|
|
 |
http:// Atmel, Corp. Atmel Corp.
|
Part No. |
AT49LH004 AT49LH004-33JC AT49LH004-33TC
|
OCR Text |
...x interface, then the pin will exhibit some leakage current. x x input clk fwh/lpc clock : this pin is used to provide a clock to the device. this pin is usually connected to the 33 mhz pci clock and adheres to the pci specification. thi... |
Description |
4-megabit Firmware Hub and Low-Pin Count Flash Memory 512K X 8 FLASH 3V PROM, 11 ns, PDSO40 4-megabit Firmware Hub and Low-Pin Count Flash Memory 512K X 8 FLASH 3V PROM, 11 ns, PQCC32
|
File Size |
276.40K /
36 Page |
View
it Online |
Download Datasheet
|
|
|
 |
Atmel
|
Part No. |
AT49LW080
|
OCR Text |
...h (a/a mux mode), this pin will exhibit a leakage current of approximately 200 a. this pin may be floated, which will select fwh mode. rst input x x interface reset: valid for both a/a mux and fwh interface operations. when driven low, ... |
Description |
8M Firmware Hub
|
File Size |
222.46K /
32 Page |
View
it Online |
Download Datasheet
|
|
|
 |
Analog Devices, Inc.
|
Part No. |
AD743SQ/883B AD743JN
|
OCR Text |
...furthermore, the ad743 does not exhibit an output phase reversal when the negative common-mode voltage limit is exceeded. the ad743s guaranteed, maximum input voltage noise of 4.0 nv/ ? hz at 10 khz is unsurpassed for a fet-input monolithi... |
Description |
Ultralow Noise BiFET Op Amp OSCILLATORS 50PPM -10 70 1.8V 4 50.000MHZ TS LVHCMOS 5.0X3.2MM 4PAD SMD
|
File Size |
310.95K /
12 Page |
View
it Online |
Download Datasheet
|
|
|
 |
Microsemi
|
Part No. |
SLVU2.8K-4
|
OCR Text |
...minimum voltage the device will exhibit at a specified cu rrent v sb snap - back voltage: the minimum snap - back voltage the device will exhibit at a specified current v c clamping voltage: maximum clamping voltage across the t... |
Description |
Transient Voltage Suppressor
|
File Size |
83.36K /
3 Page |
View
it Online |
Download Datasheet
|
|
|
 |
Microsemi
|
Part No. |
SLVG2.8K
|
OCR Text |
...minimum voltage the device will exhibit at a specified current v sb snap - back voltage: the minumum snap - back voltage the device wi ll exhibit at a specific current v c clamping voltage: maximum clamping voltage across the tv... |
Description |
Transient Voltage Suppressor
|
File Size |
159.29K /
2 Page |
View
it Online |
Download Datasheet
|
|
|
 |
Microsemi
|
Part No. |
SLVE2.8K
|
OCR Text |
...minimum voltage the device will exhibit at a specified current. v sb snap-back voltage: the minimum snap back voltage the device will exhibit at a specific current. v c clamping voltage: maximum clamping voltage across the tvs de... |
Description |
Transient Voltage Suppressor
|
File Size |
188.72K /
2 Page |
View
it Online |
Download Datasheet
|
|
|
 |
Xicor
|
Part No. |
AN141
|
OCR Text |
...ully discharged. (see appendix exhibit 2). thus it takes less time to correct for a voltage mismatch, assuming a constant charge/ discharge current, when the cells are nearly fully charged. for example, a nearly full or nearly empty cell... |
Description |
The Benefits of Cell Balancing
|
File Size |
170.94K /
13 Page |
View
it Online |
Download Datasheet
|
|
|
 |
Electronic Theatre Controls, Inc.
|
Part No. |
AN103
|
OCR Text |
...iconix 2n4340, j202, and sst202 exhibit typical g oss = 2 s at v ds = 20 v. these devices in the circuit of figure 4 will provide a current source adjustable from 5 a to 0.8 ma with internal impedance greater than 2 m at 0.2 ma. ... |
Description |
The FET Constant-Current Source/Limiter
|
File Size |
45.12K /
5 Page |
View
it Online |
Download Datasheet
|
|

Price and Availability
|