Enable: This active LOW input is used to enable Inputthe device and conditions internal use of ADSP. This input is Synchronous sampled only when a new external address is loaded. Synchronous Chip Enable: This active LOW input is used to enable Inputthe device. This input is sampled only when a new external address Synchronous is loaded. This input can be used for memory depth expansion. Synchronous Chip Enable: This active HIGH input is used to enable Inputthe device. This input is sampled only when a new external address Synchronous is loaded. This input can be used for memory depth expansion. Input Output enable: This active LOW asynchronous input enables the data output drivers. 87 BWE 88 GW 89 CLK 98 CE 92 CE2 97 CE2 86 OE 83 ADV Address Advance: This active LOW input is used to control the Inputinternal burst counter. A HIGH on this pin generates wait cycle Synchronous (no address advance). Address Status Processor: This active LOW input, along withCE Inputbeing LOW, causes a new external address to be registered and a Synchronous READ cycle is initiated using the new address. 84 ADSP Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 4 Publication Date: FEB. 2000 Revision:0.A tm 85 TE CH Preliminary T35L3232B SYM. TYPE DESCRIPTION PIN DESCRIPTIONS (continued) QFP PINS Address Status Controller:This active LOW input causes Inputdevice to be deselected or selected along with new external Synchronous address to be registered. A READ or WRITE cycle is initiated depending upon write control inputs. InputStatic InputStatic A LOW on this pin selects in flow-through mode. A NC or HIGH on this pin selects in pipeline mode. Mode: This input selects the burst sequence. A LOW on this pin selects LINEAR BURST. A NC or HIGH on this pin selects INTERLEAVED BURST. Do not alter input state while device is operating. Snooze Enable: This active HIGH asynchronous input causes the device to enter a low-power standby mode in which all data in the memory arry is retained. ADSC 14 FT 31 MODE 64 ZZ Input 2, 3, 6-9, 12, 13, 18, 19, 22-25, 28, 29, 52, 53, 56-59, 62, 63, 68, 69, 72-75, 78, 79, 15,41,65,91 17,40,67,90 4,11,20,27,54, 61,70,77 5,10,21,26,55, 60,71,76 1,16,30,38, 39,42,43,49, 50, 51, 66,80 DQ1DQ32 Input/ Output Data Inputs/Outputs: First Byte is DQ1-DQ8. Second Byte is DQ9-DQ16. Third Byte is DQ17-DQ24. Fourth Byte is DQ25DQ32. Input data must meet setup and hold times around the rising edge of CLK. Power Supply: 3.3V +10%/-5% Ground: GND Output Buffer Supply: 3.3V +10%/-5% Output Buffer Ground: GND VCC VSS VCCQ VSSQ Supply Ground I/O Supply I/O Ground NC - No Connect: These signals are not internally conntected. Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 5 Publication Date: FEB. 2000 Revision:0.A tm TE CH Preliminary T35L3232B INTERLEAVED BURST ADDRESS TABLE (MODE = NC/VCC) First Address (external) A...A00 A...A01 A...A10 A...A11 Second Address (internal) A...A01 A...A00 A...A11 A...A10 Third Address (internal) A...A10 A...A11 A...A00 A...A01 Fourth Address (internal) A...A11 A...A10 A...A01 A...A00 LINEAR BURST ADDRESS TABLE (MODE = GND) First Address (external) A...A00 A...A01 A...A10 A...A11 Second Address (internal) A...A01 A...A10 A...A11 A...A00 Third Address (internal) A...A10 A...A11 A...A00 A...A01 Fourth Address (internal) A...A11 A...A00 A...A01 A...A10 PARTIAL TRUTH TABLE FOR READ/WRITE Function READ READ WRITE one byte WRITE all byte WRITE all byte GW H H H H L BWE H L L L X BW1 X H L L X BW2 X H H L X BW3 X H H L X BW4 X H H L X Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P. 6 Publication Date: FEB. 2000 Revision:0.A tm TE CH Preliminary T35L3232B TRUTH TABLE OPERATION Deselected Cycle, Power Down Deselected Cycle, Power Down Deselected Cycle, Power Down Deselected Cycle, Power Down Deselected Cycle, Power Down Snooze Cycle, Power Down READ Cycle, Begin Burst READ Cycle, Begin Burst WRITE Cycle, Begin Burst READ Cycle, Begin Burst READ Cycle, Begin Burst READ Cycle, Continue Burst READ Cycle, Continue Burst READ Cycle, Continue Burst READ Cycle, Continue Burst WRITE Cycle, Continue Burst WRITE Cycle, Continue Burst READ Cycle, Suspend Burst READ Cycle, Suspend Burst READ Cycle, Suspend Burst READ Cycle, Suspend Burst WRITE Cycle, Suspend Burst WRITE Cycle, Suspend Burst ADDRESS USED CE CE2 CE2 ZZ ADSP ADSC ADV WRITE OE CLK DQ None None None None None None External External External External External Next Next Next Next Next Next Current Current Current Current Current Current H L L L L X L L L L L X X H H X H X X H H X H X X H X H X L L L L L X X X X X X X X X X X X X L X L X X H H H H H X X X X X X X X X X X X L L L L L H L L L L L L L L L L L L L L L L L X L L H H X L L H H H H H X X H X H H X X H X L X X L L X X X L L L H H H H H H H H H H H H X X X X X X X X X X X L L L L L L H H H H H H X X X X X X X X L H H H H H H L L H H H H L L X X X X X X L H X L H L H L H X X L H L H X X L-H L-H L-H L-H L-H X L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H L-H High-Z High-Z High-Z High-Z High-Z High-Z Q High-Z D Q High-Z Q High-Z Q High-Z D D Q High-Z Q High-Z D D Note: 1. X means "don't care." H means logic HIGH. L means logic LOW. WRITE = L means any one or more byte write enable signals (BW1, BW2 , BW3 or BW4 ) and BWE are LOW, or GW equals LOW. WRITE = H means all byte write signal are HIGH. 2. BW1= enables write to DQ1-DQ8. BW2 = enables write to DQ9-DQ16. BW3 = enables write to DQ17-DQ24. BW4 =enables write to DQ25-DQ32. 3. All inputs except OE and ZZ must meet setup and hold times around the rising edge ( LOW to HIGH) of CLK. 4. Suspending burst generates wait cycle. 5. For a write operation following a read operation. OE must be HIGH before the input data required setup time plus High-Z time for OE and staying HIGH throughout the input data hold time. 6. This device contains circuitry that will ensure the outputs will be High-Z during power-up. 7. ADSP= LOW along with chip being selected always initiates an internal READ cycle at the L-H edge of CLK. A WRITE cycle can be performed by setting WRITE LOW for the CLK L-H edge of the subsequent wait cycle. Refer to WRITE timing diagram for clarification. Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P.7 Publication Date: FEB. 2000 Revision:0.A tm TE CH Preliminary T35L3232B *Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. ABSOLUTE MAXIMUM RATINGS* Voltage on VCC Supply Relative to VSS. ............-0.5V to +4.6V I/O Supply Voltage VccQ ........... Vss -0.5V to Vcc VIN......................................... -0.5V to Vcc +0.5V Storage Temperature (plastic)...... -55C to +150C Junction Temperature ............................... +150C Power Dissipation ........................................ 1.0W Short Circuit Output Current...................... 100mA DC ELECTRICAL CHARACTERISTICS AND RECOMMENDED OPERATING CONDITIONS (0C Ta 70C; VCC = 3.3V +10%/-5% unless otherwise noted) DESCRIPTION Input High (Logic) voltage Input Low (Logic) voltage Input Leakage Current Output Leakage Current Output High Voltage Output Low Voltage Supply Voltage CONDITIONS SYM. VIH VIL 0V VIN VCC Output(s) disabled, 0V VOUT VCC IOH = -4.0 mA IOL = 8.0 mA ILI ILO VOH VOL Vcc MIN 2 -0.3 -2 -2 2.4 3.1 0.4 3.6 MAX. CONDITIONS Device selected; all inputs VIL or Power Supply VIH; cycle time tKC MIN; VCC Current : Operating = MAX; outputs open Device selected;ADSC ,ADSP, Power Supply Current: Idle DESCRIPTION SYM. TYP ICC TBD -3.8 250 -4 200 -4.5 150 UNITS NOTES mA 3, 12, 13 MAX VCCQ + 0.3 0.8 2 2 UNITS V V A A V V V NOTES 1, 2 1, 2 14 1, 11 1, 11 1 ADV , GW , BWE VIH; all other inputsVIL orVIH; VCC = MAX; cycle time tKC MIN: outputs open Device deselected; VCC = MAX; all inputs VSS + 0.2 or VCC - 0.2; all inputs static; CLK frequency =0 Device deselected; all inputs VIL or VIH; all inputs static; VCC = MAX;CLK frequency = 0 Device deselected; all inputs VIL or VIH; VCC =MAX; CLK cycle ISB1 TBD 60 60 60 mA 12, 13 CMOS Standby ISB2 TBD 10 10 10 mA 12, 13 TTL Standby ISB3 TBD 25 25 25 mA 12, 13 Clock Running ISB4 TBD 60 60 60 mA 12, 13 time tKCMIN Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P.8 Publication Date: FEB. 2000 Revision:0.A tm TE CH Preliminary T35L3232B AC ELECTRICAL CHARACTERISTICS (Note 5) (0CTA70C;VCC=3.3V +0.3V/-0.165V) DESCRIPTION SYM. -3.8 -4 -4.5 UNITS NOTES MIN MAX MIN MAX MIN MAX Clock(pipeline) Clock cycle time Clock to output valid Clock to output invalid Clock to output in Low-Z Clock(flow-through) Clock cycle time Clock to output valid Clock to output invalid Clock to output in Low-Z Output Times Clock HIGH time Clock LOW time Clock to output in High-Z OE to output valid OE to output in Low-Z OE to output in High-Z Setup Times Address Address Status( ADSC , ADSP ) Address Advance ( ADV ) Byte Write Enables ( BW1~ BW4 , BWE , GW ) Data-in Chip Enables( CE , CE2 ,CE2) Hold Times Address Address Status( ADSC , ADSP ) Address Advance ( ADV ) Byte Write Enables ( BW1~ BW4 , BWE , GW ) Data-in Chip Enables( CE , CE2 ,CE2) tKC tKQ tKQX tKQLZ tKC tKQ tKQX tKQLZ tKH tKL tKQHZ tOEQ tOELZ tOEHZ tAS 6.6 3.8 1.5 1.5 10.5 9.0 3 3 1.8 1.8 5 5 0 5 1.7 7.5 4 2 2 15 10 3 3 1.9 1.9 5 5 0 5 2.0 2.0 2.0 2.0 2.0 2.0 0.5 0.5 0.5 0.5 0.5 0.5 8.5 4.5 2 2 15 11 3 3 2.0 2.0 5 5 0 5 2.0 2.0 2.0 2.0 2.0 2.0 0.5 0.5 0.5 0.5 0.5 0.5 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 6, 7 6, 7 9 6, 7 6, 7 8, 10 8, 10 8, 10 8, 10 8, 10 8, 10 8, 10 8, 10 8, 10 8, 10 8, 10 8, 10 tADSS 1.7 tAAS 1.7 tWS tDS tCES tAH tADSH tAAH tWH tDH tCEH 1.7 1.7 1.7 0.5 0.5 0.5 0.5 0.5 0.5 Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P.9 Publication Date: FEB. 2000 Revision:0.A tm TE CH Preliminary T35L3232B CONDITIONS TA = 25C; f = 1 MHz VCC = 3.3V SYM. CI CO TYP 3 6 MAX 4 7 UNITS NOTES pF pF 4 4 CAPACITANCE DESCRIPTION Input Capacitance Input/ Output Capacitance(DQ) THERMAL CONSIDERATION DESCRIPTION Thermal Resistance - Junction to Ambient Thermal Resistance - Junction to Case CONDITIONS Still air, soldered on 4.25x1.125 inch 4-layer PCB SYM. QFP TYP UNITS JA 20 C/W JB 1 C/W NOTES AC TEST CONDITIONS Input pulse levels Input rise and fall times Input timing reference levels Output reference levels Output load 0V to 3.0V 1.5ns 1.5V 1.5V See Figures 1 and 2 7. At any given temperature and voltage condition, tKQHZ is less than tKQLZ and tOEHZ is less than tOELZ. 8. A READ cycle is defined by byte write enables all HIGH or ADSP LOW along with chip enables being active for the required setup and hold times. A WRITE cycle is defined by at one byte or all byte WRITE per READ/WRITE TRUTH TABLE. 9. OE is a "don't care" when a byte write enable is sampled LOW. 10.This is a synchronous device. All synchronous inputs must meet specified setup and hold time, except for "don't care" as defined in the truth table. 11.AC I/O curves are available upon request. 12."Device Deselected means the device is in POWER-DOWN mode as defined in the truth table. "Device Selected" means the device is active. 13.Typical values are measured at 3.3V, 25C and 20ns cycle time. 14.MODE pin has an internal pull-up and exhibits an input leakage current of 10A. Notes: 1. All voltages referenced to VSS (GND). 2. Overshoot: VIH +3.6 V for t tKC/2. Undershoot: VIL -1.0 V for t tKC/2. 3. Icc is given with no output current. Icc increases with greater output loading and faster cycle times. 4. This parameter is sampled. 5. Test conditions as specified with the output loading as shown in Fig. 1 unless otherwise noted. 6. Output loading is specified with CL = 5 pF as in Fig. 2. OUTPUT LOADS Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P.10 Publication Date: FEB. 2000 Revision:0.A tm DQ TE CH Preliminary T35L3232B 3.3V 317 ohm DQ 50 ohm 351 ohm 5 pF Z0 = 50 ohm Vt = 1.5V Fig. 2 output load equivalent Fig. 1 output load equivalent Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P.11 Publication Date: FEB. 2000 Revision:0.A tm TE CH Preliminary T35L3232B device to enter SNOOZE MODE. When the ZZ pin becomes a logic HIGH, IZZ is guaranteed after the setup time tZZ is met. Any access pending when entering SNOOZE MODE is not guaranteed to successfully complete. Therefore, SNOOZE MODE must not be initiated until valid pending operations are completed. SNOOZE MODE SNOOZE MODE is a low current, "power down" mode in which the device is deselected and current is reduced to IZZ. The duration of SNOOZE MODE is dictated by the length of time the ZZ pin is in a HIGH state. After entering SNOOZE MODE, the clock and all other inputs are ignored. The ZZ pin (pin 64) is an asynchronous, active HIGH input that causes the SNOOZE MODE ELECTRICAL CHARACTERISTICS DESCRIPTION Current during SNOOZE MODE ZZ HIGH to SNOOZE MODE time SNOOZE MODE Operation Recovery Time CONDITIONS ZZ VIH SYMBOL IZZ tZZ tRZZ 2(tKC) 2(tKC) MIN MAX 5 UNITS mA ns ns 4 4 NOTES SNOOZE MODE WAVEFORM CLK CE t RZZ ZZ tZZ I S U PP LY I SUPPLY I ZZ DON' T CARE Note: 1. The CE signal shown above refers to a TRUE state on all chip selects for the device. 2. All other inputs held to static CMOS levels (VIN Vss + 0.2 V or Vcc -0.2 V). Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. P.12 Publication Date: FEB. 2000 Revision:0.A |
Price & Availability of T35L3232B
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |